Which power amplifier has maximum efficiency?

Which power amplifier has maximum efficiency? A. Class B B. Class C C. Class A D. all are equally efficient
by

1 Answer

Answer :

Class B power amplifier has maximum efficiency.

by

Related questions

In a CB amplifier the maximum efficiency could be

Last Answer : In a CB amplifier the maximum efficiency could be 25%.

Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Description : Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Last Answer : Parameter Class A Class B 

Define the term related to power amplifier. (i) Efficiency (ii) Voltage gain

Description : Define the term related to power amplifier. (i) Efficiency (ii) Voltage gain

Last Answer : (i) Efficiency: Efficiency of the power amplifier is defined as the ratio of maximum a.c. output power to the d.c. input power. Mathematically (ii) Voltage gain: Voltage gain of the power amplifier is defined as the ratio of output voltage to the input voltage. Mathematically,

A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, what is the antenna current at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Description : A final amplifier of a radio transmitter draws 250 mA of plate current when the plate supply voltage is 1400 volts. If the plate circuit efficiency is 80% and the transmitter is connected to an antenna having a feed impedance of 70 ohms, ... at the feed-point? A. 4.0 A B. 2.2 A C. 1.25 A D. 2.0 A

Last Answer : D. 2.0 A

What is the efficiency of Class-B amplifier?

Description : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Last Answer : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

The efficiency of a class B push-pull amplifier is

Description : The efficiency of a class B push-pull amplifier is

Last Answer : The efficiency of a class B push-pull amplifier is 75-80%

When a source is delivering maximum power to a load, the efficiency of the circuit is always

Description : When a source is delivering maximum power to a load, the efficiency of the circuit is always (a) 50% (b) 75% (c) 100% (d) Depends on the circuit parameters

Last Answer : When a source is delivering maximum power to a load, the efficiency of the circuit is always 50%

In class - A power amplifier, the collector dissipation is maximum when

Description : In class - A power amplifier, the collector dissipation is maximum when  (a) no signal is present  (b) signal swing is maximum  (c) signal swing is (1/1.414) of its maximum  (d) none of the above

Last Answer : In class - A power amplifier, the collector dissipation is maximum when no signal is present

The type of power amplifier that exhibits crossover distortion in its output is :

Description : The type of power amplifier that exhibits crossover distortion in its output is : (A) Class A (B) Class B (C) Class AB (D) Class C

Last Answer : The type of power amplifier that exhibits crossover distortion in its output is  Class B

A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -

Description :  A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -  a) 16/9 b) 4 / 3 c) 3/4 d) 9 /16

Last Answer :  A transformer has maximum efficiency at 3/4 full load. The ratio of its iron losses and full load copper loss is : -  9 /16

when will be the maximum efficiency of transformer?

Last Answer : Transformer efficiency is maximum when copper losses are equal to iron losses.

In a variable speed SI engine, the maximum torque occurs at the maximum (a) Speed (b) Brake power (c) Indicated power (d) Volumetric efficiency

Description : In a variable speed SI engine, the maximum torque occurs at the maximum (a) Speed (b) Brake power (c) Indicated power (d) Volumetric efficiency

Last Answer : Ans :d

At what power maximum efficiency of power transformer and distribution transformer is designed

Description : At what power maximum efficiency of power transformer and distribution transformer is designed

Last Answer : Maximum efficiency of the transformer is attained at certain load factor (α) when core losses of transformer is equal to the copper losses. PCore loss = α ^2 X PCopper loss From the ... the day. Hence distribution transformers are designed to have maximum efficiency at 50% of the rated full load

Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Description : Efficiency of power transmission (η) through a circular pipe is given by (ht - hf )/ht , which has a maximum value of __________ percent. (A) 33:3 (B) 50 (C) 66.6 (D) 88.8

Last Answer : (C) 66.6

The energy conversion efficiency of a solar cell does not depend on a) solar energy insolation b) inverter c) area of the solar cell d) maximum power output

Description : The energy conversion efficiency of a solar cell does not depend on a) solar energy insolation b) inverter c) area of the solar cell d) maximum power output

Last Answer : b) inverter

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

74)Power transformers are generally designed to have maximum efficiency around A. No load B. Half load C. Near full load D. 10% overload

Description : 74)Power transformers are generally designed to have maximum efficiency around A. No load B. Half load C. Near full load D. 10% overload

Last Answer : C. Near full load

Power transformers should be designed to have maximum efficiency (a) at one-fourth load (b) at one-half load (c) at or near full load (d) any of the above

Description : Power transformers should be designed to have maximum efficiency (a) at one-fourth load (b) at one-half load (c) at or near full load (d) any of the above

Last Answer : (c) at or near full load

A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at

Description : A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is  (A) 86.7% (B) 88.26% (C) 88.9% (D) 87.8%

Last Answer : A simple phase transformer has a maximum efficiency of 90% at full load and unity power factor. Efficiency at half load at the same power factor is 87.8%

In case the conditions for maximum power for a D.C. motor are established, the efficiency of the motor will be?

Last Answer : In case the conditions for maximum power for a D.C. motor are established, the efficiency of the motor will be less than 50%.

Power transformers are generally designed to have maximum efficiency around?

Last Answer : Power transformers are generally designed to have maximum efficiency around near full-load.

If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Description : If the rf amplifier discussed has an 80 milliwatt input, what would be the maximum output?

Last Answer : 800 watts.

"Efficiency of thermal power station is low". — Justify.

Description : "Efficiency of thermal power station is low". — Justify. 

Last Answer : Justification: Efficiency of thermal power station is low":- Overall efficiency of T.P.P depends upon efficiency of boiler, turbine and alternator. The heat produced due to combustion of coal ... losses in thermal power plant is 71%, So efficiency of thermal power plant is less about 29% 

What will be the efficiency when the transformer operates at unity power factor and 60% of full load

Description : What will be the efficiency when the transformer operates at unity power factor and 60% of full load 

Last Answer : What will be the efficiency when the transformer operates at unity power factor and 60% of full load 96.5%

A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is:

Description : A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: A. 8.57% B. 42.85% C. 4.28% D. 85.7%

Last Answer : A power supply produces a 0.6 W output with an input of 0.7 W. Its percentage of efficiency is: 85.7%

What is the efficiency of transformer compared with that of electrical motors of the same power?

Last Answer : Much higher efficiency of transformer compared with that of electrical motors of the same power.

working of class B push pull amplifier.

Description : working of class B push pull amplifier.

Last Answer : Circuit Diagram:- Operation:  In class B amplifier transistor conduct only for half cycle of input signal.One conduct in positive half cycle and other conducts in negative half ... Then output transformer joins these two halves and produces a full sine wave in the load resistor. 

Compare amplifier and oscillator.

Description : Compare amplifier and oscillator.

Last Answer : Figure shows a block diagram of an amplifier and an oscillator.   An amplifier is a device, which produces an output signal with similar waveform as that of the input. ... is supplied. An oscillator does not require any external signal to start or maintain energy conversion process.

role of tuned LC circuit in tuned amplifier.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

applications of RC coupled amplifier

Description :  applications of RC coupled amplifier

Last Answer : Applications of RC coupled amplifier: (i) Widely used as Voltage amplifiers. (ii) They are used in Public Address System. (iii) In Tape recorders. (iv) In stereo amplifiers (v) In T.V. V.C.R. and C.D. Players.

characteristics of Hi-Fi amplifier system.

Description : characteristics of Hi-Fi amplifier system.

Last Answer : Characteristics of HI-FI amplifier: 1. Signal to noise ratio should be better than 50dB. 2. Frequency response should be flat within +-1dB. 3. Nonlinear distortion should not be more ... provided. 6. Environmental conditions should be such as to eliminate the external noise in listening room. 

two stage amplifier and need of multistage amplifier.

Description :  two stage amplifier and need of multistage amplifier.

Last Answer : Circuit diagram of two stage amplifier : Need of multistage amplifier: The output from a single stage amplifier is usually insufficient to drive an output device. So that ... to second amplifier.  To increase the overall gain of the amplifier multistage amplifier is needed.

advantages and disadvantages of direct coupled amplifier over RC coupled amplifier.

Description : advantages and disadvantages of direct coupled amplifier over RC coupled amplifier. 

Last Answer : Advantages:  Due to absence of coupling capacitors, the gain does not reduce on the lower frequency side.  This amplifier can amplify dc signals. Reduced cost and complexity due to absence of ...   The output waveform has a dc shift.  Poor frequency response at a higher frequency.

transformer coupled amplifier

Description :  transformer coupled amplifier

Last Answer :  transformer coupled amplifier

Single stage CE amplifier

Description : Single stage CE amplifier

Last Answer : Requirement(Necessity) of Multistage amplifier: -In many applications we required a high gain. But sometimes gain produced by an amplifier is not sufficient so to increase the gain, we ... necessity of multistage amplifier is for providing high gain. It is also required for high bandwidth.

What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Description : What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Last Answer : Significance: Signal conditioning means manipulating an analog signal in such a way that it meets the requirements of the next stage for further processing. Signal inputs accepted by signal ... -frequency converters, current-to-voltage converters, current loop converters, and charge converters.  

Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Description : Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Last Answer : Application: 1. In Data acquisition from low output transducers such as strain gauges, Thermocouples, Wheatstone bridge measurements e.t.c 2. In Medical instrumentation, Navigation, Radar ... video data acquisition and imaging 5. High frequency signal amplification in cable RF systems 

State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

Define gain and bandwidth of an amplifier.

Description : Define gain and bandwidth of an amplifier.

Last Answer : Bandwidth  The range of frequency over which the voltage gain is equal to or greater than 70.7% of its maximum value Gain: The ratio of output parameter (voltage/ current /power) to the input parameter (voltage/ current /power) of an amplifier is known as gain. It is denoted by a letter A

Draw diagram of class A push-pull amplifier and explain its operation.

Description : Draw diagram of class A push-pull amplifier and explain its operation. 

Last Answer : Class A Push-pull Amplifier: The circuit diagram of class A push-pull amplifier is as shown in the fig.(a). Operation: The resistors R1 and R2 along with Vcc provide the dc biasing so as ... Vcc is applied to the collectors of transistors Q1 and Q2 through the centretapped output transformer. 

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Description : Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Last Answer : Parameter RC coupled Transformer coupled Direct coupled  Coupling element Resistor and capacitor Transformer No element Impedance matching Poor Excellent good Frequency ... Low frequency amplifier,opamp Size and cost small Large and bulky least

Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Description : Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Last Answer : Operation:- The capacitors C1 and C2 are called as the coupling capacitors. As the load resistor RL (not shown in the diagram) is coupled to the amplifier through the coupling capacitor ... connected in the common emitter (CE) configuration. Therefore, this amplifier is called CE amplifier. 

List the advantages of RC coupled amplifier.

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

State the need of cascade amplifier.

Description : State the need of cascade amplifier.

Last Answer : Most systems a single transistor amplifier does not provide sufficient gain or bandwidth or will not have the correct input or output impedance matching. Hence cascade amplifier is use which consist more than one stages of amplification.

A certain common-emitter amplifier has a voltage gain of 100. If the emitter bypass capacitor is removed.

Description : A certain common-emitter amplifier has a voltage gain of 100. If the emitter bypass capacitor is removed.  a. The circuit will become unstable b. The voltage gain will decrease  c. The voltage gain will increase d. The circuit will become stable

Last Answer : B

If three amplifiers having the same bandwidth are cascaded, the bandwidth of the resulting amplifier will be

Description : If three amplifiers having the same bandwidth are cascaded, the bandwidth of the resulting amplifier will be (a) Better than that of each stage (b) Worse than that of each stage (c) Same as that of each stage (d) None of the above 

Last Answer : If three amplifiers having the same bandwidth are cascaded, the bandwidth of the resulting amplifier will be Worse than that of each stage

In a differential amplifier the differential voltage gain is 500 and the common mode voltage gain is 0.5. ...

Description : In a differential amplifier the differential voltage gain is 500 and the common mode voltage gain is 0.5. The CMRR in dB is (a) 80 (b) 60 (c) 30 (d) 20

Last Answer : Ad - differential voltage gain. Acm- common mode voltage gain CMRR - common mode rejection ratio  CMRR = 20log(Ad/Acm) = 60 dB

The purpose of a coupling capacitor in an amplifier is to:

Description : The purpose of a coupling capacitor in an amplifier is to:  (1) Control the output (2) Provide impedance matching (3) Provide DC isolation between amplifier and load (4) W Increase the bandwidth

Last Answer : The purpose of a coupling capacitor in an amplifier is to: Provide DC isolation between amplifier and load.

One advantage of transformer coupling in transistor amplifier is that:

Description : One advantage of transformer coupling in transistor amplifier is that:  (1) it provides excellent frequency response (2) It is simple and less expensive than others (3) Low power supply may be used (4) High efficiency and high power output is obtained.

Last Answer : One advantage of transformer coupling in transistor amplifier is that: High efficiency and high power output is obtained.