__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength. (A) Lancing (B) Shot peening (C) Slugging (D) Spinning

__________ is the process used for setting up compressive stresses in the surface of a metal to improve its fatigue strength.
(A) Lancing
(B) Shot peening
(C) Slugging
(D) Spinning
by

1 Answer

Answer :

(B) Shot peening
by

Related questions

________ cannot increase the fatigue strength of a material. (A) Grain refining (B) Grain coarsening (C) Surface hardening (D) Shot peening

Description : ________ cannot increase the fatigue strength of a material. (A) Grain refining (B) Grain coarsening (C) Surface hardening (D) Shot peening

Last Answer : (B) Grain coarsening

-The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Description : -The method used to induce a layer of residual compressive stress on the surface of the spring wire, is (A) shot peening (B) burnishing (C) lapping (D) none of the above

Last Answer : (A) shot peening

Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Description : Normalising does not __________ of a metal. (A) Improve machinability & tensile strength (B) Remove internal stresses (C) Refine the structure (D) Remove strains caused by cold working

Last Answer : Option B

Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Last Answer : b) Due to tensile

Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Last Answer : (b) Due to tensile

Cold worked steel parts are normally subjected to (A) Normalising (B) Hardening (C) Annealing (D) Shot peening

Description : Cold worked steel parts are normally subjected to (A) Normalising (B) Hardening (C) Annealing (D) Shot peening

Last Answer : (C) Annealing

Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Description : Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Last Answer : (B) Fatigue

Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength(C) Elastic limit (D) Limit of proportionality

Description : Stresses encountered in the metal forming processes are less than the __________ of the material. (A) Fracture strength (B) Yield strength (C) Elastic limit (D) Limit of proportionality

Last Answer : Option A

A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the metal (B) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal

Description : A member which is subjected to reversible tensile or compressive stress may fail at a stress lower  than the ultimate stress of the material. This property of metal, is called  (A) Plasticity of the ... ) Elasticity of the metal  (C) Fatigue of the metal  (D) Workability of the metal

Last Answer : (C) Fatigue of the metal

Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Description : Fatigue failure of a material results from __________ stress. (A) Tensile (B) Compressive (C) Fluctuating (D) None of these

Last Answer : (C) Fluctuating

Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating(B) Tensile(C) Compressive(D) Torsion

Description : Fatigue failure of a material may occur, when it is subjected to __________ stress. (A) Fluctuating (B) Tensile (C) Compressive (D) Torsion

Last Answer : (A) Fluctuating

The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Description : The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Last Answer : (a) Bond stress

Pick up the correct statement regarding low heat cement from the following: (A) It possesses less compressive strength (B) Its initial setting time is about one hour (C) Its final setting time is about 10 hours (D) All the above

Description : Pick up the correct statement regarding low heat cement from the following: (A) It possesses less compressive strength (B) Its initial setting time is about one hour (C) Its final setting time is about 10 hours (D) All the above

Last Answer : Answer: Option D

Ultra purification of a metal is done by (1) slugging (2) zone melting (3) smelting (4) leaching

Description : Ultra purification of a metal is done by (1) slugging (2) zone melting (3) smelting (4) leaching

Last Answer : (2) zone melting Explanation: When metals are required in a ultra pure state, the zone refining method is used. The principleemployed states that the impurities, which lower the melting point of ... remain preferentially dissolved in the liquid phase and purer metal will emerge in the solid phase.

Ultra purification of a metal is done by : (1) slugging (2) zone melting (3) smelting (4) leaching

Description : Ultra purification of a metal is done by : (1) slugging (2) zone melting (3) smelting (4) leaching

Last Answer : zone melting

Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Description : Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Last Answer : Answer: Option B

High copper amalgam lasts longer than low copper amalgam because of:** A. Increased compressive strength B. Increased corrosion resistance C. High creep D. Increased tensile strength E. Decreased setting expansion

Description : High copper amalgam lasts longer than low copper amalgam because of:**  A. Increased compressive strength  B. Increased corrosion resistance  C. High creep  D. Increased tensile strength  E. Decreased setting expansion 

Last Answer : A. Increased compressive strength 

Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Description : Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Last Answer : A) Soundness*

In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Last Answer : (C) Appreciable strain hardening is produced

Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its fatigue strength (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Description : Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its ... (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Last Answer : (C) Cold working of a metal decreases its fatigue strength

Fatigue strength of a material increases by (A) Having notches in the specimen (B) Rise in temperature (C) Under stressing the specimen (D) Having scratches on the surface

Description : Fatigue strength of a material increases by (A) Having notches in the specimen (B) Rise in temperature (C) Under stressing the specimen (D) Having scratches on the surface

Last Answer : (C) Under stressing the specimen

Tumbling is the process of improving the __________ of the materials/parts. (A) Surface finish (B) Fatigue limit (C) Creep limit (D) Surface cleanliness

Description : Tumbling is the process of improving the __________ of the materials/parts. (A) Surface finish (B) Fatigue limit (C) Creep limit (D) Surface cleanliness

Last Answer : Option D

List the steps involved in slugging process

Description : List the steps involved in slugging process

Last Answer : i) Sieving ii) Weighing iii) Blending iv) Slugging v) Screening vi) Blending vii) Compression Or. Drug + Excipients → Blending → Slugging(formation of big size tablet) → Screening → Blending → Compression.

When the steel bars are embedded in concrete. The concrete after setting, adheres to the surface of the bars and thus resist any force that tends to pull or push this road. The intensity of this adhesive force is called. (a) Bond stress (b) Shear stress (c) Compressive stress (d) All of these

Description : When the steel bars are embedded in concrete. The concrete after setting, adheres to the surface of the bars and thus resist any force that tends to pull or push this road. The intensity of this adhesive force is called. (a) Bond stress (b) Shear stress (c) Compressive stress (d) All of these

Last Answer : (a) Bond stress

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Description : The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Last Answer : b) Fatigue

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. (a) Fatigue Failure (b) Fracture (c) None of the listed (d) Nipping

Last Answer : (a) Fatigue Failure

Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Description : Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Last Answer : (B) Tensile

What's the point of sterilizing a tool when lancing an abscess?

Description : What's the point of sterilizing a tool when lancing an abscess?

Last Answer : You don’t want to introduce new bacteria or otherwise bad stuff into the wound. You already have one kind of infection, do you really want another in the same sore area?

Enlist press operations . Explain lancing and piercing.

Description : Enlist press operations . Explain lancing and piercing. 

Last Answer : Press Operations: [1] Cutting or Shearing Operations: Blanking, Punching, Piercing, Notching, perforating, trimming, shaving, slitting, lancing. [2] Bending Operation: Angle bending [3] Forming ... clearance is provided on the die. Figure shows punch and die set for piercing. 

Why does metal have a high compressive strength?

Description : Why does metal have a high compressive strength?

Last Answer : Need answer

The compressive strength of cement should not be less than about 110Kg/cm2 after three days & not less than 170Kg/cm2 after seven days. The fineness of an ordinary cement as determined by turbidimetric method should be about __________ cm2 /gm. (A) 800 (B) 1600 (C) 4000 (D) 8500

Description : The compressive strength of cement should not be less than about 110Kg/cm2 after three days & not less than 170Kg/cm2 after seven days. The fineness of an ordinary cement as determined by turbidimetric method should be about __________ cm2 /gm. (A) 800 (B) 1600 (C) 4000 (D) 8500

Last Answer : (B) 1600

Slugging in a fluidised bed can be avoided by using (A) Tall narrow vessel (B) Deep bed of solids (C) Shallow beds of solids and proper choice of particle size (D) Very large particles

Description : Slugging in a fluidised bed can be avoided by using (A) Tall narrow vessel (B) Deep bed of solids (C) Shallow beds of solids and proper choice of particle size (D) Very large particles

Last Answer : (C) Shallow beds of solids and proper choice of particle size

Slugging occurs in a fluidised bed, if the bed is (A) Narrow (B) Deep (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Slugging occurs in a fluidised bed, if the bed is (A) Narrow (B) Deep (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

While normal carburising and nitriding surface treatments increase fatigue strength, excessive treatment may decrease the fatigue strength. Why ?

Description : While normal carburising and nitriding surface treatments increase fatigue strength, excessive treatment may decrease the fatigue strength. Why ?

Last Answer : .Normal carburising/nitriding treatments increase volume due to phase transformation at Surface and introduce residual compressive surface stress and thus increase the fatigue strength. By excessive treatment the ... develop in the regions of high tensile stress and lead to early fatigue failure.

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

While Normal Carburizing And Nit Riding Surface Treatments Increase Fatigue Strength, Excessive Treatment May Decrease The Fatigue Strength. Why?

Description : While Normal Carburizing And Nit Riding Surface Treatments Increase Fatigue Strength, Excessive Treatment May Decrease The Fatigue Strength. Why?

Last Answer : Normal carburizes/nits riding treatments increases volume due to phase transformation at the surface and introduce residual compressive surface stress and thus increases fatigue strength. By excessive treatment, the ... in the regions of the high tensile stress and lead o early fatigue failure.

Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Description : Cotter joint is employed when the members are subjected to which sort of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the above

Last Answer : c) Axial tensile or compressive

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Description : Parallel fillet welds are under  Shear and bending stresses  Compressive and torsion shear stresses  Tensile and compressive stresses  None

Last Answer :  None

Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Description : Cotter joint is used when the members are subjected to which type of stresses? a) Axial tensile b) Axial compressive c) Axial tensile or compressive d) None of the mentioned

Last Answer : c) Axial tensile or compressive

In the analysis, all the principal stresses are assumed as a. Shear stresses b. Compressive stresses c. Tensile stresses d. None

Description : In the analysis, all the principal stresses are assumed as a. Shear stresses b. Compressive stresses c. Tensile stresses d. None

Last Answer : c. Tensile stresses

Nature of the three principal stresses is a. Firstly All tensile b. Secondly All compressive c. Thirdly All shear d. None

Description : Nature of the three principal stresses is a. Firstly All tensile b. Secondly All compressive c. Thirdly All shear d. None

Last Answer : a. Firstly All tensile

The equations for principal stresses are valid only when (a)σ x and σ y are both tensile (b) σ x is compressive and σ y is tensile (c) σ x is tensile and σ y is compressive (d) None

Description : The equations for principal stresses are valid only when (a)σ x and σ y are both tensile (b) σ x is compressive and σ y is tensile (c) σ x is tensile and σ y is compressive (d) None

Last Answer : (a)σ x and σ y are both tensile

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

A short column 20 cm × 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on the column, should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Description : A short column 20 cm 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2 , the Safe load on ... should not exceed (A) 4120 kg (B) 41,200 kg (C) 412,000 kg (D) None of these

Last Answer : Answer: Option B

A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc /2) (d - n/3) (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Description : A singly reinforced beam has breadth b, effective depth d, depth of neutral axis n and critical neutral axis n1. If fc and ft are permissible compressive and tensile stresses, the moment to resistance of the beam, is (A) bn (fc ... (B) Atft (d - n/3) (C) ½ n1 (1 - n1/3) cbd² (D) All the above

Last Answer : Answer: Option D