The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen

The value of Poison’s ratio depends upon
(a) Nature of load, tensile or compressive
(b) Magnitude of load
(c) Material of the test specimen
(d) Dimensions of the test specimen
by

1 Answer

Answer :

(c) Material of the test specimen
by

Related questions

The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Last Answer : B

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (a) One-half of the radius (b) One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Last Answer : (c) One-quarter of the radius

A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Last Answer : (c) Shear considerations only

Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Description : Which of the following is a dimensionless quantity? (a) Shear stress (b) Poison’s ratio (c) Strain (d) Both (b) and (c)

Last Answer : (d) Both (b) and (c)

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. (a) Due to bending (b) Due to tensile (c) Due to fatigue (d) None of the listed

Last Answer : (b) Due to tensile

The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive

Description : The type of stress induced in a closed coiled helical tension spring is a. tensile b. compressive c. torsional shear d. tensile and compressive

Last Answer : c. torsional shear

A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Description : A thin spherical shell under internal pressure will fail under a. Maximum shear stress b. Principal compressive stress c. Principal tensile stress d. None

Last Answer : c. Principal tensile stress

It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting

Last Answer : b) Tensile

When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Description : When a shaft is subjected to a twisting moment, every cross-section of the shaft will be under (a) Tensile stress (b) Compressive stress (c) Shear stress (d) All of these

Last Answer : c) Shear stress

In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero

Description : In a simply supported beam loaded with U.D.L over the whole section, the bending stress is …………. at top and ………….. at bottom. (a) Compressive, tensile (b) Tensile, compressive (c) Tensile, zero (d) Compressive, zero

Last Answer : (a) Compressive, tensile

Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Description : Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Last Answer : (a) σt = σc

Tensile and compressive stresses in a beam of un-symmetrical section are (a) σt = σc (b) σt =0 (c) σc =0 (d) None

Description : Tensile and compressive stresses in a beam of un-symmetrical section are (a) σt = σc (b) σt =0 (c) σc =0 (d) None

Last Answer : (d) None

Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Description : Tensile and compressive stresses in a beam of symmetrical section are (a) σt = σc (b) σt > σc (c) σt < σc (d) None

Last Answer : (a) σt = σc

When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Description : When a bar is subjected to increase in temperature and its deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) None of the above

Last Answer : (b) Compressive

When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Description : When a bar is subjected to a change of temperature and its longitudinal deformation is prevented, the stress induced in the bar is (a) Tensile (b) Compressive (c) Shear (d) Temperature

Last Answer : (d) Temperature

The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleabilityy

Last Answer : (c) Ductility

A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Description : A column has moment of inertia about X-X and Y-Y axis as follows IXX=4234.4 mm4 IYY=236.3 mm4 This column will buckle about (a) X-X axis (b) Y-Y axis (c) It depends upon the applied load (d) None of these

Last Answer : (b) Y-Y axis

Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Description : Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Last Answer : Answer: Option A

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Description : Nature of stresses produced in buckling and bending are (a) Same (b) Different (c) Only tensile (d) None

Last Answer : (a) Same

A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Description : A short, hollow cast iron cylinder with a wall thickness of 1 cm is to carry a compressive load of 10 tonnes. If the working stress in compression is 800 kg/cm2, the outside diameter of the cylinder should not be less than a) 0.5cm b) 5 cm c) 2.5cm d) 4.5 cm

Last Answer : b) 5 cm

For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Description : For keeping the stress wholly compressive the load may be applied on a circular column anywherewithin a concentric circle of diameter (a) d/2 (b) d/3 (c) d/4 (d) d/8

Last Answer : (c) d/4

If a cohesive soil specimen is subjected to a vertical compressive load, the inclination of the cracks to the horizontal is (A) 90° (B) 45° (C) 22.5° (D) 0

Description : If a cohesive soil specimen is subjected to a vertical compressive load, the inclination of the cracks to the horizontal is (A) 90° (B) 45° (C) 22.5° (D) 0

Last Answer : (B) 45°

For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft c. Strength of both the shafts in equal d. Strength of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Description : For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of ... of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Last Answer : b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft

A complementary shear stress is equal in magnitude and opposite in rotational tendency of an applied (a) Tensile stress (b) Compressive stress (c) Shear stress (d) None

Description : A complementary shear stress is equal in magnitude and opposite in rotational tendency of an applied (a) Tensile stress (b) Compressive stress (c) Shear stress (d) None

Last Answer : (c) Shear stress

A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Description : A close coiled spring under axial load produces (a) Bending stresses (b) Shear stresses (c) Tensile stresses (d) None

Last Answer : (b) Shear stresses

The range within which a load can be applied on a rectangular column, to avoid any tensile stress,is (a) One-half of the base (b) One-fifth of the base (c) One-fourth of the base (d) One-fifth of the base

Description : The range within which a load can be applied on a rectangular column, to avoid any tensile stress,is (a) One-half of the base (b) One-fifth of the base (c) One-fourth of the base (d) One-fifth of the base

Last Answer : (b) One-fifth of the base

When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Description : When a simply supported beam is loaded with a point load at the centre, the maximum tensile stress is developed on the (a) Top fibre (b) Bottom fibre (c) Neutral axis (d) None of these

Last Answer : (b) Bottom fibre

When mild steel is subjected to a tensile load, its fracture will conform to (a) Star shape (b) Granular shape (c) Cup and cone shape (d) Fibrous shape

Description : When mild steel is subjected to a tensile load, its fracture will conform to (a) Star shape (b) Granular shape (c) Cup and cone shape (d) Fibrous shape

Last Answer : (c) Cup and cone shape

The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress

Description : The stress which vary from a minimum value to a maximum value of the same nature (i.e. tensile or compressive) is called (a) repeated stress (b) yield stress (c) fluctuating stress (d) alternating stress

Last Answer : (c) fluctuating stress

Four wires of the same material and dimensions as under are stretched by a load of same magnitude separately. Which of them will be elongated maximum? (a) wire of 3m length and 1.5 mm diameter (b) wire of 1m length and 2mm diameter (c) wire of 2m length and 2mm diameter (d) wire of 1m length and 1mm diameter

Description : Four wires of the same material and dimensions as under are stretched by a load of same magnitude separately. Which of them will be elongated maximum? (a) wire of 3m length and 1.5 mm diameter (b) ... and 2mm diameter (c) wire of 2m length and 2mm diameter (d) wire of 1m length and 1mm diameter

Last Answer : Ans:(a)

Explain the laboratory procedure to determine the compressive strength of concrete cubes as per IS-516-1959 with reference to following points: i. Preparation of test specimen ii. Procedure of testing iii. Interpretation of results

Description : Explain the laboratory procedure to determine the compressive strength of concrete cubes as per IS-516-1959 with reference to following points: i. Preparation of test specimen ii. Procedure of testing iii. Interpretation of results

Last Answer : Preparation of test specimen: i. Take three cubes of 15 cm sides and apply oil to its inner surface. ii. Prepare the concrete mixture of required grade and fill it in each mould in 3 layers. ... say 23N/mm 2) than the specified grade M20, then that concrete is safe and good for construction.

The strength of a beam depends upon (a) Its section modulus (b) Permissible bending stress (c) Both (a) and (b) (d) None of these

Description : The strength of a beam depends upon (a) Its section modulus (b) Permissible bending stress (c) Both (a) and (b) (d) None of these

Last Answer : (a) Its section modulus

Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Description : Bending moment at supports in case of simply supported beam is always (a) Zero (b) Positive (c) Negative (d) Depends upon loading

Last Answer : (a) Zero

The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Description : The close-coiled helical springs ‘A’ and ‘B’ are of same material, same coil diameter, same wire diameter and subjected to same load. If the number of turns of spring ‘A’ is half that of spring ‘B’, the ratio of deflection of spring ‘A’ to spring ‘B’ is (a)1/2 (b) 1 (c) 2 (d) 4

Last Answer : (a)1/2

Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Description : Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Last Answer : (a) Ductility

Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Description : Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Last Answer : (B) Fatigue

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

The magnitude of water hammer depends upon the (A) Elastic properties of the pipe material (B) Elastic properties of the liquid flowing through the pipe (C) Speed at which the valve is closed (D) All of the above

Description : The magnitude of water hammer depends upon the (A) Elastic properties of the pipe material (B) Elastic properties of the liquid flowing through the pipe (C) Speed at which the valve is closed (D) All of the above

Last Answer : Answer: Option D

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose endsare hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2, the permissible maximumcrippling load will be (a) 1.288 tonnes (b) 12.88 (c) 128.8 tonnes (d) 288.0

Last Answer : (b) 12.88

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Description : Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Last Answer : [ A ] Consistency

Nature of the three principal stresses is a. Firstly All tensile b. Secondly All compressive c. Thirdly All shear d. None

Description : Nature of the three principal stresses is a. Firstly All tensile b. Secondly All compressive c. Thirdly All shear d. None

Last Answer : a. Firstly All tensile

Which of the following is not a basic type of strain? (a)Compressive strain (b)Shear strain (c)Area strain (d)Volume strain

Description : Which of the following is not a basic type of strain? (a)Compressive strain (b)Shear strain (c)Area strain (d)Volume strain

Last Answer : (c)Area strain

Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Description : Magnitude of shear stress induced in a shaft due to applied torque varies from a. Maximum at centre to zero at circumference. b. Maximum at centre to minimum (not-zero) at circumference. c. Zero at centre to maximum at circumference. d. Minimum (not zero) at centre to maximum at circumference.

Last Answer : c. Zero at centre to maximum at circumference.

For bending equation to be valid, radius of curvature of the beam after bending should be a. Equal to its transverse dimensions b. Infinity c. Very large compared to its transverse dimensions d. Double its transverse dimensions

Description : For bending equation to be valid, radius of curvature of the beam after bending should be a. Equal to its transverse dimensions b. Infinity c. Very large compared to its transverse dimensions d. Double its transverse dimensions

Last Answer : c. Very large compared to its transverse dimensions

Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Last Answer : C. Axial tensile or compressive load

Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Description : Cotter joints is used for transforming........... A. Axial compressive load B. Axial tensile load C. Axial tensile or compressive load D. Twisting load

Last Answer : C. Axial tensile or compressive load