A transformer: a. Works on A.C. only b. Works on D.C only c. Works on A.C. and D.C d. Has no hysteresis loss

A transformer:
a. Works on A.C. only b. Works on D.C only
c. Works on A.C. and D.C d. Has no hysteresis loss
by

1 Answer

Answer :

a. Works on A.C. only
by

Related questions

The loss of energy over each A.C cycle magnetization and demagnetization of transformer, is called: a. Magnetization loss b. Hysteresis loss c. Demagnetization loss d. energy loss

Description : The loss of energy over each A.C cycle magnetization and demagnetization of transformer, is called: a. Magnetization loss b. Hysteresis loss c. Demagnetization loss d. energy loss

Last Answer : c. Demagnetization loss

Materials subjected to rapid reversal of magnetism should have (a) large area oiB-H loop (b) high permeability and low hysteresis loss (c) high co-ercivity and high retentivity (d) high co-ercivity and low density

Description : Materials subjected to rapid reversal of magnetism should have (a) large area oiB-H loop (b) high permeability and low hysteresis loss (c) high co-ercivity and high retentivity (d) high co-ercivity and low density

Last Answer : (b) high permeability and low hysteresis loss

The energy required to magnetize and demagnetize is called a) Saturation b) Retentivity c) Coercivity d) Hysteresis lossThe energy required to magnetize and demagnetize is called a) Saturation b) Retentivity c) Coercivity d) Hysteresis loss

Description : The energy required to magnetize and demagnetize is called a) Saturation b) Retentivity c) Coercivity d) Hysteresis loss

Last Answer : d) Hysteresis loss

What is hysteresis loss in transformer?

Description : What is hysteresis loss in transformer?

Last Answer : The magneto motive force or mmf applied in the transformer core is alternating. For every cycle due to this domain reversal, there will be extra work done. For this reason, there will be a consumption of electrical energy which is known as Hysteresis loss of transformer.

69 In case there are burrs on the edges of the laminations of the transformer, it is likely to result in A. Vibrations B. Noise C. Higher eddy currents loss D. Higher hysteresis loss

Description : 69 In case there are burrs on the edges of the laminations of the transformer, it is likely to result in A. Vibrations B. Noise C. Higher eddy currents loss D. Higher hysteresis loss

Last Answer : C. Higher eddy currents loss

43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Description : 43 The purpose of providing an iron core in a transformer is to A.Provide support to windings B. Reduce hysteresis loss C. decrease the reluctance of the magnetic path D. reduce eddy current losses

Last Answer : C. Decrease the reluctance of the magnetic path

39 Which loss is not common between a transformer and rotating machines? A. Eddy current loss B. Copper loss C. Windage loss D. Hysteresis loss

Description : 9 Which loss is not common between a transformer and rotating machines? A. Eddy current loss B. Copper loss C. Windage loss D. Hysteresis loss

Last Answer : A. Eddy current loss

24 Transformer cores are laminated in order to A. simplify its construction B. minimise eddy current loss C. reduce cost D. reduce hysteresis loss

Description : 24 Transformer cores are laminated in order to A. simplify its construction B. minimise eddy current loss C. reduce cost D. reduce hysteresis loss

Last Answer : B. Minimise eddy current loss

17. Which type of loss is not common to transformer and rotating machines? A. Eddy current loss B. Copper loss C. Hysteresis loss D. Windage loss

Description : 17. Which type of loss is not common to transformer and rotating machines? A. Eddy current loss B. Copper loss C. Hysteresis loss D. Windage loss

Last Answer : D. Windage loss

Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability

Description : Which of the following properties is not necessarily desirable in the material for transformer core? A. Mechanical strength B. Low hysteresis loss C. High thermal conductivity D. High permeability

Last Answer : C) high thermal conductivity

A 220/440 V, 50 Hz, 5 KVA, single phase transformer operates on 220V, 40Hz supply with secondary winding open circuited. Then (A) Both eddy current and hysteresis losses decreases. (B) Both eddy current and hysteresis losses increases. (C) Eddy current loss remains the same but hysteresis loss increases. (D) Eddy current loss increases but hysteresis loss remains the same.

Description : A 220/440 V, 50 Hz, 5 KVA, single phase transformer operates on 220V, 40Hz supply with secondary winding open circuited. Then (A) Both eddy current and hysteresis losses decreases. (B) Both ... same but hysteresis loss increases. (D) Eddy current loss increases but hysteresis loss remains the same.

Last Answer : (A) Both eddy current and hysteresis losses decreases.

A transformer at 25 Hz develops 20 W hysteresis loss and 50 W eddy current loss. If the applied voltage and

Description : A transformer at 25 Hz develops 20 W hysteresis loss and 50 W eddy current loss. If the applied voltage and frequency are doubled, the new core losses are (A) 140 W (B) 180 W (C) 240 W (D) 480 W

Last Answer : A transformer at 25 Hz develops 20 W hysteresis loss and 50 W eddy current loss. If the applied voltage and frequency are doubled, the new core losses are 240 W

Hysteresis loss in a transformer depends upon: -

Description :  Hysteresis loss in a transformer depends upon: -  a) both voltage and frequency b) voltage alone c) frequency alone d) none of these

Last Answer :  Hysteresis loss in a transformer depends upon: - both voltage and frequency

In n-p-n transistor, p works as ________ (a) Collector (b) emitter (c) base (d) any of above

Description : In n-p-n transistor, p works as ________ (a) Collector (b) emitter (c) base (d) any of above

Last Answer : c) base

To couple a coaxialline toa parallel-wire line,itisbesttouse a a. slotted line b.balun c. directional coupler d. quarter-wave transformer

Description : To couple a coaxialline toa parallel-wire line,itisbesttouse a a. slotted line b.balun c. directional coupler d. quarter-wave transformer

Last Answer : b.balun

What is a current transformer and voltage transformer?*

Description : What is a current transformer and voltage transformer?*

Last Answer : In electrical engineering, a current transformer (CT) is used for measurement of electric currents. Current transformers, together with voltage transformers (VT) (potential transformers (PT)), ... transformers are commonly used in metering and protective relays in the electrical power industry.

Why are motor ratings given in KW and that of alternator and transformer given in KVA?

Description : Why are motor ratings given in KW and that of alternator and transformer given in KVA?

Last Answer : kW is the output mechanical power of a motor and is expressed in kW. kVA is the net (apparent) power input to the transformer. This input power is the output + losses. kW = kVA x system power factor

Which of the following converts electric energy into mechanical energy: a. Transformer b. DC generator c. Motor d. AC generator

Description : Which of the following converts electric energy into mechanical energy: a. Transformer b. DC generator c. Motor d. AC generator

Last Answer : d. AC generato

The induced current in transformer which produced in the direction perpendicular to flux, is known as: a. Conventional current b. electronic current c. Perpendicular current d. Eddy current

Description : The induced current in transformer which produced in the direction perpendicular to flux, is known as: a. Conventional current b. electronic current c. Perpendicular current d. Eddy current

Last Answer : c. Perpendicular current

The most common source of AC voltage is: a. motor b. generator c. cell d. transformer

Description : The most common source of AC voltage is: a. motor b. generator c. cell d. transformer

Last Answer : c. cell

A transformer steps down 220V to 40 volts. If the secondary turns are 40 then primary turns will be: a. 20 b. 40 c. 120 d. 220

Description : A transformer steps down 220V to 40 volts. If the secondary turns are 40 then primary turns will be: a. 20 b. 40 c. 120 d. 220

Last Answer : d. 220V

The application of mutual induction is: a. TV b. Radio c. Transformer d. Motor

Description : The application of mutual induction is: a. TV b. Radio c. Transformer d. Motor

Last Answer : c. Transformer

An ideal transformer always obeys the law of conservation of........: a. energy b. momentum c. charge d. Flux

Description : An ideal transformer always obeys the law of conservation of........: a. energy b. momentum c. charge d. Flux

Last Answer : b. momentum

Turn ratio of a transformer is 5. If 220 V AC is applied to its primary coil, voltage in the secondary coil will be: a. 44V b. 4.4 V c. 220V d. 1100V

Description : Turn ratio of a transformer is 5. If 220 V AC is applied to its primary coil, voltage in the secondary coil will be: a. 44V b. 4.4 V c. 220V d. 1100V

Last Answer : c. 220V

To construct a step down transformer, the condition is: a. Ns > Np b. Np > Ns c. Np = Ns d. Np . Ns = 1

Description : To construct a step down transformer, the condition is: a. Ns > Np b. Np > Ns c. Np = Ns d. Np . Ns = 1

Last Answer : c. Np = Ns

Explain the electrical characteristics of transformer.

Description : Explain the electrical characteristics of transformer.

Last Answer : Transformer electrical characteristics: Area of primary and secondary conductors, Apri and Asec: Winding loss Pw: Flux density and core loss: Leakage inductance: ... transformer span. The rise in temperature may breakdown insulation which may cause failure of the transformer.

is efficiency of transformer is greater than electrical machine and why?

Last Answer : The efficiency of transformer is Greater than electrical Machine because there is no rotational losses in transformer and there is no air gap losses in transformer so losses is less in transformer compare to electrical machine so efficiency is higher in case of transformer.

A hysteresis motor works on the principle of?

Last Answer : A hysteresis motor works on the principle of hysteresis loss.

42 The efficiency of a transformer will be maximum when A. copper losses = hysteresis losses B. Hysteresis losses = eddy current losses C. Eddy current losses = copper losses D. Copper losses = iron losses

Description : 42 The efficiency of a transformer will be maximum when A. copper losses = hysteresis losses B. Hysteresis losses = eddy current losses C. Eddy current losses = copper losses D. Copper losses = iron losses

Last Answer : D. Copper losses = iron losses

7 The main advantage of auto transformer over a two winding transformer is A. Hysteresis losses are reduced B. Saving in winding material C. Copper losses are negligible D. Eddy losses are totally eliminated

Description : 7 The main advantage of auto transformer over a two winding transformer is A. Hysteresis losses are reduced B. Saving in winding material C. Copper losses are negligible D. Eddy losses are totally eliminated

Last Answer : A) hysteresis losses is reduced

The hysteresis and eddy current losses of a single phase transformer working on 200 V, 50 Hz

Description : The hysteresis and eddy current losses of a single phase transformer working on 200 V, 50 Hz supply are Ph and Pe respectively. The percentage decrease in these when operated on a 160 V, 40 Hz supply are   (a) 32, 36 (b) 20, 36 (c) 25, 50 (d) 40, 80 

Last Answer : The hysteresis and eddy current losses of a single phase transformer working on 200 V, 50 Hz supply are Ph and Pe respectively. The percentage decrease in these when operated on a 160 V, 40 Hz supply are 20, 36

Loss comparisons between fusionsplices andmechanicalsplices are a. 1:10 b. 10:1 c. 20:1 d. 1:20

Description : Loss comparisons between fusionsplices andmechanicalsplices are a. 1:10 b. 10:1 c. 20:1 d. 1:20

Last Answer : a. 1:10

Thegroundwave eventuallydisappears, as onemoves awayfromthetransmitter, because of a. interference from the sky wave b. loss of line-of-sight conditions c. maximumsingle-hop distance limitation d. tilting

Description : Thegroundwave eventuallydisappears, as onemoves awayfromthetransmitter, because of a. interference from the sky wave b. loss of line-of-sight conditions c. maximumsingle-hop distance limitation d. tilting

Last Answer : d. tilting

What is Hysteresis Loss ?

Description : What is Hysteresis Loss ?

Last Answer : We know that transformers are made of electromagnetic materials like iron , ferrite cores etc. Now when this transformer is repeatedly magnetized and de-magnetized by an alternating current, the ... , generators , fans. However, generators and transformers try to control this hysteresis loss.

What is Hysteresis Loss ?

Description : What is Hysteresis Loss ?

Last Answer : Hysteresis Loss Wh = nh / B ^ 1.6 max fv

Which of the following losses is/are present in every direct current generator armature? A. Winding copper loss B. Core eddy current loss C. Magnetic hysteresis loss D. All of the above.

Description : Which of the following losses is/are present in every direct current generator armature? A. Winding copper loss B. Core eddy current loss C. Magnetic hysteresis loss D. All of the above.

Last Answer : Answer: D

Materials that retain a large part of their magnetization, after the magnetizing force is removed, are said to have _____________. A. low hysteresis loss B. high flux density C. high permanence D. high permeability

Description : Materials that retain a large part of their magnetization, after the magnetizing force is removed, are said to have _____________. A. low hysteresis loss B. high flux density C. high permanence D. high permeability

Last Answer : Answer: C

As an armature revolves within a magnetic field, friction is developed between the rotated magnetized particles as they pass through each magnetization cycle. This results in ____________. A. copper loss B. eddy-current loss C. hysteresis loss D. armature reaction

Description : As an armature revolves within a magnetic field, friction is developed between the rotated magnetized particles as they pass through each magnetization cycle. This results in ____________. A. copper loss B. eddy-current loss C. hysteresis loss D. armature reaction

Last Answer : Answer: C

The heating of conductors as a result of resistance in a distribution circuit causes a power loss expressed as _____________. A. line droop B. line loss C. IR drop D. hysteresis

Description : The heating of conductors as a result of resistance in a distribution circuit causes a power loss expressed as _____________. A. line droop B. line loss C. IR drop D. hysteresis

Last Answer : Answer: B

Mention the factors on which hysteresis loss depends?

Description : Mention the factors on which hysteresis loss depends?

Last Answer : (i) Quality and amount of iron in the core (ii) Flux density and (iii) Frequency.

How to minimize Hysteresis loss?

Description : How to minimize Hysteresis loss?

Last Answer : By using good magnetic material. By using less value of Magnetic flux density

Straight silicon steel (containing Si from 0.5 to 5%) because of their low hysteresis loss and high magnetic permeability are used for electrical appliances. Which of the following electrical appliances made of silicon steel contains maximum percentage of silicon (about 4%)? (A) Armature of small motors/generators (B) Generators and small motors (C) Induction motors (D) High frequency transformers

Description : Straight silicon steel (containing Si from 0.5 to 5%) because of their low hysteresis loss and high magnetic permeability are used for electrical appliances. Which of the following electrical ... /generators (B) Generators and small motors (C) Induction motors (D) High frequency transformers

Last Answer : (D) High frequency transformers

The loss of strength in compression which occurs, when there is a gain of strength in tension due to over loading is called (A) Bauschinger effect (B) Hooke's effect (C) Hysteresis (D) Relaxation

Description : The loss of strength in compression which occurs, when there is a gain of strength in tension due to over loading is called (A) Bauschinger effect (B) Hooke's effect (C) Hysteresis (D) Relaxation

Last Answer : (A) Bauschinger effect

70] Silicon steel used in laminations mainly reduces A. Hysteresis loss B. Eddy current losses C. Copper loss D. All of the above

Description : 70] Silicon steel used in laminations mainly reduces A. Hysteresis loss B. Eddy current losses C. Copper loss D. All of the above

Last Answer : A. Hysteresis loss

Hysteresis loss least depends on (A) Frequency. (B) Magnetic field intensity. (C) Volume of the material. (D) Grain orientation of material.

Description : Hysteresis loss least depends on (A) Frequency. (B) Magnetic field intensity. (C) Volume of the material. (D) Grain orientation of material.

Last Answer : (D) Grain orientation of material.

A ferrite core has less eddy current loss than an iron core because ferrites have (A) High resistance. (B) Low resistance. (C) Low permeability. (D) High hysteresis.

Description : A ferrite core has less eddy current loss than an iron core because ferrites have (A) High resistance. (B) Low resistance. (C) Low permeability. (D) High hysteresis.

Last Answer : (A) High resistance.

The armature of a dc machine is laminated to reduce: (A) Eddy current loss (B) Hysteresis loss (C) copper losses (D) friction and windage losses

Description : The armature of a dc machine is laminated to reduce: (A) Eddy current loss (B) Hysteresis loss (C) copper losses (D) friction and windage losses

Last Answer : Ans: A Thinner the laminations, greater is the resistance offered to the induced e.m.f., smaller the current and hence lesser the I2R loss in the core.

State the factors affecting hysteresis loss.

Description : State the factors affecting hysteresis loss.

Last Answer : i) Flux density ii) Frequency iii) Volume of the magnetic material iv) Nature of magnetic material

If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?

Description : If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be?

Last Answer : If the area of hysteresis loop of a material is large, the hysteresis loss in this material will be large.