What is the best method for bending aluminum square tubing while keeping a tight radius and minimum distortion?

What is the best method for bending aluminum square tubing while keeping a tight radius and minimum distortion?
by

1 Answer

Answer :

Buy a pipe bender from a hardware store. Then fill the pipe with water and freeze it, this will stop it form compressing.
by

Related questions

What are the pros and cons of becoming a welder?

Description : What are the pros and cons of becoming a welder?

Last Answer : answer:It's a good craft and well paid when there is work. If you're into the building trades, it is a good choice. On the other hand, you don't do much more than weld all the time. And if ... working construction you might be in a ditch or outdoors in bad weather. But that's true of a lot of jobs.

What is the simplest way to get accurate measurements for stairs and guardrail?

Description : What is the simplest way to get accurate measurements for stairs and guardrail?

Last Answer : A Square is the quickest way…

Explain with sketch electron beam welding.

Description : Explain with sketch electron beam welding. 

Last Answer : Electron Beam Welding Process In EBW process, the heat is generated when the electron beam impinges on work piece. As the high velocity electron beam strikes the surfaces to be welded, their kinetic ... material that is directly in the path is melted which when solidifies form the joint. 

State the four advantages of MIG welding.

Description : State the four advantages of MIG welding.  

Last Answer : Four advantages of MIG welding: 1. High quality welds can be produced much faster. 2. Flux is not used there is no chance for the entrapment of slag in the weld metal resulting in high quality ... of metals and alloys. 5. Least expensive and highly economic. 6. Little or no post welds cleaning.

List two special feature of welding transformer.

Description : List two special feature of welding transformer.

Last Answer : Special features of welding transformer: i) It is a step down transformer that reduces the source voltage to a voltage desired according to the demands of the welding process. ii) Having large primary turns and less ... V ii) Secondary voltage - 40 to 60 V iii) Secondary current - 200 to 600 A

Welding Defects

Description : Welding Defects 

Last Answer : Welding Defects  Welding defects Explanation and causes 1. Cracks Cracks occur when localized stresses exceed the ultimate tensile strength of material. These stresses are developed due to shrinkage ... Too fast a travel, Bad welding technique, Too great a heat build-up.

State the applications of TIG welding.

Description : State the applications of TIG welding.

Last Answer : The applications of TIG welding are as follows: 1. Mostly used to weld aluminum and aluminum alloys. 2. It is used to weld stainless steel, carbon base alloy, copper base alloy, nickel base alloy etc. 3. It is used to welding dissimilar metals. 4. It is mostly used in aerospace industries.

Describe with a neat diagram, the process of any one type of electric welding.

Description : Describe with a neat diagram, the process of any one type of electric welding. 

Last Answer : Methods of electric welding :  1. Resistance welding  i Butt welding  ii Spot welding  iii Seam welding  iv Projection welding  2. Arc Welding  i Carbon arc welding  ii ... as copper, iron etc. The electric arc effectively concentrate heat on the surfaces it is desired to join.

Compare between Resistance welding and Arc welding on any six points.

Description : Compare between Resistance welding and Arc welding on any six points.

Last Answer : Sr.No Parameters Resistance Welding Arc Welding 1 Type of welding Plastic/Pressure/Non-fusion welding Fusion/Non pressure welding 2 Principle of heat developed Heat ... It is suitable for mass production It is suitable for heavy job, maintenance and repair work

Give any three features and any two applications of welding transformer.

Description : Give Any Three Features And Any Two Applications Of Welding Transformer.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

For arc welding current range is usually

Description : For arc welding current range is usually  (1) 10 to 15 A (2) 30 to 40 A (3) 50 to 100 A (4) 100 to 350 A

Last Answer : For arc welding current range is usually 100 to 350 A

Spot welding is used for

Description : Spot welding is used for (1) Thin metal (3) Castings only (2) Rough and irregular surface (4) Thick sections

Last Answer : Spot welding is used for Thin metal

Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :

Description : Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  (C) Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

Last Answer : Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  ... Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

The electrode rod used for welding uses a coating on it

Description : The electrode rod used for welding uses a coating on it 

Last Answer : The electrode rod used for welding uses a coating on it  to give a vapour to serve as a shielding gas to protect the weld area from atmospheric contamination and to provide slag to protect the welded area

The supply for arc welding is :

Description : The supply for arc welding is : 

Last Answer : The supply for arc welding is : Low voltage, high current ac or dc voltage

Welding generator will have?

Last Answer : Welding generator will have lap winding.

What's the best way to make a barb fitting that's a bit small for the tubing give a water-tight fit? [See details].

Description : What's the best way to make a barb fitting that's a bit small for the tubing give a water-tight fit? [See details].

Last Answer : answer:I'm thinking teflon plumber's tape might do the job. Would that work? It seems like it would give you a nice seal, if understand what you are trying to do. I'm not good at math at all, really, ... is. I did that calculation on google; not by myself. That's the only way I could do the math.

Aluminum Tubing ?

Description : Aluminum Tubing ?

Last Answer : form_title= Aluminum Tubing form_header= Make DIY projects a snap with aluminum tubing How much aluminum tubing do you need?*= _ [50] How are using the aluminum tubing? *= _ [50] Do you want to buy the tubing online?*= () Yes () No

Refraction is the a. Bending of light waves b. Reflection of light waves c. Distortion of light waves d. Diffusion of light waves

Description : Refraction is the a. Bending of light waves b. Reflection of light waves c. Distortion of light waves d. Diffusion of light waves

Last Answer : a. Bending of light waves

A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Description : A transmission shaft subjected to pure bending moment should be designed on the basis of (A) Maximum principal stress theory (B) Maximum shear stress theory (C) Distortion energy theory (D) Goodman or Soderberg diagrams

Last Answer : (A) Maximum principal stress theory

Refraction is the ∙ A. bending of light ∙ B. reflection of light waves ∙ C. distortion of light waves ∙ D. diffusion of light waves

Description : Refraction is the ∙ A. bending of light ∙ B. reflection of light waves ∙ C. distortion of light waves ∙ D. diffusion of light waves

Last Answer : A. bending of light

Refraction is the ∙ a. Bending of light waves ∙ b. Reflection of light waves ∙ c. Distortion of light waves ∙ d. Diffusion of light waves

Description : Refraction is the ∙ a. Bending of light waves ∙ b. Reflection of light waves ∙ c. Distortion of light waves ∙ d. Diffusion of light waves

Last Answer : a. Bending of light waves

Proper storage battery maintenance includes ____________. A. keeping connections tight and casing surfaces clean B. making sure electrolyte level is below the separator plates C. insulating the terminals with naval jelly D. maintaining a high charging rate at all times

Description : Proper storage battery maintenance includes ____________. A. keeping connections tight and casing surfaces clean B. making sure electrolyte level is below the separator plates C. insulating the terminals with naval jelly D. maintaining a high charging rate at all times

Last Answer : Answer: A

These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Description : These bends are caused by excessive pressure and tension and generally occur while fiber are bent during handling or installation. ∙ A. microbending ∙ B. macrobending ∙ C. constant-radius bending ∙ D. kinks

Last Answer : C. constant-radius bending

The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Description : The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Last Answer : a) Ellipse

The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Description : The region of safety for biaxial stresses is of which shape in the case of maximum distortion energy theorem. a) Ellipse b) Circle c) Rectangle d) Square

Last Answer : a) Ellipse

Could a piece of tubing be twisted into a Möbius strip?

Description : Could a piece of tubing be twisted into a Möbius strip?

Last Answer : No, because the Möbius strip is 2-D. The Möbius strip is produced by giving a half twist to a plane, the strip, and connecting the ends of the plane. The strip inside the twisted tube would be 2-D, but the tube remains 3-D.

where can I buy hydraulic steel tubing per ams5520 or AMS 5520. Or per the new updated spec?

Description : where can I buy hydraulic steel tubing per ams5520 or AMS 5520. Or per the new updated spec?

Last Answer : Need Answer

In a lab what would i use to measure a 10 cm length of dialysis tubing?

Description : In a lab what would i use to measure a 10 cm length of dialysis tubing?

Last Answer : A meter ruler or a tape measure

Why we never disconnect the tubing from the gas cock without first turning the gas off?

Description : Why we never disconnect the tubing from the gas cock without first turning the gas off?

Last Answer : If the gas is not turned off first, on removing the tubing, gas will escape - very dangerous.

Why we never disconnect the tubing from the gas cock without first turning the gas off?

Description : Why we never disconnect the tubing from the gas cock without first turning the gas off?

Last Answer : If the gas is not turned off first, on removing the tubing, gas will escape - very dangerous.

How is gas introduced into the glass tubing used in neon signs?

Description : How is gas introduced into the glass tubing used in neon signs?

Last Answer : Neon tubes are capped off by two glass electrodes that have wirepassing from outside to inside. One of these electrodes hastubulation - a small tube which remains as a passage from outsideto inside. Tubulations are ... is then heated and as it is pulled it suchinward to make the tube's own seal.

What is the best tool for cutting copper tubing?

Description : What is the best tool for cutting copper tubing?

Last Answer : Copper tubing is best cut with a straight saw, ideally diamond tipped for the cleanest cut.

Copper Tubing?

Description : Copper Tubing?

Last Answer : form_title= Copper Tubing form_header= Have the supplies you need for all of your home improvement tasks. How much tubing do you need?*= _ [50] Will the tubing be used for liquids?*= () Yes () No Please describe the project in detail.*= _ [50]

How to Cut Stainless Steel Tubing?

Description : How to Cut Stainless Steel Tubing?

Last Answer : If you are doing a building project at home or elsewhere, chances are at some point you're going to have to use stainless steel tubing. Stainless steel tubing is a very resilient material to use for projects ... curved blades over the part of the tube you want to cut. Use a pencil to mark this spot

How to Determine the Most Suitable Tubing Material?

Description : How to Determine the Most Suitable Tubing Material?

Last Answer : The tubing material for any application depends on the nature application. Suppose if the tube is exposed to different types of conditions the SS tube would be applicable and same would be for bearing much pressure. There are several tubing material in market each with its own ability.

What is the maximum allowable temperature that should be used on heat-shrinkable tubing?

Description : What is the maximum allowable temperature that should be used on heat-shrinkable tubing?

Last Answer : 300º F

To get minimum harmonic distortion in the output, a 34 to 34 cyclo-converter requires :

Description : To get minimum harmonic distortion in the output, a 3-Ф to 3-Ф cyclo-converter requires :  (A) 12 SCRs (B) 18 SCRs (C) 36 SCRs (D) 72 SCRs

Last Answer : To get minimum harmonic distortion in the output, a 3-Ф to 3-Ф cyclo-converter requires : 36 SCRs

If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of elasticity stress and the depth of the neutral axis at section, then (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Description : If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of  elasticity stress and the depth of the neutral axis at section, then  (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Last Answer : (C) M/I = E/R = E/Y

Type of bend that occurs as a result of differences in thermal contraction rates between the core and the cladding material. ∙ A. Macrobending ∙ B. Microbending ∙ C. Quad bending ∙ D. Constant-radius bending

Description : Type of bend that occurs as a result of differences in thermal contraction rates between the core and the cladding material. ∙ A. Macrobending ∙ B. Microbending ∙ C. Quad bending ∙ D. Constant-radius bending

Last Answer : B. Microbending

The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Description : The product of the tangential force acting on the shaft and radius of shaft known as (a) Torsional rigidity (b) Flexural rigidity (c) Bending moment (d) Twisting moment

Last Answer : (d) Twisting moment

For bending equation to be valid, radius of curvature of the beam after bending should be a. Equal to its transverse dimensions b. Infinity c. Very large compared to its transverse dimensions d. Double its transverse dimensions

Description : For bending equation to be valid, radius of curvature of the beam after bending should be a. Equal to its transverse dimensions b. Infinity c. Very large compared to its transverse dimensions d. Double its transverse dimensions

Last Answer : c. Very large compared to its transverse dimensions

What is the product of sectional modulus and allowable bending stress called as? a. Moment of inertia b. Moment of rigidity c. Moment of resistance d. Radius of gyration

Description : What is the product of sectional modulus and allowable bending stress called as? a. Moment of inertia b. Moment of rigidity c. Moment of resistance d. Radius of gyration

Last Answer : c. Moment of resistance

Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) Cement should be mixed by hand in order to maintain uniformity (C) Concrete mix should be stored in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° ± 2°C

Description : Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) ... in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° 2°C

Last Answer : Answer: Option D

square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?

Description : square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?

Last Answer : 10001/999900

A square column carries a load P at the centroid of one of the quarters of the square. If a is the side of the main square, the combined bending stress will be (A) p/a² (B) 2p/a² (C) 3p/a² (D) 4p/a²

Description : A square column carries a load P at the centroid of one of the quarters of the square. If a is the  side of the main square, the combined bending stress will be  (A) p/a² (B) 2p/a² (C) 3p/a² (D) 4p/a²

Last Answer : (C) 3p/a²

The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Description : The cross sections of the beams of equal length are a circle and a square whose permissible bending stress is same under same maximum bending. The ratio of their flexural weights is, (A) 1.118 (B) 1.338 (C) 1.228 (D) 1.108

Last Answer : (A) 1.118

The areas of cross-section of a square beam and a circular beam subjected to equal bending moments, are same. (A) Circular beam is more economical (B) Square beam is more economical (C) Both the beams are equally strong (D) Both the beams are equally economical

Description : The areas of cross-section of a square beam and a circular beam subjected to equal bending  moments, are same.  (A) Circular beam is more economical  (B) Square beam is more economical  (C) Both the beams are equally strong  (D) Both the beams are equally economical 

Last Answer : (B) Square beam is more economical 

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

If is the net upward pressure on a square footing of side for a square column of side , the maximum bending moment is given by (A) B.M = pb (c - a)/4 (B) B.M = pb (b - a)²/4 (C) B.M = pb (b - a)²/8 (D) B.M = pb (b + a)/8

Description : If is the net upward pressure on a square footing of side for a square column of side , the maximum bending moment is given by (A) B.M = pb (c - a)/4 (B) B.M = pb (b - a)²/4 (C) B.M = pb (b - a)²/8 (D) B.M = pb (b + a)/8

Last Answer : Answer: Option C