Why is the OCV capped at voltage setting? a) To save electricity b) To prevent exploding of the consumable c) Allow smooth transition into welding voltage range d) To reduce the risk of fatality

Why is the OCV capped at voltage setting?  
a) To save electricity b) To prevent exploding of the consumable  c) Allow smooth transition into welding voltage range d) To reduce the risk of fatality
by

1 Answer

Answer :

c) Allow smooth transition into welding voltage range
by

Related questions

Consumable electrodes are used in the __________ welding. (A) Gas (B) Arc (C) Thermit (D) Resistance

Description : Consumable electrodes are used in the __________ welding. (A) Gas (B) Arc (C) Thermit (D) Resistance

Last Answer : (B) Arc

Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat

Description : Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat

Last Answer : c) To prevent the possible risk of cracking

What is the maximum OCV allowable to initiate an arc when using A. C current? a) 1000V b) 10V c) 90V d) 900V

Description : What is the maximum OCV allowable to initiate an arc when using A. C current? a) 1000V b) 10V c) 90V d) 900V

Last Answer : c) 90V

What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Description : What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Last Answer : c) 10-12V

Vehicle tyres are inflated properly – (1) to ensure smooth running. (2) to allow the vehicle to take more load. (3) to avoid skidding and to minimize friction (4) to go fast and save fuel.

Description : Vehicle tyres are inflated properly – (1) to ensure smooth running. (2) to allow the vehicle to take more load. (3) to avoid skidding and to minimize friction (4) to go fast and save fuel.

Last Answer : (3) to avoid skidding and to minimize friction Explanation: Under-inflated tyres create more friction with the road, increasing fuel consumption by up to ten per cent and are prone to skidding on ... or slippery surfaces. Low pressures also lead to premature wear and risk of tyre blowout or bulging.

Vehicle tyres are inflated properly (1) to ensure smooth running. (2) to allow the vehicle to take more load. (3) to avoid skidding and to minimise friction (4) to go fast and save fuel.

Description : Vehicle tyres are inflated properly (1) to ensure smooth running. (2) to allow the vehicle to take more load. (3) to avoid skidding and to minimise friction (4) to go fast and save fuel.

Last Answer : to avoid skidding and to minimise friction 

What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant information c) None if the tensile strength of the consumables is the same as the approved one d) Change the electrode for the correct type and continue welding

Description : What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant ... the same as the approved one d) Change the electrode for the correct type and continue welding

Last Answer : b) Report the incident and record all relevant information

t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved qualification to cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Description : t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved ... cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Last Answer : a) Never

What is indicated by gradual blackening at the ends of component 'C' shown in the illustration? EL-0081 A. The unit is in danger of exploding. B. The tube is nearing the end of its useful life. C. The circuit voltage is too high. D. The circuit current is too high.

Description : What is indicated by gradual blackening at the ends of component 'C' shown in the illustration? EL-0081 A. The unit is in danger of exploding. B. The tube is nearing the end of its useful life. C. The circuit voltage is too high. D. The circuit current is too high.

Last Answer : Answer: B

Addition of stabiliser during PVC manufacture is done to (A) Improve its impact strength (B) Improve its elasticity (C) Reduce the melt viscosity & glass transition temperature (D) Prevent its thermal degradation

Description : Addition of stabiliser during PVC manufacture is done to (A) Improve its impact strength (B) Improve its elasticity (C) Reduce the melt viscosity & glass transition temperature (D) Prevent its thermal degradation

Last Answer : (D) Prevent its thermal degradation

Which sport has never had a fatality occur during competition?

Description : Which sport has never had a fatality occur during competition?

Last Answer : answer:Intercollegiate Tiddly-winks. I can’t think of any other sport anywhere that hasn’t had at least one death.

What is the verb form of fatality?

Description : What is the verb form of fatality?

Last Answer : There is no verb form of fatal

Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent short circuiting. B. only be connected to multimeter on the ammeter setting C. be short circuited D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Description : Before servicing the device indicated as 'A' in panels #1 and #3 of the illustration, the device labeled 'CT' must __________. EL-0003 A. have the disconnected leads taped to prevent ... D. have one lead grounded to discharge static electricity for the prevention of damage to electronic components

Last Answer : Answer: C

Which of the following methods is most commonly used to reduce information risk? a. Allow all users to prepare the statements. b. Allow users to verify information. c. Have the financial statements audited. d. Users share information risk with management.

Description : Which of the following methods is most commonly used to reduce information risk? a. Allow all users to prepare the statements. b. Allow users to verify information. c. Have the financial statements audited. d. Users share information risk with management.

Last Answer : Have the financial statements audited

Which of the following methods is most commonly used to reduce information risk? a. Allow users to verify information. b. Allow all users to prepare the statements. c. Users share information risk with management. d. Have the financial statements audited

Description : Which of the following methods is most commonly used to reduce information risk? a. Allow users to verify information. b. Allow all users to prepare the statements. c. Users share information risk with management. d. Have the financial statements audited

Last Answer : Have the financial statements audited

ask-public MacGyvers: I need to open an old fashioned bottle-capped bottle, not a twist off, no bottle opener, can you help?

Description : ask-public MacGyvers: I need to open an old fashioned bottle-capped bottle, not a twist off, no bottle opener, can you help?

Last Answer : I see so much shit listed up above and I ask you this one question: Do you have a counter top in your bathroom? If so here is what you do. 1. Place edge of bottle cap on the edge of counter top ... can be found on motel TV's. PS- I hope they are the Orange Aranciatas. They are sooooo good. xoxoxo

Did Hugh Grant get his teeth capped or have work done?

Description : Did Hugh Grant get his teeth capped or have work done?

Last Answer : Yes definite caps

5’-Terminus of mRNA molecule is capped with (A) Guanosine triphosphate (B) 7-Methylguanosine triphophate (C) Adenosine triphosphate (D) Adenosine diphosphate

Description : 5’-Terminus of mRNA molecule is capped with (A) Guanosine triphosphate (B) 7-Methylguanosine triphophate (C) Adenosine triphosphate (D) Adenosine diphosphate

Last Answer : Answer : B

A bottle filled with previously moistened mustard seeds and water was screw capped tightly and kept in a corner. It blew up suddenly after about half an hour. The phenomenon involved is (a) diffusion (b) imbibition (c) osmosis (d) DPD.

Description : A bottle filled with previously moistened mustard seeds and water was screw capped tightly and kept in a corner. It blew up suddenly after about half an hour. The phenomenon involved is (a) diffusion (b) imbibition (c) osmosis (d) DPD.

Last Answer : b) imbibition

The deleterious materials present in the aggregate (a) Prevent normal hydration of cement (b) Reduce the strength and durability of concrete. (c) Modify the setting action and cause efloresecence. (d) All of the above

Description : The deleterious materials present in the aggregate (a) Prevent normal hydration of cement (b) Reduce the strength and durability of concrete. (c) Modify the setting action and cause efloresecence. (d) All of the above

Last Answer : (d) All of the above

The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider

Description : The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider

Last Answer : d) The weld width would be wider

When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Description : When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Last Answer : Answer: A

When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Description : When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Last Answer : Answer: A

fected biological sample. Antiretroviral treatment will achieve the following in him: A. Reduce the risk of contracting HIV infection B. Rule out the possibility of contracting HIV infection C. Prevent appearance of HIV seropositivity but not HIV infection in him D. None of the above

Description : fected biological sample. Antiretroviral treatment will achieve the following in him: A. Reduce the risk of contracting HIV infection B. Rule out the possibility of contracting HIV infection C. Prevent appearance of HIV seropositivity but not HIV infection in him D. None of the above

Last Answer : A. Reduce the risk of contracting HIV infection

In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of the laminar film (C) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Description : In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of ... ) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Last Answer : (B) When the roughness projections are much smaller than the thickness of the laminar film

Transition length for turbulent flow in smooth pipe is equal to __________ times the pipe diameter. (A) 0.5 (B) 5 (C) 50 (D) 500

Description : Transition length for turbulent flow in smooth pipe is equal to __________ times the pipe diameter. (A) 0.5 (B) 5 (C) 50 (D) 500

Last Answer : (C) 50

Why are people so sentimental about killing consumable animals?

Description : Why are people so sentimental about killing consumable animals?

Last Answer : They think the methane from all their shit is destroying the earth. It scares them.

Mark the incorrect option a) The articles of stock such as plant and machinery, furniture and fixture are classed as “Dead stock” b) Consumable and perishable articles come under the term “Stores” c) Both the A and B d) None of these

Description : Mark the incorrect option a) The articles of stock such as plant and machinery, furniture and fixture are classed as “Dead stock” b) Consumable and perishable articles come under the term “Stores” c) Both the A and B d) None of these

Last Answer : d) None of these

A restaurant purchased two new ovens. These ovens are an example of which type of industrial product? A)major equipment B)accessory equipment C)consumable supply D)process material

Description : A restaurant purchased two new ovens. These ovens are an example of which type of industrial product? A)major equipment B)accessory equipment C)consumable supply D)process material

Last Answer : A)major equipment

Gap stores sell primarily what type of products? A)Convenience B)Shopping C)Consumable D)Nondurable E)Specialty

Description : Gap stores sell primarily what type of products? A)Convenience B)Shopping C)Consumable D)Nondurable E)Specialty

Last Answer : B)Shopping

Products that are used directly in the production of a final product but are not easily identifiable are categorised as A)accessory products. B)component parts. C)consumable supplies. D)assembly components. E)process materials

Description : Products that are used directly in the production of a final product but are not easily identifiable are categorised as A)accessory products. B)component parts. C)consumable supplies. D)assembly components. E)process materials

Last Answer : E)process materials

Large tools and machines used in a production process for a considerable length of time are classified as A)major equipment. B)accessory equipment. C)component parts. D)raw materials. E)consumable supplies.

Description : Large tools and machines used in a production process for a considerable length of time are classified as A)major equipment. B)accessory equipment. C)component parts. D)raw materials. E)consumable supplies.

Last Answer : A)major equipment

GDP is defined as (a) The market value of all goods and services produced in the domestic economy during the year ; (b) Current value of all the capital goods produced in the country. ; (c) Sum of goods and services exported during the year. ; (d) All the capital goods and consumable goods produced and sold during the year

Description : GDP is defined as (a) The market value of all goods and services produced in the domestic economy during the year ; (b) Current value of all the capital goods produced in the country. ; (c) ... during the year. ; (d) All the capital goods and consumable goods produced and sold during the year

Last Answer : (a) The market value of all goods and services produced in the domestic economy during the year ; 

Autotransformer starters or compensators are sometimes used with polyphase induction motors to _____________. A. reduce the voltage applied to the motor during the starting period B. increase the voltage for 'across-the-line starting' C. provide a backup means of voltage regulation for emergency starting D. allow the voltage to be either stepped up or down, depending on the application, to ensure full torque

Description : Autotransformer starters or compensators are sometimes used with polyphase induction motors to _____________. A. reduce the voltage applied to the motor during the starting period B. increase the voltage for ' ... to be either stepped up or down, depending on the application, to ensure full torque

Last Answer : Answer: A

A low-voltage protection circuit is used in electric motor starting equipment to _____________. A. trip circuit contactors when the motor overspeeds due to low voltage B. trip circuit contactors when the motor develops a short circuit due to low voltage C. allow the motor to restart automatically on restoration of voltage without manually resetting D. prevent the motor from restarting automatically on restoration of voltage

Description : A low-voltage protection circuit is used in electric motor starting equipment to _____________. A. trip circuit contactors when the motor overspeeds due to low voltage B. trip circuit ... voltage without manually resetting D. prevent the motor from restarting automatically on restoration of voltage

Last Answer : Answer: D

What is your trick or cheat to make poached eggs without them exploding?

Description : What is your trick or cheat to make poached eggs without them exploding?

Last Answer : Just drop the egg into just barely boiling water. Crack your egg into a bowl or onto a saucer. Bring a pan of water filled at least 5cm deep to a simmer. Tip the egg into the pan. Cook for 2 ... leave the pan for 8-10 minutes. Lift the egg out with a slotted spoon and drain it on kitchen paper.

Hate groups are exploding in number in the USA, but the KKK is dwindling. Why?

Description : Hate groups are exploding in number in the USA, but the KKK is dwindling. Why?

Last Answer : The KKK has a really bad public image. People switch to lesser known hate groups so their views are less likely to be looked down upon by the rest of society.

Where can i buy an exploding dye packet to catch a thief?

Description : Where can i buy an exploding dye packet to catch a thief?

Last Answer : See this question.

What imaginative uses could you find for an exploding dye pack ?

Description : What imaginative uses could you find for an exploding dye pack ?

Last Answer : I have four children. (Two teenage sons, a five year old daughter and a husband.) We would make good use of it. trust me!

Exploding dye packs?

Description : Exploding dye packs?

Last Answer : I don’t think that this will fit your needs for the following reasons: 1. I’m pretty sure that they’re only sold in bulk—like big, big bulk and 2. They require a radio transmitter thingy to trigger the explosion, which is probably a bit more of a financial outlay than you’re willing to make.

As the universe expands faster and faster and reaches the speed of light, it crosses it. Then it will stop, accelerate further or its speed will become steady. Is everything slowing down or exploding?

Description : That's what I was thinking.

Last Answer : If so, I think the rate of expansion will be constant. Although there is already a theory that the universe is not expanding.

What are the answers to exploding sun challenge khan acedamy?

Description : What are the answers to exploding sun challenge khan acedamy?

Last Answer : Need answer

What is the name for a exploding star?

Description : What is the name for a exploding star?

Last Answer : That's called a supernova.

Is fireworks exploding a physical change or chemical change?

Description : Is fireworks exploding a physical change or chemical change?

Last Answer : I guess it is a chemical change as the exploded fireworks cantbe regained back which is possible in a physical change and not ina chemical change.

'Super nova' is – (1) a comet (2) an asteroid (3) an exploding Star (4) a black hole

Description : 'Super nova' is – (1) a comet (2) an asteroid (3) an exploding Star (4) a black hole

Last Answer : (3) an exploding Star Explanation: A supernova is a stellar explosion that is more energetic than a nova. During this short interval a supernova can radiate as much energy as the Sun is expected to emit over its ... star's material at a velocity of up to 30,000 km/s (10% of the speed of light).

‘Super nova’ is (1) a comet (2) an asteroid (3) an exploding Star (4) a black hole

Description : ‘Super nova’ is (1) a comet (2) an asteroid (3) an exploding Star (4) a black hole

Last Answer : an exploding Star

Setting out of Lemniscate transition curves, is done with (A) Perpendicular offsets (B) Radial offsets (C) Deflection angles (D) Polar deflection angles

Description : Setting out of Lemniscate transition curves, is done with (A) Perpendicular offsets (B) Radial offsets (C) Deflection angles (D) Polar deflection angles

Last Answer : Answer: Option D

In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter’s output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum quantization error. (C) Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Description : In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter's output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum ... Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Last Answer : (B) Reduce the maximum quantization error.