What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant information c) None if the tensile strength of the consumables is the same as the approved one d) Change the electrode for the correct type and continue welding

What course of action should be taken upon finding a welder using incorrect shielding gas?  
a) Allow welding to proceed if the workmanship is good  
b) Report the incident and record all relevant information
c) None if the tensile strength of the consumables is the same as the approved one  
d) Change the electrode for the correct type and continue welding
by

1 Answer

Answer :

b) Report the incident and record all relevant information
by

Related questions

t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved qualification to cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Description : t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved ... cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Last Answer : a) Never

Which of the following would not be required to be checked before welding? a) The welding consumables b) The welder qualification c) Calibration of the welding equipment d) The workshop humidity

Description : Which of the following would not be required to be checked before welding? a) The welding consumables b) The welder qualification c) Calibration of the welding equipment d) The workshop humidity

Last Answer : d) The workshop humidity

Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department

Description : Who has the responsibility of ensuring the welder is using the correct polarity during welding? a) The welder and the welding inspector b) Store man and the welder c) Welding Engineer d) The Q/A department

Last Answer : a) The welder and the welding inspector

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable

Description : Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable

Last Answer : a) The welding engineer

What information should be recorded as a minimum, on a completed production weld? a) Size and type of electrode and b) Welding supervisor’s name c) Welder’s Identification, date and weld number d) Welding inspectors name

Description : What information should be recorded as a minimum, on a completed production weld? a) Size and type of electrode and b) Welding supervisor’s name c) Welder’s Identification, date and weld number d) Welding inspectors name

Last Answer : c) Welder’s Identification, date and weld number

Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification/Code? a) Anyone can select the welds as its just a random choice b) The welder as he knows which welds are likely to produce the least defects c) This will be referenced in the inspection and test plan d) Nobody, as welding is always carried out to a high standard the use of percentage NDT is of no real value

Description : Who should select the specific welds for NDT, to cover the 10% contractual percentage required by the specification/Code? a) Anyone can select the welds as its just a random choice b) The welder ... welding is always carried out to a high standard the use of percentage NDT is of no real value

Last Answer : c) This will be referenced in the inspection and test plan

Retroviruses are so-named because their reverse transcriptase _____. a. reverses the flow of genetic information by stimulating information to proceed from RNA to DNA. b. reverses the normal multiplication of cells from a low rate to a high rate. c. reverses the ability of viruses to associate with cells. d. reverses the action of drugs on viruses and allows them to continue multiplying in living cells.

Description : Retroviruses are so-named because their reverse transcriptase _____. a. reverses the flow of genetic information by stimulating information to proceed from RNA to DNA. b. reverses the normal ... the action of drugs on viruses and allows them to continue multiplying in living cells.

Last Answer : a. reverses the flow of genetic information by stimulating information to proceed from RNA to DNA.

Who is responsible for site safety? a) Site Quality Engineer b) Welding Supervisor c) An approved safety engineer d) Everyone

Description : Who is responsible for site safety? a) Site Quality Engineer b) Welding Supervisor c) An approved safety engineer d) Everyone

Last Answer : d) Everyone

After the celebration of the successful milestone completion, a project manager will often do which of the following? Select one: a. Continue to increase the intensity of the project to achieve the next milestone. b. Continue to follow the exact same project plan that helped the team achieve the milestone. c. Allow the team to reflect on finding new ways of approaching the project work. d. Select an upcoming key event and designate it as the next milestone. e. Stretch the goals of the project team, making them more tough and rigorous.

Description : After the celebration of the successful milestone completion, a project manager  will often do which of the following? Select one: a. Continue to increase the intensity of the project to achieve the ... milestone. e. Stretch the goals of the project team, making them more tough and rigorous.

Last Answer : c. Allow the team to reflect on finding new ways of approaching the project work.

welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Description : welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Last Answer : arch welding is a more stable form of welding. it get hotter and creates a stronger bond

Which word best describes the narrator based on this excerpt I had a different suspicion a darker one that I dared not voice but it decided my course of action I would proceed with my experiment.?

Description : Which word best describes the narrator based on this excerpt I had a different suspicion a darker one that I dared not voice but it decided my course of action I would proceed with my experiment.?

Last Answer : Another answer is objective!

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

If, while searching a computer for evidence of a specific crime, evidence of a new, Unrelated crime is discovered, the best course of action is: a. Abandon the original search, and pursue the new line of investigation b. Continue with the original search but also pursue the new inquiry c. Stop the search and obtain a warrant that addresses the new inquiry d. Continue with the original search, ignoring the new information

Description : If, while searching a computer for evidence of a specific crime, evidence of a new, Unrelated crime is discovered, the best course of action is: a. Abandon the original search, and ... a warrant that addresses the new inquiry d. Continue with the original search, ignoring the new information

Last Answer : c. Stop the search and obtain a warrant that addresses the new inquiry

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

The HIV titer of an AIDS patient was found to be reduced but still detectable after 6 months of tripple drug anti-HIV therapy. The best course of action in this patient is: A. Continue the same 3 drugs for another 3 months B. Replace all 3 drugs with a set of another 3 drugs C. Replace 2 drugs and continue one previously used drug D. Replace one drug and continue two previously used drugs

Description : The HIV titer of an AIDS patient was found to be reduced but still detectable after 6 months of tripple drug anti-HIV therapy. The best course of action in this patient is: A. Continue the ... 2 drugs and continue one previously used drug D. Replace one drug and continue two previously used drugs

Last Answer : B. Replace all 3 drugs with a set of another 3 drugs

Pick up the incorrect statement (A) The cross-sectional area of the welded member is effective (B) A welded joint develops strength of its parent metal (C) Welded joints provide rigidity (D) Welding takes more time than riveting

Description : Pick up the incorrect statement (A) The cross-sectional area of the welded member is effective (B) A welded joint develops strength of its parent metal (C) Welded joints provide rigidity (D) Welding takes more time than riveting

Last Answer : (D) Welding takes more time than riveting

Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded) (C) In spot welding, two pieces to be joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Last Answer : (D) Mild steel sheet cannot be spot welded

Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Description : Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Last Answer : (A) Electrode size

Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Description : Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Last Answer : (B) Prevent electrode from contamination

Material of construction of the electrode used in the electric resistance welding is (A) Stainless steel (B) Graphite (C) Copper (D) Steel

Description : Material of construction of the electrode used in the electric resistance welding is (A) Stainless steel (B) Graphite (C) Copper (D) Steel

Last Answer : Option C

The electrode rod used for welding uses a coating on it

Description : The electrode rod used for welding uses a coating on it 

Last Answer : The electrode rod used for welding uses a coating on it  to give a vapour to serve as a shielding gas to protect the weld area from atmospheric contamination and to provide slag to protect the welded area

Why is the OCV capped at voltage setting? a) To save electricity b) To prevent exploding of the consumable c) Allow smooth transition into welding voltage range d) To reduce the risk of fatality

Description : Why is the OCV capped at voltage setting? a) To save electricity b) To prevent exploding of the consumable c) Allow smooth transition into welding voltage range d) To reduce the risk of fatality

Last Answer : c) Allow smooth transition into welding voltage range

The degree of protection by ground wire depends upon the a. Arcing angle b. Shielding angle c. Power factor d. All of above

Description : The degree of protection by ground wire depends upon the a. Arcing angle b. Shielding angle c. Power factor d. All of above

Last Answer : The degree of protection by ground wire depends upon the a. Arcing angle b. Shielding angle c. Power factor d. All of above

A staff nurse was found charting blood glucose result without actually doing the procedure. What is the appropriate initial action of the senior nurse? A. Write and submit an explanation and reprimand as necessary B. Go on leave without pay C. Write an incident report D. Explain to the patient

Description : A staff nurse was found charting blood glucose result without actually doing the procedure. What is the appropriate initial action of the senior nurse? A. Write and submit an explanation and reprimand as necessary B. Go on leave without pay C. Write an incident report D. Explain to the patient

Last Answer : A. Write and submit an explanation and reprimand as necessary

Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and 40,000 psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Description : Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and ... psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Last Answer : b) The hub thickness at the welding end and 40,000 psi yield strength

In welder qualification testing of 45mm plates, why are side bends used instead of root and face bends? a) They are easier to produce b) The testing equipment cannot handle thick root/face bends c) Root defects are not important for welder qualification d) They give more accurate indications

Description : In welder qualification testing of 45mm plates, why are side bends used instead of root and face bends? a) They are easier to produce b) The testing equipment cannot handle thick root/face bends c) Root defects are not important for welder qualification d) They give more accurate indications

Last Answer : d) They give more accurate indications

Who has the final responsibility of sentencing and accepting a weld on completion? a) The contractor’s inspector b) Site manager c) The welder d) The client’s inspector or certifying authority

Description : Who has the final responsibility of sentencing and accepting a weld on completion? a) The contractor’s inspector b) Site manager c) The welder d) The client’s inspector or certifying authority

Last Answer : d) The client’s inspector or certifying authority

Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Description : Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Last Answer : Answer: Option A

The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Last Answer : B

The divisional supdt may sanction up to Rs ____ in each case for purchase of equipments and consumables connected with computer and other equipments. a) 400/- b) 1500/- c) 5000/- d) 2500/

Description : The divisional supdt may sanction up to Rs ____ in each case for purchase of equipments and consumables connected with computer and other equipments. a) 400/- b) 1500/- c) 5000/- d) 2500/

Last Answer : c) 5000/

In web search, finding a large number of documents with very little relevant information is termed: (A) poor recall (B) web crawl (C) poor precision rate (D) poor web response

Description : In web search, finding a large number of documents with very little relevant information is termed: (A) poor recall (B) web crawl (C) poor precision rate (D) poor web response 

Last Answer : (A) poor recall

Can you still get in trouble if you admit poor workmanship long after a company went bankrupt?

Description : Can you still get in trouble if you admit poor workmanship long after a company went bankrupt?

Last Answer : I think it would depend on whether someone who was affected by your lies and poor workmanship had grounds and desire to file suit and hold you responsible for any damages.

What are the types of express guarantees? 1. Design/ mechanical 2. Field workmanship 3. Common Work4. Length of service 5. a and b

Description : What are the types of express guarantees? 1. Design/ mechanical  2. Field workmanship  3. Common Work 4. Length of service  5. a and b

Last Answer : 5. a and b

Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Description : Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Last Answer : a) A reduced resistance to corrosion

Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps

Description : Which of the following uses a flat characteristic? a) MAG (GMAW) b) Oxy-fuel gas welding c) Resistance spot welding d) SAW using greater than 1000 amps

Last Answer : a) MAG (GMAW)

__________ of rubber decreases after its vulcanisation. (A) Resistance to the action of organic solvent (B) Tackiness (C) Maximum service temperature (D) Tensile strength

Description : __________ of rubber decreases after its vulcanisation. (A) Resistance to the action of organic solvent (B) Tackiness (C) Maximum service temperature (D) Tensile strength

Last Answer : (B) Tackiness

Which of following is not hearsay evidence? a) Statement of police that on basis of inquiry conducted by him that accused was not at home on night of incident b) Report of newspaper c) Report prepared on basis of information provided by officer

Description : Which of following is not hearsay evidence? a) Statement of police that on basis of inquiry conducted by him that accused was not  at home on night of incident b) Report of newspaper c) Report prepared on basis of information provided by officer

Last Answer : c) Report prepared on basis of information provided by officer

Nurse Mercy is setting up for an emergency caesarian section. The linen packs were damp although these were just taken from the sterilizer. The nurse’s appropriate action is A. Bring the linen packs back to the Central Supply section for quality control B. Change the damp linen pack C. Open the linen pack and allow to dry D. Do not use the damp linen

Description : Nurse Mercy is setting up for an emergency caesarian section. The linen packs were damp although these were just taken from the sterilizer. The nurse's appropriate action is A. Bring the linen packs back to the ... linen pack C. Open the linen pack and allow to dry D. Do not use the damp linen

Last Answer : D. Do not use the damp linen

An uncoupler of oxidative phosphorylation such as dinitrophenol (A) Inhibits electron transport and ATP synthesis (B) Allow electron transport to proceed without ATP synthesis (C) Inhibits electron transport without impairment of ATP synthesis (D) Specially inhibits cytochrome b

Description : An uncoupler of oxidative phosphorylation such as dinitrophenol (A) Inhibits electron transport and ATP synthesis (B) Allow electron transport to proceed without ATP synthesis (C) Inhibits electron transport without impairment of ATP synthesis (D) Specially inhibits cytochrome b

Last Answer : B

The minimum energy required to allow a chemical reaction to proceed is termed as the 'threshold energy '. Chemical reactions with low activation energy are: (A) Always irreversible (B) Insensitive to temperature changes (C) Mostly irreversible (D) Highly temperature sensitive

Description : The minimum energy required to allow a chemical reaction to proceed is termed as the 'threshold energy '. Chemical reactions with low activation energy are: (A) Always irreversible (B) Insensitive to temperature changes (C) Mostly irreversible (D) Highly temperature sensitive

Last Answer : (B) Insensitive to temperature changes

The emf of a primary cell depends upon the: a) Physical dimension of the cell b) Nature of the electrolyte c) Nature of the electrode d) Both (b) and (c)

Description : The emf of a primary cell depends upon the: a) Physical dimension of the cell b) Nature of the electrolyte c) Nature of the electrode d) Both (b) and (c)

Last Answer : Ans: D

(3) made cathode and a pure nickel red, the anode Explanation: Electroplating is the deposition by electrolysis of a coating of metal upon a conducting surface. The simplest system makes the object to be plated the negative electrode (cathode) or plate in a galvanic couple. Thus a spoon or other object may be connected by a wire to a plate of nickel. The process that occurs on the spoon is called reduction and, therefore, the spoon is also referred to as a cathode.

Description : (3) made cathode and a pure nickel red, the anode Explanation: Electroplating is the deposition by electrolysis of a coating of metal upon a conducting surface. The simplest system makes the object to be ... on the spoon is called reduction and, therefore, the spoon is also referred to as a cathode.

Last Answer : Which of the following is not a method of preparing oxygen? (1) Electrolysis of water (2) Fractional distillation of liquid air (3) Decomposition of potassium permanganate (4) Decomposition of manganese dioxide

A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray can of refrigerant approved for this purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray ... purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Last Answer : Answer: B

What action should be taken when, during an IFR flight in VMC, you suffer a radio failure? a. Return to the aerodrome from which you departed b. Continue flying in VMC and land as soon as possible c. Maintain your assigned altitude and land at the nearest aerodrome at which there are VMC conditions d. Continue flying at your assigned altitude and start your approach at your ETA

Description : What action should be taken when, during an IFR flight in VMC, you suffer a radio failure? a. Return to the aerodrome from which you departed b. Continue flying in VMC and land as soon ... there are VMC conditions d. Continue flying at your assigned altitude and start your approach at your ETA

Last Answer : b. Continue flying in VMC and land as soon as possible