What information should be recorded as a minimum, on a completed production weld? a) Size and type of electrode and b) Welding supervisor’s name c) Welder’s Identification, date and weld number d) Welding inspectors name

What information should be recorded as a minimum, on a completed production weld?  
a) Size and type of electrode and b) Welding supervisor’s name  c) Welder’s Identification, date and weld number d) Welding inspectors name
by

1 Answer

Answer :

c) Welder’s Identification, date and weld number
by

Related questions

Who should have access to the WPQR’S? a) NDT operators b) Inspectors only c) Welders only d) Welding Engineer

Description : Who should have access to the WPQR’S? a) NDT operators b) Inspectors only c) Welders only d) Welding Engineer

Last Answer : d) Welding Engineer

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider

Description : The welders have increased the voltage on the SAW welding set, what would be the effect on the weld appearance? a) No effect b) The weld width would be narrower c) The penetration will be increased d) The weld width would be wider

Last Answer : d) The weld width would be wider

How is preheat for tack welds during assembly and fit up determined? a) By the welders as they have extensive knowledge b) The fabrication specification/WPS will give the requirements c) The fabrication drawing will give all the information d) Any temperature will do as it is only a tack weld

Description : How is preheat for tack welds during assembly and fit up determined? a) By the welders as they have extensive knowledge b) The fabrication specification/WPS will give the requirements c) The fabrication drawing will give all the information d) Any temperature will do as it is only a tack weld

Last Answer : b) The fabrication specification/WPS will give the requirements

Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Description : Coating provided on the electrodes used in the arc welding is not expected to (A) Add alloying elements (B) Prevent electrode from contamination (C) Stabilise the arc (D) Provide protective atmosphere to weld

Last Answer : (B) Prevent electrode from contamination

Why would visual inspection of the excess weld metal at the bottom of a cross country pipeline be important? a) It is the most difficult area to weld b) It is the dirtiest part of the pipe as it is near the ground c) Welders always forget to weld the bottom d) It is the most difficult area to radiograph

Description : Why would visual inspection of the excess weld metal at the bottom of a cross country pipeline be important? a) It is the most difficult area to weld b) It is the dirtiest part of the pipe as ... ground c) Welders always forget to weld the bottom d) It is the most difficult area to radiograph

Last Answer : a) It is the most difficult area to weld

What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant information c) None if the tensile strength of the consumables is the same as the approved one d) Change the electrode for the correct type and continue welding

Description : What course of action should be taken upon finding a welder using incorrect shielding gas? a) Allow welding to proceed if the workmanship is good b) Report the incident and record all relevant ... the same as the approved one d) Change the electrode for the correct type and continue welding

Last Answer : b) Report the incident and record all relevant information

t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved qualification to cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Description : t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved ... cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Last Answer : a) Never

What does the term WPQR means? a) Weld productivity quality review b) Weld production quality requirments c) Welding procedure

Description : What does the term WPQR means? a) Weld productivity quality review b) Weld production quality requirments c) Welding procedure

Last Answer : c) Welding procedure

I'm watching welding how-to videos on the Internet. Should I be wearing a welder's helmet?

Description : I'm watching welding how-to videos on the Internet. Should I be wearing a welder's helmet?

Last Answer : Wear the helmet. I father arc welded something without a helmet because it was a real quick job. He was in agony that night. Never do it without the helmet. And you watch the arc to lay down a smooth bead.

how much do welders get paid and what is the safest welding job?

Description : how much do welders get paid and what is the safest welding job?

Last Answer : They can make 60,000-100,000 but not on the safest job safest would be working auto body

Weather date of welding is marked on weld? (i) Yes (ii) As decided by the site supervisor (iii) No* (iv) None of the above

Description : Weather date of welding is marked on weld? (i) Yes (ii) As decided by the site supervisor (iii) No* (iv) None of the above

Last Answer : (iii) No*

Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Description : Which of the following mainly decides the current to be employed is arc welding? (A) Electrode size (B) Plate thickness (C) Voltage across the arc (D) Welded portion length

Last Answer : (A) Electrode size

When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Description : When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Last Answer : b) Higher deposition rate

Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable

Description : Who determines what the correct weld preparation (root gap, root face, included angle) should be? a) The welding engineer b) The welding supervisor c) The welder will decide d) The inspector will recommend what is suitable

Last Answer : a) The welding engineer

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded) (C) In spot welding, two pieces to be joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Last Answer : (D) Mild steel sheet cannot be spot welded

Material of construction of the electrode used in the electric resistance welding is (A) Stainless steel (B) Graphite (C) Copper (D) Steel

Description : Material of construction of the electrode used in the electric resistance welding is (A) Stainless steel (B) Graphite (C) Copper (D) Steel

Last Answer : Option C

The electrode rod used for welding uses a coating on it

Description : The electrode rod used for welding uses a coating on it 

Last Answer : The electrode rod used for welding uses a coating on it  to give a vapour to serve as a shielding gas to protect the weld area from atmospheric contamination and to provide slag to protect the welded area

Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Description : Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Last Answer : c) To ensure it is suitably clean for visual inspection and NDT

do i need an actual welding table in order to be able to weld?

Description : do i need an actual welding table in order to be able to weld?

Last Answer : Need Answer

welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Description : welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Last Answer : arch welding is a more stable form of welding. it get hotter and creates a stronger bond

Quantity is not a part of the weld symbol (i)Dark circle (ii) Open circle (iii) Angle of weld (iv)Starting and stopping allowance for welding

Description : Quantity is not a part of the weld symbol (i)Dark circle (ii) Open circle (iii) Angle of weld (iv)Starting and stopping allowance for welding

Last Answer : (iv)Starting and stopping allowance for welding

Term which is not a part of the weld symbol (i) Tail (ii) Arrow (iii) Temperature of welding (iv) None

Description : Term which is not a part of the weld symbol (i) Tail (ii) Arrow (iii) Temperature of welding (iv) None

Last Answer : (iii) Temperature of welding

Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding

Description : Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding

Last Answer : (iv) Machine used in welding

Steels with high carbon equivalent have poor Weldability, because in these steels during welding (A) Carbon and other alloying elements get oxidised from the weld pool (B) Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld (C) Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld (D) Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld

Description : Steels with high carbon equivalent have poor Weldability, because in these steels during welding (A) Carbon and other alloying elements get oxidised from the weld pool (B) Excessive ferrite forms in the ... of carbon and other element occurs in the weld pool leading to poor properties of the weld

Last Answer : (C) Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld

Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Description : Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Last Answer : (B) Martensite formation

Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and 40,000 psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Description : Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and ... psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Last Answer : b) The hub thickness at the welding end and 40,000 psi yield strength

What is the testing frequency of new AT weld ? (i) Just after the welding (ii) After 7 days of welding (iii) With in the one month of welding* (iv) None of the above

Description : What is the testing frequency of new AT weld ? (i) Just after the welding (ii) After 7 days of welding (iii) With in the one month of welding* (iv) None of the above

Last Answer : iii) With in the one month of welding*

In how many time final grinding should be done of new AT weld ? (i) Just after the welding (ii) After 8 hrs of welding (iii) With in 24 hrs* (iv) None of the above

Description : In how many time final grinding should be done of new AT weld ? (i) Just after the welding (ii) After 8 hrs of welding (iii) With in 24 hrs* (iv) None of the above

Last Answer : iii) With in 24 hrs*

In how many time rough riding should be done of new AT weld ? (i) Just after the welding* (ii) After 8 hrs of welding (iii) After 24 hrs (iv) None of the above

Description : In how many time rough riding should be done of new AT weld ? (i) Just after the welding* (ii) After 8 hrs of welding (iii) After 24 hrs (iv) None of the above

Last Answer : i) Just after the welding*

After AT Welding First train is to be passed after ? (i) 20 Minutes from pouring of weld metal. (ii) 35 Minutes from pouring of weld metal. (iii) 30 Minutes from pouring of weld metal.* (iv) 25 Minutes from pouring of weld metal.

Description : After AT Welding First train is to be passed after ? (i) 20 Minutes from pouring of weld metal. (ii) 35 Minutes from pouring of weld metal. (iii) 30 Minutes from pouring of weld metal.* (iv) 25 Minutes from pouring of weld metal.

Last Answer : (iii) 30 Minutes from pouring of weld metal.*

When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°? a) They should be acceptable as the standard refers to minimum forming angle b) The bends should be considered as fail c) New bends should be produced and bent to 180° then re-examined d) They should be rejected as the angle is not close enough to be acceptable

Description : When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°? a) They should be acceptable as ... then re-examined d) They should be rejected as the angle is not close enough to be acceptable

Last Answer : c) New bends should be produced and bent to 180° then re-examined

Which of the following does an auditor least likely perform in assessing audit risk? a. Understand the economic substance of significant transactions completed by the client. b. Understand the entity and the industry in which it operates. c. Gather audit evidence in support of recorded transactions. d. Obtain an understanding of the client's system of internal contro

Description : Which of the following does an auditor least likely perform in assessing audit risk? a. Understand the economic substance of significant transactions completed by the client. b. Understand the entity ... of recorded transactions. d. Obtain an understanding of the client's system of internal contro

Last Answer : Gather audit evidence in support of recorded transactions

All of the following statements about the post-closing trial balance are correct except it a. shows that the accounting equation is in balance. b. provides evidence that the journalizing and posting of closing entries have been properly completed. c. contains only permanent accounts. d. proves that all transactions have been recorded.

Description : All of the following statements about the post-closing trial balance are correct except it a. shows that the accounting equation is in balance. b. provides evidence that the journalizing and posting ... . c. contains only permanent accounts. d. proves that all transactions have been recorded.

Last Answer : d. proves that all transactions have been recorded.

When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is complete d) Minimum preheat temperature measurement is only required if the heat input is lower than that specified in WPS

Description : When would you measure the minimum preheat temperature? a) On completion of each pass b) Immediately prior to commencing the first pass and subsequent passes c) When the welding is ... preheat temperature measurement is only required if the heat input is lower than that specified in WPS

Last Answer : b) Immediately prior to commencing the first pass and subsequent passes

The attributes of a file are. a. Name b. Identifier c. Types d. Location e. Size f. Protection g. Time, date and user identification h. Allof these

Description : The attributes of a file are. a. Name b. Identifier c. Types d. Location e. Size f. Protection g. Time, date and user identification h. Allof these

Last Answer : h. Allof these

Duties of Inspectors, R.M.S. are a) Entrusted mainly with the duties of checking the sorting work done by sections and mail offices b) Making investigations into important cases of loss, fraud etc. c) When attached to the office of Heads of Circles they are designated as Sorting Inspectors. d) All the above

Description : Duties of Inspectors, R.M.S. are a) Entrusted mainly with the duties of checking the sorting work done by sections and mail offices b) Making investigations into important cases of loss, fraud etc ... to the office of Heads of Circles they are designated as Sorting Inspectors. d) All the above

Last Answer : d) All the above

It will be the _______ duty to prepare and prescribe ____(M-53) indicating the beats of the ____attached to each head, ____in his sub-division(Including first class head offices) a) Supdt, route lists and beat maps, village postmen, sub and branch office b) Inspector’s, route lists and beat maps, postmaster , sub and branch office c) Inspector’s, route lists and beat maps, village postmen, sub and branch office d) None of these

Description : It will be the _______ duty to prepare and prescribe ____(M-53) indicating the beats of the ____attached to each head, ____in his sub-division(Including first class head offices) a) Supdt, route ... Inspector's, route lists and beat maps, village postmen, sub and branch office d) None of these

Last Answer : c) Inspector’s, route lists and beat maps, village postmen, sub and branch office

Postmaster of HO who are subordinate to the super indent, Inspectors and SP, Head clerk also report every transfer or assumption of chart to the a) Group B Officer of division b) Postmaster General c) Head of the circle d) None of these

Description : Postmaster of HO who are subordinate to the super indent, Inspectors and SP, Head clerk also report every transfer or assumption of chart to the a) Group B Officer of division b) Postmaster General c) Head of the circle d) None of these

Last Answer : c) Head of the circle

Mark the correct option a) The due mail and sorting list for PO and mail offices in communication with offices in more than one RMS Dn are prepared and supplied by the Head of the circle b) The due mail and sorting list for PO in direct communication with a mail office in one RMS Dn will be issued by the Supdt of RMS concerned c) Village sorting lists are prepared and supplied to Head, Sub and Branch office by Sub divisional Inspectors.d) All the above

Description : Mark the correct option a) The due mail and sorting list for PO and mail offices in communication with offices in more than one RMS Dn are prepared and supplied by the Head of the circle b) ... are prepared and supplied to Head, Sub and Branch office by Sub divisional Inspectors. d) All the above

Last Answer : d) All the above

The person who headed U. N. Weapons Inspectors in Iraq was—

Description : The person who headed U. N. Weapons Inspectors in Iraq was—

Last Answer : Hans Blix

___ play an important role in the development of new foods and nonfood uses. a. Bakers c. Chemists b. Butchers d. Inspectors

Description : ___ play an important role in the development of new foods and nonfood uses. a. Bakers c. Chemists b. Butchers d. Inspectors

Last Answer : c. Chemists

____ prepare pies, breads, rolls, muffins, cookies, cakes, icings and frostings, and many other foods, depending on where they work. a. Inspectors c. Butchers b. Bakers d. Chefs

Description : ____ prepare pies, breads, rolls, muffins, cookies, cakes, icings and frostings, and many other foods, depending on where they work. a. Inspectors c. Butchers b. Bakers d. Chefs

Last Answer : b. Bakers

What is the best home remedy for welders flash burn?

Description : What is the best home remedy for welders flash burn?

Last Answer : answer:Potato works great. My dad owned a welding and machine shop. I went there after school to sweep for Lego money. I got welders flash and it is horrible. My mom cut a potato in half and put them on my eyes and it worked. And welders flash is insanely painful.

What exactly are Hobart welders?

Description : What exactly are Hobart welders?

Last Answer : Welder is a tradesman who specializes in welding materials together. Welding is a process that joins materials. Hobart Welders is a brand of welding machines. And yes, they are good.

What is the validity after Refresher course for welders (TW-2)? (i) Six monyhs (ii) One year (iii) Two years.* (iv) All are wrong

Description : What is the validity after Refresher course for welders (TW-2)? (i) Six monyhs (ii) One year (iii) Two years.* (iv) All are wrong

Last Answer : (iii) Two years.*