What must be used to test an activated circuit?

What must be used to test an activated circuit?
by

1 Answer

Answer :

Approved meters or other indicating devices
by

Related questions

What must be done to a circuit before you can use an ohmmeter for testing?

Description : What must be done to a circuit before you can use an ohmmeter for testing?

Last Answer : It must be de-energized.

What conditions must be met in order to balance a bridge circuit?

Description : What conditions must be met in order to balance a bridge circuit?

Last Answer : A bridge circuit is balanced when the opposite legs of the comparing and measuring circuits exhibit the same voltage drop.

Before you connect a VOM in a circuit for an ohmmeter reading, in what condition must the circuit be?

Description : Before you connect a VOM in a circuit for an ohmmeter reading, in what condition must the circuit be?

Last Answer : De-energized

A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Description : A circuit is to be designed in which a capacitor must charge to 40 percent of the maximum charging voltage in 200 microseconds. The resistor to be used has a resistance of 40,000 ohms. What size capacitor must be used?

Last Answer : 0.1 microfarads 40% from the graph = 0.5

When the Human Resources module is activated, which areas must be addressed? a. Complement (number of workers) b. Caliber (recruitment of talent of workers) c. Training (time workers spend in training) d. Benefits (retirement planning for workers) e. a, b, and c

Description : When the Human Resources module is activated, which areas must be addressed? a. Complement (number of workers) b. Caliber (recruitment of talent of workers) c. Training (time workers spend in training) d. Benefits (retirement planning for workers) e. a, b, and c

Last Answer : e. a, b, and c

Minecraft circuit that once activated stays active until reset?

Description : Minecraft circuit that once activated stays active until reset?

Last Answer : answer:@XOIIO I didn't see this question until just now. I'm not familiar with Minecraft & I'm not entirely sure what it is, even after reading the Wikipedia article on it! For a minute I thought ... Redstone Dust in your hand, right click on the block you want it on Whatever floats your boat ~

What calibration label is used when actual measurement values must be known to use the test equipment?

Description : What calibration label is used when actual measurement values must be known to use the test equipment?

Last Answer : CALIBRATED—REFER TO REPORT.

When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Description : When measuring receiver sensitivity, what quantities must you add to the dBm reading obtained on the signal generator or test set?

Last Answer : Attenuations of the directional coupler and the connecting cable.

Is an ammeter connected in series or in parallel with the circuit under test?

Description : Is an ammeter connected in series or in parallel with the circuit under test?

Last Answer : . In series.

How is an ammeter connected to the circuit under test?

Description : How is an ammeter connected to the circuit under test?

Last Answer : In series.

The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Description : The input impedance of your test equipment should exceed the impedance of the circuit under test by what ratio?

Last Answer : 10 to 1

You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. Testing an energized circuit presents a hazard to the testing personnel. B. A faulty fuse could go undetected with the motor energized. C. Reversed polarity of the circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Description : You are using a mechanical voltage tester to check the fuses in a three-phase circuit supplying an electric motor. For which of the following reasons must the motor be stopped during the test? A. ... circuit would be indicated by the voltage tester with the circuit energized. D. All of the above.

Last Answer : Answer: B

Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The starter must be placed in the STOP position to stop the motor. C. The three line connections in the motor terminal box must be disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Description : Which of the following actions must be carried out before a voltage tester can be used to test the three line fuses to a three-phase motor? A. The fuses must be removed from the circuit. B. The ... disconnected and tagged. D. Nothing need be done as long as the motor is running under a light load.

Last Answer : Answer: B

In testing a three-phase delta winding for an open circuit using a megohmmeter, you must ______________. A. test each phase with all connections intact B. measure the voltage across the open connections while testing C. test the windings as parallel groups to avoid short circuiting D. open the delta-connections to avoid shunting the phase being tested

Description : In testing a three-phase delta winding for an open circuit using a megohmmeter, you must ______________. A. test each phase with all connections intact B. measure the voltage across the open ... groups to avoid short circuiting D. open the delta-connections to avoid shunting the phase being tested

Last Answer : Answer: D

To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws of the instrument around the insulated conductor C. connect the voltage test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Description : To properly use a hook-on-type volt/ammeter to check current flow, you must FIRST _____________. A. de-energize the circuit to allow connection of the instrument in series B. hook the jaws ... test leads to the appropriate terminals D. short the test leads and calibrate the instrument to zero

Last Answer : Answer: B

What type of flux must be used in all electrical and electronic soldering?

Description : What type of flux must be used in all electrical and electronic soldering?

Last Answer : Noncorrosive, nonconductive rosin fluxes.

Why must items to be soldered be cleaned just prior to the soldering process?

Description : Why must items to be soldered be cleaned just prior to the soldering process?

Last Answer : Solder will not adhere to dirty, greasy, or oxidized surfaces.

A waveguide bend must have what minimum radius?

Description : A waveguide bend must have what minimum radius?

Last Answer : Greater than 2 wavelengths.

When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Description : When a waveguide is terminated in a resistive load, the load must be matched to what property of the waveguide?

Last Answer : . Characteristic impedance.

For an electric field to exist at the surface of a conductor, the field must have what angular relationship to the conductor?

Description : For an electric field to exist at the surface of a conductor, the field must have what angular relationship to the conductor?

Last Answer : The field must be perpendicular to the conductors.

. What primary condition must magnetic lines of force meet in order to exist?

Description : . What primary condition must magnetic lines of force meet in order to exist?

Last Answer : Magnetic lines of force must form a continuous closed loop.

What kind of material must be used in the construction of waveguides?

Description : What kind of material must be used in the construction of waveguides?

Last Answer : Conductive material.

What safety precaution must be taken before replacing a transistor?

Description : What safety precaution must be taken before replacing a transistor?

Last Answer : The power must be removed from the circuit.

An instrument that must be calibrated in place requires what type of calibration label?

Description : An instrument thAn instrumAn instrument that must be calibrated in place requires what type of calibration label?

Last Answer : SPECIAL CALIBRATION label.

To increase the magnitude of a number by 23, you must shift the number how many times and in what direction?

Description : To increase the magnitude of a number by 23, you must shift the number how many times and in what direction?

Last Answer : Three to the left.

What logic levels must exist for the FF to be toggled by the clock?

Description : What logic levels must exist for the FF to be toggled by the clock?

Last Answer : Both J and K must be HIGH.

What condition must occur to have a change in the output of a D FF?

Description : What condition must occur to have a change in the output of a D FF?

Last Answer : A positive-going clock pulse.

For an R-S FF to change output conditions, the inputs must be in what states?

Description : For an R-S FF to change output conditions, the inputs must be in what states?

Last Answer : 1 and 0, or opposite states.

To sort a data file, what must you tell the sort program?

Description : To sort a data file, what must you tell the sort program?

Last Answer : What data field or fields to sort on.

The output of the sum point must contain information that controls what two factors of load movement in a position servo?

Description : The output of the sum point must contain information that controls what two factors of load movement in a position servo?

Last Answer : Amount and direction of rotation.

What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Description : What safety precaution must you observe when soldering or hot-wire stripping fluoroplastic insulated wire?

Last Answer : Adequate ventilation.

Why must a wiring diagram be used in conjunction with a schematic to troubleshoot a system?

Description : Why must a wiring diagram be used in conjunction with a schematic to troubleshoot a system?

Last Answer : To find the test points.

Why must cables and wires be identified?

Description : Why must cables and wires be identified?

Last Answer : To provide the technician with a means to trace the wires when troubleshooting and repairing electrical and electronic systems.

What are the two main sources of emi with which radio waves must compete?

Description : What are the two main sources of emi with which radio waves must compete?

Last Answer : Natural and man-made interference.

What three factors must be considered in the transmission of a surface wave to reduce attenuation?

Description : What three factors must be considered in the transmission of a surface wave to reduce attenuation?

Last Answer : (a) electrical properties of the terrain (b) frequency (c) polarization of the antenna

To propagate energy down an arm of a hybrid ring duplexer, the two fields at the junction of the arm and the ring must have what phase relationship? To propagate energy down an arm of a hybrid ring duplexer, the two fields at the junction of the arm and the ring must have what phase relationship?

Description : To propagate energy down an arm of a hybrid ring duplexer, the two fields at the junction of the arm and the ring must have what phase relationship?

Last Answer : 180 degrees out of phase

In addition to a flat top, what characteristics must a modulator pulse have?

Description : In addition to a flat top, what characteristics must a modulator pulse have?

Last Answer : Steep leading and trailing edges.

In addition to a flat top, what characteristics must a modulator pulse have?

Description : In addition to a flat top, what characteristics must a modulator pulse have?

Last Answer : Steep leading and trailing edges.

What must the physical length of a transmission line be if it will be operated at 15,000,000 Hz?

Description : What must the physical length of a transmission line be if it will be operated at 15,000,000 Hz?

Last Answer : . λ = 20 meters

Quality fiber-end preparation is essential for proper system operation. What properties must an optical fiber-end face have to ensure proper fiber connection?

Description : Quality fiber-end preparation is essential for proper system operation. What properties must an optical fiber-end face have to ensure proper fiber connection?

Last Answer : Be flat, smooth, and perpendicular to the fiber axis.

To perform microminiature component repair, a 2M technician must be currently certified in what area?

Description : To perform microminiature component repair, a 2M technician must be currently certified in what area?

Last Answer : Microminiature component repair.

When you replace components, identification marks must meet what requirements?

Description : When you replace components, identification marks must meet what requirements?

Last Answer : They should be readable from a single point.

The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Description : The pump signal frequency must be of what value when compared to the input signal of a simple parametric amplifier?

Last Answer : Exactly double the input frequency.

What relationship must exist between the electron beam and the traveling wave for bunching to occur in the electron beam of a twt?

Description : What relationship must exist between the electron beam and the traveling wave for bunching to occur in the electron beam of a twt?

Last Answer : The traveling wave must have a forward velocity equal to or less than the speed of the electrons in the beam.

The constant-speed electrons of an electron bunch in a reflex klystron must remain in the repeller field for what minimum time?

Description : The constant-speed electrons of an electron bunch in a reflex klystron must remain in the repeller field for what minimum time?

Last Answer : Three-quarter cycle.

When designing vacuum-tube circuits, what characteristics of tubes must be taken into consideration?

Description : When designing vacuum-tube circuits, what characteristics of tubes must be taken into consideration?

Last Answer : Differences in performance of tubes of the same type

What two preventive maintenance actions must you do regularly to increase magnetic head life and to ensure good tape recording and playback?

Description : What two preventive maintenance actions must you do regularly to increase magnetic head life and to ensure good tape recording and playback?

Last Answer : a. Keep the heads clean. b. Keep the heads demagnetized.

What precautions must be taken when sweeping a transmitting antenna?

Description : What precautions must be taken when sweeping a transmitting antenna?

Last Answer : You must ensure that power induced from any adjacent transmitting antennas does not damage your test equipment.

Before a diode will conduct, the cathode must be what polarity relative

Description : Before a diode will conduct, the cathode must be what polarity relative

Last Answer : Negative.