If current is I and voltage is V, then power P is equal to

If current is I and voltage is V, then power P is equal to
by

1 Answer

Answer :

If current is I and voltage is V, then power P is equal to V x I

by

Related questions

A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to

Last Answer : A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to 2 amps.

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

Rated power of a bulb at V voltage is P. Now, same voltage V is applied in all conditions mentioned in Column I. Match this Column I with Column II in

Description : Rated power of a bulb at V voltage is P. Now, same voltage V is applied in all conditions mentioned in Column I. Match this Column I with Column II in

Last Answer : Rated power of a bulb at V voltage is P. Now, same voltage V is applied in all conditions ... Column II in which actual total power consumed is given.

A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series ...

Description : A series R-L circuit is suddenly connected to d.c. voltage source of V volts. The current in this series circuit, just after the switch is closed, is equal to (1) Zero (2) V/L (3) V/C (4) V.L/C 

Last Answer : When is a series RLC circuit is over damped

If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -

Description : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : -  a) 15 mA b) 1.5 mA c) 10 mA d) 1 mA

Last Answer : If the rms voltage drop across a 15 kilt resistor is 16 V, the peak current through the resistor is : - 1.5 mA

The voltage phasor of a circuit is 10 ∠15° V and the current phasor is 2∠–45° A. The active and reactive...

Description : The voltage phasor of a circuit is 10 ∠15° V and the current phasor is 2∠–45° A. The active and reactive powers in the circuit are   (a) 20 2 W and 10 2 VAR (b) 10 W and 10 3 VAR (c) 5 W and 5 3 VAR (d) 10 3 W and – 10 VAR 

Last Answer : Angle between voltage and current ¢=15-(-45)=60° Cos60°=1/2  Active power =vicos¢=10×2×1/2=10watt Reactive power=visin¢=10×2×sin60°=20×√3/2=10√3

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

A three-phase synchronous motor has a terminal voltage of 460 V and a terminal current of 120 A at a power factor of 0.95 lagging, synchronous reactance of 1.68 ohm and the field current is 47 A. The field to armature mutual inductance of the synchronous motor is _____________.

Description : A three-phase synchronous motor has a terminal voltage of 460 V and a terminal current of 120 A at a power factor of 0.95 lagging, synchronous reactance of 1.68 ohm and the field current is 47 A. The field to armature mutual ... _____________.      (a). 20mH   (b). 16mH   (c). 24mH   (d). 22mH

Last Answer : 22

If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

Description : If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

Last Answer : 128 volts ,2048 watts

A 1000 V/400 V power transformer has a nominal short-circuit voltage Vsc = 40%....

Description :  A 1000 V/400 V power transformer has a nominal short-circuit voltage Vsc = 40%. Which one of the following statements is correct ?  (a) A voltage of 400 V appears across the short-circuited ... V.  (d) The primary voltage drops to 400 V, when the secondary terminals are short-circuited.

Last Answer :  A 1000 V/400 V power transformer has a nominal short-circuit voltage Vsc = 40%. Which one of the following statements is correct ? (a) A voltage of 400 V appears across the short-circuited ... 400 V. (d) The primary voltage drops to 400 V, when the secondary terminals are short-circuited.

A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W....

Description : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?  (a) 100 VAR (b) 200 VAR (c) 300 VAR (d) 400 VAR

Last Answer : A single-phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ? 400 VAR

If the load p.f. is 0.866, then the average p.f. the v-bank is

Description : If the load p.f. is 0.866, then the average p.f. the v-bank is  1. 0.886  2. 0.75  3. 0.51  4. 0.65 

Last Answer : If the load p.f. is 0.866, then the average p.f. the v-bank is 0.75 

The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:

Description : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to: A. 27.2 mA B. 59 mA C. 5.9 mA D. 590 mA

Last Answer : The amount of current flowing through a circuit with a 40 V source and 6.8 kΩ of resistance is equal to:  5.9 mA

The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage across b - d is equal to the voltage of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Last Answer : Answer: A

A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Description : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is

Last Answer : A 1000 watts heater is connected to a 240 V AC Supply. Then the current drawn by the heater is 4.166 amperes

Why Voltage x Current do not equal rated power?

Description : Why Voltage x Current do not equal rated power?

Last Answer : In an AC system power is equal to Voltage x Current x Powerfactor. Power factor is not constant and depends on the type of theload. Ideal value of the Power factor is 1, where as practicallyremains less then 1.

An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from _____________. A. one line terminal to each coil lead in succession B. one field coil to each adjacent field coil in turn C. any suitable ground to any available line lead D. any field pole to each field coil lead

Description : An open shunt field in a direct current machine may be located by connecting the field circuit to an external power source, equal to the rated field voltage or less, and tested with a voltmeter from ... C. any suitable ground to any available line lead D. any field pole to each field coil lead

Last Answer : Answer: A

Equal power factors on paralleled AC generators are maintained by an automatic _____________. A. voltage regulator B. reverse power relay C. reverse current relay D. governor control switch

Description : Equal power factors on paralleled AC generators are maintained by an automatic _____________. A. voltage regulator B. reverse power relay C. reverse current relay D. governor control switch

Last Answer : Answer: A

Van der Waals derived an expression for the ‘pressure defect’, if the observed pressure is denoted as ‘p’ and volume is denoted as ‘V’, the gas pressure in the bulk of the gas is equal to: A. p + a/V; where a: constant for the particular gas B. p + a/(V²); where a: constant for the particular gas C. p + (a × V); where a: constant for the particular gas D. p + (a × V²); where a: constant for the particular gas

Description : Van der Waals derived an expression for the pressure defect', if the observed pressure is denoted as p' and volume is denoted as V', the gas pressure in the bulk of the gas is equal to: A. p + ... a: constant for the particular gas D. p + (a V²); where a: constant for the particular gas

Last Answer : p + a/(V²); where a: constant for the particular gas

An ideal gas is taken around the cycle ABCA as shown in P-V diagram below: The work done by the gas during the cycle is equal to (A) 12 P1V1 (B) 6 P1 V1 (C) 3 P1V1 (D) P1 V1

Description : An ideal gas is taken around the cycle ABCA as shown in P-V diagram below: The work done by the gas during the cycle is equal to (A) 12 P1V1 (B) 6 P1 V1 (C) 3 P1V1 (D) P1 V1

Last Answer : (C) 3 P1V1

In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Description : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

Last Answer : In the circuit shown in Fig. 4.63, the terminal voltage of the battery is 6.0 V. Find the current I through the `18 Omega` resistor.

The current (I) and voltage (V) graphs for a given metallic wire at two different temperature `(T_(1))` and `(T_(2))` are shown in fig. It is conclude

Description : The current (I) and voltage (V) graphs for a given metallic wire at two different temperature `(T_(1))` and `(T_(2))` are shown in fig. It is conclude

Last Answer : The current (I) and voltage (V) graphs for a given metallic wire at two different temperature `(T_(1))` and `(T_( ... `T_(1)=T_(2)` D. `T_(1)gt2T_(2)`

Instantaneous voltage and instantaneoss current in an L-R circuit in AC is V=100sin (100)t and `i=10sin(100t-pi//4)`. Match the following table, `{:(,

Description : Instantaneous voltage and instantaneoss current in an L-R circuit in AC is V=100sin (100)t and `i=10sin(100t-pi//4)`. Match the following table, `{:(,

Last Answer : Instantaneous voltage and instantaneoss current in an L-R circuit in AC is V=100sin (100)t and `i=10sin(100t ... power in one cycle",(S),"None"):}`

A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Last Answer : ANSWER: Z -- 5 V/R

Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Description : Two unpedauces given by Z1 = 10 + j5 and Z2 = 8 + j9 are joined in parallel and connected across a voltage of V = 200 + j0. Calculate the circuit current and branch currents. Draw the vector diagram.

Last Answer : Solution: Given, Z1=10+j5, Z2=8+j9, V=200+j0

A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Description : A linear network has a current input 4cos(ω t + 20º)A and a voltage output 10 cos(ωt +110º) V. Determine the associated impedance.

Last Answer : Solution

Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT configuration having current gain less than one. (iv) BJT configuration suitable for impedance matching. (v) BIT configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.

Description : Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT ... configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.  

Last Answer : (i) BJT configuration having the least current gain : Common Base Configuration  (ii) KIT configuration called as voltage follower: Common Collector Configuration  (iii) BJT ... Emitter Configuration  (vi) BJT configuration having the least output impedance: Common Collector Configuration

A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current

Description : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

Last Answer : A zener voltage regulator has load requirements of 12 V and 2 A. The zener diode minimum current requirement is 0.2 A. The minimum voltage at input is 24 V. What is the required value of series resistance with source? A) 5.45 Ω B) 6 Ω C) 7.2 Ω D) 6.38 Ω  

The current through a flashlight bulb is 40 mA and the total battery voltage is 4.5 V. The

Description : The current through a flashlight bulb is 40 mA and the total battery voltage is 4.5 V. The resistance of the bulb is approximately? A.112 ohms B.11.2 ohms C.1.2 ohms D.18 ohms

Last Answer : 112ohm

In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two...

Description : In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two wattmeter method, one of the wattmeters reads 20 kW and the other one reads zero. What is the power factor of the load ?

Last Answer : In a balanced 3 -phase 200 V circuit, the line current is 115.5 A. When the power is measured by two wattmeter method, one of the wattmeters reads 20 kW and the other one reads zero. What is the power factor of the load ?  0.5

if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

Description : if voltage is 230 Volts , frequency is 50 Hz and current is 1 ampere then what will be the resistance?

Last Answer : As V = 230v and I = 1A Therfore by ohm's law V =IR R = V/I =230/1 =230 ohm

Compare pin type and suspension insulators on given points: (i) Position of insulator on cross arm. (ii) Position of conductor on insulator. (iii) Reaction on cross arm. (iv) Possibility of flash over due to large birds (v) Maintenance/Replacement cost (vi) Maximum voltage level (vii) Effect on height of supporting structure. (viii) Life

Description : Compare pin type and suspension insulators on given points: (i) Position of insulator on cross arm. (ii) Position of conductor on insulator. (iii) Reaction on cross arm. (iv) Possibility of ... Replacement cost (vi) Maximum voltage level (vii) Effect on height of supporting structure. (viii) Life 

Last Answer : S.No  Points Pin Type insulator Suspension or Disc Type insulator 1 Position of insulator on cross arm It is fixed on top of cross arm by using galvanized steel pin. So it is ... so to maintain minimum ground clearance height of pole increase.  8 Life Less More

A d.c. voltage of 230 V is imposed on an unloaded 230 V, 50 Hz transformer, it will

Description : A d.c. voltage of 230 V is imposed on an unloaded 230 V, 50 Hz transformer, it will (A) give high secondary voltage (B) burn out (C) give secondary voltage as per k (D) None of these

Last Answer : A d.c. voltage of 230 V is imposed on an unloaded 230 V, 50 Hz transformer, it will burn out

In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied

Description : In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is (A) 70 V (B) 50 V (C) 60 V (D) 100 V

Last Answer : In an AC circuit, the voltage across R, L and C are 30 V, 60 V and 20 V respectively. The applied voltage is 50 V

What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively?

Description : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

Last Answer : What is the RMS voltage in a series RL circuit, if the voltage across R and L is 256 V and 192 V respectively? A) 320 V B) 448 V C) 64 V D) None of these

At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is ...

Description : At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is (A) + 120 V (B) – 120 V (C) – 60 V (D) + 60 V

Last Answer : At a particular instant, the R-phase voltage of a balanced 3-phase system is + 30 V, and the Y-phase voltage is – 90 V. The voltage of B-phase at that instant is + 60 V

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of...

Description : When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly  (a) 4.2 V (b) 3.2 V (c) 1.2 V (d) 0.42 V

Last Answer : When 7/0.029 V.I.R cable is carrying 20 A, a drop of 1 V occurs every 12 m. The voltage drop in a 100 m run of this cable when it is carrying 10 A is nearly 1.2 V

A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured...

Description : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: A. 0 V B. 1.2V C. 6V D. 0.6V

Last Answer : A string of five resistors connected in series is connected across a 6 V battery. Zero voltage is measured across all the resistors except the third resistor. The voltage across the third resistor is: 6V

To measure insulation resistance of equipments of voltage rating upto 440 V the megger generator must generate...

Description : To measure insulation resistance of equipments of voltage rating upto 440 V the megger generator must generate   (a) 220 V (b) 440 V (c) 500 V (d) None of these 

Last Answer : 500 V

Electrons accelerated by a p.d. of `V=5000` volts are allowed to impinge normally on a plate. If the current constituted by the impinging electrons be

Description : Electrons accelerated by a p.d. of `V=5000` volts are allowed to impinge normally on a plate. If the current constituted by the impinging electrons be

Last Answer : Electrons accelerated by a p.d. of `V=5000` volts are allowed to impinge normally on a plate. If the current ... -31) kg` and `e=1.6xx10^(-19) C`

The potential difference across a cell is 1.8 V when a current of 0.5 A is drawn from it. The p.d. falls to 1.6 V when a current of 1.0 A is drawn. Fi

Description : The potential difference across a cell is 1.8 V when a current of 0.5 A is drawn from it. The p.d. falls to 1.6 V when a current of 1.0 A is drawn. Fi

Last Answer : The potential difference across a cell is 1.8 V when a current of 0.5 A is drawn from it. ... . Find the emf and the internal resistance of the cell.

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

Describe with neat circuit diagram the method of measurement of power in a High voltage, high current a.c circuit.

Description : Describe with neat circuit diagram the method of measurement of power in a High voltage, high current a.c circuit.

Last Answer : Circuit diagram:  Explanation:  The primary winding of P.T is connected across high voltage side and secondary winding is connected to pressure coil of low range wattmeter. The high voltage is ... is used Real power consumed = reading of wattmeter x ratio of C.T x ratio of P.T

An alternator is delivering rated current at rated voltage and 0.8 power-factor lagging. For delivering rated...

Description : An alternator is delivering rated current at rated voltage and 0.8 power-factor lagging. For delivering rated current at rated voltage and 0.8 poWer—factor leading, the required excitation will be:  (A) less  (B) more (C) more or less (D) the same

Last Answer : An alternator is delivering rated current at rated voltage and 0.8 power -factor lagging. For delivering rated current at rated voltage and 0.8 power -factor leading, the required excitation will be: more 

The product of apparent power and cosine of the phase angle between circuit voltage and current is?

Description : The product of apparent power and cosine of the phase angle between circuit voltage and current is?

Last Answer : In parllpar reasonans RLC circuit the current is

The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

Description : The power consumed in a circuit element will be least when the phase difference between the current and voltage is?

Last Answer : The power consumed in a circuit element will be least when the phase difference between the current and voltage is 90°.

Two stage reciprocating air compressor with P – V diagram

Description : Two stage reciprocating air compressor with P – V diagram

Last Answer : Two stage reciprocating air compressors consist of two cylinders. One is called low-pressure cylinder and another is called high-pressure cylinder. When piston in a low-pressure cylinder is at ... & discharge valves open. This desired high-pressure air is then delivered to a receiver. 

The following is correct : (A) P = V x I (B) P = I ² x R (C) P = V ² / R (D) All of the above

Description : The following is correct : (A) P = V x I (B) P = I ² x R (C) P = V ² / R (D) All of the above

Last Answer : The following is correct : (A) P = V x I (B) P = I ² x R (C) P = V ² / R (D) All of the above

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... B. 160 W C. `37.5 W` D. 60 W