. What type of counter has clock pulses applied to all FFs?

. What type of counter has clock pulses applied to all FFs?
by

1 Answer

Answer :

Synchronous.
by

Related questions

How many clock pulses are required to output a 4-bit number in serial form?

Description : How many clock pulses are required to output a 4-bit number in serial form?

Last Answer : Four.

How many FFs would be required for an 8-bit shift register?

Description : How many FFs would be required for an 8-bit shift register?

Last Answer : Eight.

. How many FFs are required to count down from 1510?

Description : . How many FFs are required to count down from 1510?

Last Answer : Four.

If the specified state is OFF, how many FFs may be off at one time?

Description : If the specified state is OFF, how many FFs may be off at one time?

Last Answer : One.

J-K FFs used in counters are wired to perform what function?

Description : J-K FFs used in counters are wired to perform what function?

Last Answer : Toggle.

What is the purpose of using T FFs?

Description : What is the purpose of using T FFs?

Last Answer : To divide the input by 2.

How may R-S FFs be constructed?

Description : How may R-S FFs be constructed?

Last Answer : By cross-coupling NAND or OR gates.

. How many R-S FFs are required to store the number 1001012?

Description : . How many R-S FFs are required to store the number 1001012?

Last Answer : Six.

What are R-S FFs used for?

Description : What are R-S FFs used for?

Last Answer : Storing information.

A 12 bit counter type A/D converter uses a 1 MHz clock. If the full scale output is +10V, its resolution output is

Last Answer : A 12 bit counter type A/D converter uses a 1 MHz clock. If the full scale output is +10V, its resolution output is 2.44mV.

A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is

Last Answer : A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is 4096μs.

In a bistable multivibrator, how many trigger pulses are needed to produce one complete cycle in the output?

Description : In a bistable multivibrator, how many trigger pulses are needed to produce one complete cycle in the output?

Last Answer : Two.

Which receiver component converts the IF pulses to video pulses?

Description : Which receiver component converts the IF pulses to video pulses?

Last Answer : Detector.

Which of the basic timing circuits produces sharp trigger pulses directly?

Description : Which of the basic timing circuits produces sharp trigger pulses directly?

Last Answer : Blocking oscillators.

Which of the basic timing circuits produces sharp trigger pulses directly?

Description : Which of the basic timing circuits produces sharp trigger pulses directly?

Last Answer : Blocking oscillators.

what causes the initial and final pulses on the receiver output signal?

Description : what causes the initial and final pulses on the receiver output signal?

Last Answer : Leakage from the duplexer.

A self-synchronized radar system obtains timing trigger pulses from what source?

Description : A self-synchronized radar system obtains timing trigger pulses from what source?

Last Answer : Transmitter.

Range-marker generators produce pulses based on what radar constant?

Description : Range-marker generators produce pulses based on what radar constant?

Last Answer : The radar mile (12.36 microseconds).

Current that flows in pulses in the same direction is called

Description : Current that flows in pulses in the same direction is called

Last Answer : Pulsating dc

What method for encoding digital data enables you to store more data in less space by limiting the distance between pulses on a hard disk?

Description : What method for encoding digital data enables you to store more data in less space by limiting the distance between pulses on a hard disk?

Last Answer : Run length-limited (RLL) encoding.

Which method of digital data encoding does NOT return the tape to neutral between pulses but, instead, saturates the tape positively or negatively as the incoming data changes between zero and one?

Description : Which method of digital data encoding does NOT return the tape to neutral between pulses but, instead, saturates the tape positively or negatively as the incoming data changes between zero and one?

Last Answer : Non-return-to-zero (NRZ) encoding.

Which digital data encoding method records a digital one as a positive pulse and a digital (zero) as a negative pulse and returns the tape to neutral between pulses?

Description : Which digital data encoding method records a digital one as a positive pulse and a digital (zero) as a negative pulse and returns the tape to neutral between pulses?

Last Answer : Return-to-zero (RZ) encoding.

What format of digital tape recording takes a serial input stream of data pulses, breaks them up, and records them on more than one data track?

Description : What format of digital tape recording takes a serial input stream of data pulses, breaks them up, and records them on more than one data track?

Last Answer : Serial-parallel digital magnetic tape recording.

In digital magnetic tape recording, the series of recorded digital pulses can represent what three types of data?

Description : In digital magnetic tape recording, the series of recorded digital pulses can represent what three types of data?

Last Answer : a. Data used by digital computers. b. Pulsed squarewave signals. c. Digitized analog waveforms.

Solution of fertilizer specially applied at initial growth of plants in pulses and vegetable crops

Description : Solution of fertilizer specially applied at initial growth of plants in pulses and vegetable crops

Last Answer : Ans. Starter solution

Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency

Description : Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency is (a) 2.65 MHz (b) 6.25 MHz (c) 5.26 MHz (d) 6.52 MHz 

Last Answer : Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 ns. The maximum clock frequency is 6.25MHz. nff  * Tdelay = 4*40 =160ns so, max. frequency = 1/ (200*10-9 ) = 6.25MHz          

Suppose that the same clock signal is used to increment the microprogram counter and to load the control

Description : Suppose that the same clock signal is used to increment the microprogram counter and to load the control register. Which of the following assertion(s) is/are true?  1. Microinstruction execution time is at least two clock periods.  ... other types.  (a) 1 only (b) 2 only (c) 1 and 3 (d) 2 and 3

Last Answer : Suppose that the same clock signal is used to increment the microprogram counter and to load the control register. Which of the following assertion(s) is/are true?  1. Microinstruction execution time is at least two clock periods.  ... types.  (a) 1 only (b) 2 only (c) 1 and 3 (d) 2 and 3

What type of clock is used when more than one operation is to be completed during one clock cycle?

Description : What type of clock is used when more than one operation is to be completed during one clock cycle?

Last Answer : . A multiphase clock.

What is the simplest type of clock circuit?

Description : What is the simplest type of clock circuit?

Last Answer : An astable or free-running multivibrator.

A, what logic element enables FF3 to toggle with the clock?

Description : A, what logic element enables FF3 to toggle with the clock?

Last Answer : The AND gate

What is needed to use a monostable or one-shot multivibrator for a clock circuit?

Description : What is needed to use a monostable or one-shot multivibrator for a clock circuit?

Last Answer : Triggers.

What is a clock with regard to digital equipment?

Description : What is a clock with regard to digital equipment?

Last Answer : A timing signal.

What logic levels must exist for the FF to be toggled by the clock?

Description : What logic levels must exist for the FF to be toggled by the clock?

Last Answer : Both J and K must be HIGH.

What will be the output of Q if J is HIGH, PS and CLR are HIGH, and the clock is going negative?

Description : What will be the output of Q if J is HIGH, PS and CLR are HIGH, and the clock is going negative?

Last Answer : Set, or HIGH (1).

What is the difference between a positive counter and a step counter?

Description : What is the difference between a positive counter and a step counter?

Last Answer : The load resistor in a positive counter is replaced by a capacitor in a step counter.

How do uhf tubes counter the effects of transit time?

Description : How do uhf tubes counter the effects of transit time?

Last Answer : By reducing the spacing between tube elements.

What is the largest count that can be indicated by a four stage counter?

Description : What is the largest count that can be indicated by a four stage counter?

Last Answer : 11112, or 1510.

An asynchronous counter is also called a ___________ counter.

Description : An asynchronous counter is also called a ___________ counter.

Last Answer : Ripple

What is the modulus of a five-stage binary counter?

Description : What is the modulus of a five-stage binary counter?

Last Answer : 32.

What is meant by induced emf? By counter emf?

Description : What is meant by induced emf? By counter emf?

Last Answer : Induced emf is the emf which appears across a conductor when there is relative motion between the conductor and a magnetic field; counter emf is the emf induced in a conductor that opposes the applied voltage.

What motor characteristic is affected by counter emf?

Description : What motor characteristic is affected by counter emf?

Last Answer : Speed.

What causes counter emf in a dc motor

Description : What causes counter emf in a dc motor

Last Answer : Generator action.

The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ.

Description : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is A) 10 KHz B) 2.5 KHz C) 20 KHz D) 5 KHz

Last Answer : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is 5 KHz

Correction is applied to LMTD for __________ flow. (A) Parallel (B) Counter (C) Cross (D) None of these

Description : Correction is applied to LMTD for __________ flow. (A) Parallel (B) Counter (C) Cross (D) None of these

Last Answer : (C) Cross

Article addressed to deceased person a) Delivery such articles to any near relative of the deceased who may have applied for them in case uninsured article. b) Delivery such articles to any near relative of the deceased who may have applied for them in case do not appear to contain any valuable property c) Delivery such articles to any near relative of the deceased who may have applied for them in case no counter –claimant or likelihood of dispute. d) All the above

Description : Article addressed to deceased person a) Delivery such articles to any near relative of the deceased who may have applied for them in case uninsured article. b) Delivery such articles to any near relative ... applied for them in case no counter -claimant or likelihood of dispute. d) All the above

Last Answer : d) All the above

If a switch must be checked with power applied, what type of meter is used?

Description : If a switch must be checked with power applied, what type of meter is used?

Last Answer : A voltmeter.

What is the relationship between the polarity of the voltage applied to the PNP transistor and that applied to the NPN transistor?

Description : What is the relationship between the polarity of the voltage applied to the PNP transistor and that applied to the NPN transistor?

Last Answer : The polarity of voltage applied to the PNP transistor is opposite of that applied to the NPN

To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Description : To properly bias an NPN transistor, what polarity voltage is applied to the collector, and what is its relationship to the base voltage?

Last Answer : Positive, more positive.

What three things prevent a CT rotor from turning when voltages are applied to its stator windings?

Description : What three things prevent a CT rotor from turning when voltages are applied to its stator windings?

Last Answer : The rotor is specially wound, it is never connected to an ac supply, and its output is always applied to a high-impedance load.

In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Description : In applications where electronic waveforms are displayed on a CRT screen, the input signal is normally applied to what CRT element?

Last Answer : The vertical-deflection plate.