A 12 bit counter type A/D converter uses a 1 MHz clock. If the full scale output is +10V, its resolution output is

by

1 Answer

Answer :

A 12 bit counter type A/D converter uses a 1 MHz clock. If the full scale output is +10V, its resolution output is 2.44mV.

by

Related questions

A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is

Last Answer : A 12 bit counter type A/D converter uses a 1 MHz clock. Its maximum conversion time is 4096μs.

The conversion time of a 12 bit successive approximation A/D converter using a 1 MHz clock is

Last Answer : The conversion time of a 12 bit successive approximation A/D converter using a 1 MHz clock is 12μs.

The resolution of a 12 bit D/A converter using a binary ladder is

Last Answer : The resolution of a 12 bit D/A converter using a binary ladder is 0.02%.

In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of

Description : In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of bits required is   (A) 7 (B) 8 (C) 9 (D) 200

Last Answer : In D/A converter, the resolution required is 50mv and the total maximum input is 10v. The number of  bits required is 8 

An 8 bit converter type A/D converter makes at least 8000conversions/sec. The clock frequency used is

Last Answer : An 8 bit converter type A/D converter makes at least 8000conversions/sec. The clock frequency used is 2MHz.

An eight bit digital data 10101100 is fed to an ADC. The reference voltage is +10V. The analog output voltage ...

Description : An eight bit digital data 10101100 is fed to an ADC. The reference voltage is +10V. The analog output voltage will be:  (1) 1.05V (2) 6.74V (3) 10.10V (4) 5.15V

Last Answer : An eight bit digital data 10101100 is fed to an ADC. The reference voltage is +10V. The analog output voltage will be: 6.74V.

Consider a 32 - bit microprocessor, with a 16 - bit external data bus, driven by an 8 MHz input clock. Assume that the microprocessor has a bus cycle whose minimum duration equals four input clock cycles. What is the maximum data transfer rate for this microprocessor? (A) 8x106 bytes/sec (B) 4x106 bytes/sec (C) 16x106 bytes/sec (D) 4x109 bytes/sec

Description : Consider a 32 - bit microprocessor, with a 16 - bit external data bus, driven by an 8 MHz input clock. Assume that the microprocessor has a bus cycle whose minimum duration equals four input clock cycles. What ... (A) 8x106 bytes/sec (B) 4x106 bytes/sec (C) 16x106 bytes/sec (D) 4x109 bytes/sec 

Last Answer : (B) 4x106 bytes/sec

An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.

The percent resolution of an 8 -bit D/A converter is

Description : The percent resolution of an 8 -bit D/A converter is

Last Answer : The percent resolution of an 8 -bit D/A converter is 0.392

For a certain 4 bit successive approximation A/D converter, the maximum ...

Last Answer : For a certain 4 bit successive approximation A/D converter, the maximum ladder output is +8V. if a constant +6V is applied to the analog input the sequence of binary states for the SA register is 0110.

Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency

Description : Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 n sec. The maximum clock frequency is (a) 2.65 MHz (b) 6.25 MHz (c) 5.26 MHz (d) 6.52 MHz 

Last Answer : Each flip-flop in a 4-bit ripple counter introduces a maximum delay of 40 ns. The maximum clock frequency is 6.25MHz. nff  * Tdelay = 4*40 =160ns so, max. frequency = 1/ (200*10-9 ) = 6.25MHz          

An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V.

Description : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is  A) 25 micro-volt B) 50 micro-volt C) 5 Volts D) 10 volts

Last Answer : An operational amplifier has an open loop gain of 200,000. Its output exhibits saturation at 10V. The threshold differential voltage of the amplifier is 50 micro-volt

A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the...

Description : A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010:  (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V

Last Answer : 3.125V

What is the common up-converter and down-converter IF? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Description : What is the common up-converter and down-converter IF? A. 36 MHz B. 40 MHz C. 70 MHz D. 500 MHz

Last Answer : C. 70 MHz

What is the common up-converter and down-converter IF for microwave communications? A. 60 MHz B. 80 MHz C. 120 MHz D. 70 MHz

Description : What is the common up-converter and down-converter IF for microwave communications? A. 60 MHz B. 80 MHz C. 120 MHz D. 70 MHz

Last Answer : D. 70 MHz

How many clock pulses are required to output a 4-bit number in serial form?

Description : How many clock pulses are required to output a 4-bit number in serial form?

Last Answer : Four.

A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Description : A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Last Answer : Ans: A 15 ns because in synchronous counter all the flip-flops change state at the same time.

The maximum clock frequency is _ a. 45 MHZ b. 50 MHZ c. 52 MHZ d. 68 MHZ

Description : The maximum clock frequency is _ a. 45 MHZ b. 50 MHZ c. 52 MHZ d. 68 MHZ

Last Answer : b. 50 MHZ

In 8085 microprocessor, the digit 5 indicates that the microprocessor needs (1) -5 volts, +5 volts supply (2) +5 volts supply only (3) -5 volts supply only (4) 5 MHz clock

Description : In 8085 microprocessor, the digit 5 indicates that the microprocessor needs (1) -5 volts, +5 volts supply (2) +5 volts supply only (3) -5 volts supply only (4) 5 MHz clock

Last Answer : Answer: 2

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

The A/D converter whose conversion time is independent of the number of bits is (A) Dual slope (B) Counter type (C) Parallel conversion (D) Successive approximation.

Description : The A/D converter whose conversion time is independent of the number of bits is (A) Dual slope (B) Counter type (C) Parallel conversion (D) Successive approximation.

Last Answer : Ans: C The A/D converter whose conversion time is independent of the Number of bits is Parallel conversion. (This type uses an array of comparators connected in parallel and comparators compare the input voltage at a particular ratio of the reference voltage).

Julie is going on an extended trip for three weeks. She lives in a remote area where there are frequent electrical power outages which can last up to three or four days. Julie has quite a bit of food in her freezer which would go bad if it thawed and then re-froze. She does have digital clock and a VCR which would flash 12:00 if the power went out. Unfortunately the clock and VCR flash even if the power only goes out for a few seconds. What can Julie do so that when she returns home she will be able to determine whether the power was out long enough to thaw her food? Asking a neighbor whether the power was out, isn't a reliable option because the nearest house is half a mile away, and one house may have power, while another house may have no power. She won?t be able to have a neighbor chec

Description : Julie is going on an extended trip for three weeks. She lives in a remote area where there are frequent electrical power outages which can last up to three or four days. Julie has quite a bit of food ... power, while another house may have no power. She won?t be able to have a neighbor chec -Riddles

Last Answer : One thing Julie could do is freeze a tray of ice-cubes, and turn the tray of ice upside down in her freezer. When she comes home, she should check the tray. If the ice cubes are still in the ... clean out the freezer. She will have to make a judgment call if the ice-cubes are only slightly thawed.

Define resolution of a data converter.

Description : Define resolution of a data converter.

Last Answer : The resolution of a converter is the smallest change in voltage which may be produced at the output or input of the converter. Resolution (in volts)= VFS/2n-1=1 LSB increment. The resolution of an ADC is defined as the smallest change in analog input for a one bit change at the output.

. What type of counter has clock pulses applied to all FFs?

Description : . What type of counter has clock pulses applied to all FFs?

Last Answer : Synchronous.

The speed of conversion is maximum in (A) Successive-approximation A/D converter. (B) Parallel-comparative A/D converter. (C) Counter ramp A/D converter. (D) Dual-slope A/D converter.

Description : The speed of conversion is maximum in (A) Successive-approximation A/D converter. (B) Parallel-comparative A/D converter. (C) Counter ramp A/D converter. (D) Dual-slope A/D converter.

Last Answer : Ans: B The speed of conversion is maximum in Parallel-comparator A/D converter (Speed of conversion is maximum because the comparisons of the input voltage are carried out simultaneously.)

A bit-stuffing based framing protocol uses an 8-bit delimiter pattern of 01111110. If the output bit-string after stuffing is 01111100101, then the input bit-string is a. 0111110100 b. 0111110101 c. 0111111101 d. 0111111111

Description : A bit-stuffing based framing protocol uses an 8-bit delimiter pattern of 01111110. If the output bit-string after stuffing is 01111100101, then the input bit-string is a. 0111110100 b. 0111110101 c. 0111111101 d. 0111111111

Last Answer : b. 0111110101

The number of comparators required in a 3-bit comparator type analog to digital converter is

Description : The number of comparators required in a 3-bit comparator type analog to digital converter is  A) 2 B) 3 C) 7 D) 8 

Last Answer : Number of comparators =2^n -1= 2^3 -1=7

If the clock frequency to the circuit shown in the illustration were 100 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 10.1 kHz B. 12.5 kHz C. 805 kHz D. 1010 kHz

Description : If the clock frequency to the circuit shown in the illustration were 100 kHz, what would be indicated at the output of 'FF-C'? EL-0087 A. 10.1 kHz B. 12.5 kHz C. 805 kHz D. 1010 kHz

Last Answer : Answer: B

The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. ...

Description : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. What is the value of series resistor to be used?

Last Answer : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. 99.99 K ohms is the value of series resistor to be used.

The full-scale deflection current of an ammeter is 1 mA and its internal...

Description :  The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, what is the value of the shunt resistance to be used?

Last Answer :  The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. If this meter is to have full deflection at 5A, 1/49.99 ohms is the value of the shunt resistance to be used.

Which of the following systems uses frequency band 870-885 MHz as a transmit band of its base station? A. TACS B. NTT C. NMT D. AMPS

Description : Which of the following systems uses frequency band 870-885 MHz as a transmit band of its base station? A. TACS B. NTT C. NMT D. AMPS

Last Answer : B. NTT

Suppose that the same clock signal is used to increment the microprogram counter and to load the control

Description : Suppose that the same clock signal is used to increment the microprogram counter and to load the control register. Which of the following assertion(s) is/are true?  1. Microinstruction execution time is at least two clock periods.  ... other types.  (a) 1 only (b) 2 only (c) 1 and 3 (d) 2 and 3

Last Answer : Suppose that the same clock signal is used to increment the microprogram counter and to load the control register. Which of the following assertion(s) is/are true?  1. Microinstruction execution time is at least two clock periods.  ... types.  (a) 1 only (b) 2 only (c) 1 and 3 (d) 2 and 3

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the

Description : a single phase full wave midpoint thyristor converter uses a 230/200V transformer with centre tap on the secondary side. The P.I.V per thyristor is   (A) 100V (B)141.4V (C)200V (D)282.8V

Last Answer : d

A 0-10 A ammeter has a guaranteed accuracy of 1% of full scale deflection, the limiting error while reading

Description : A 0-10 A ammeter has a guaranteed accuracy of 1% of full scale deflection, the limiting error while reading 2.5 A will be (a) 1% (b) 2% (c) 4% (d) None of these 

Last Answer : A

A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the

Description : A digital voltmeter has a read-out range from 0 to 9999 counts. When full scale reading is 9.999 V, the resolution of the instrument will be (a) 100 mV (b) 99 mV (c) 9 mV (d) 1 mV 

Last Answer : d) 1mV 9.999v÷9999v

A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD)

Description : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

Last Answer : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is: 0.05mA

A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying

Description : A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect • 10 W resistance in series • 10 W resistance in parallel • 10/1999 W resistance in series • 10/1999 W resistance in parallel

Last Answer : A moving coil instrument has a resistance of 10 W and gives full scale deflection when carrying a current of 50 mA. To measure current upto 100 A, we will have to connect 10/1999 W resistance in parallel

A 0 to 300V voltmeter has a guaranteed accuracy of 1% of full scale...

Description : A 0 to 300V voltmeter has a guaranteed accuracy of 1% of full scale reading. The voltage measured by the instrument is 83V. The percentage limiting error is

Last Answer : A 0 to 300V voltmeter has a guaranteed accuracy of 1% of full scale reading. The voltage measured by the instrument is 83V. The percentage limiting error is 4.85%.

If two meters X and Y requires 40mA and 50mA respectively, to give full scale deflection, then:

Last Answer : If two meters X and Y requires 40mA and 50mA respectively, to give full scale deflection, then: X is more sensitive

The ratio of maximum displacement deviation to full scale deviation of the instrument is called?

Description : The ratio of maximum displacement deviation to full scale deviation of the instrument is called?

Last Answer : The ratio of maximum displacement deviation to full scale deviation of the instrument is called linearity.

The 2G GSM technology uses a carrier separation of _____________ a) 1.25 MHz b) 200 KHz c) 30 KHz d) 300 KHz

Description : The 2G GSM technology uses a carrier separation of _____________ a) 1.25 MHz b) 200 KHz c) 30 KHz d) 300 KHz

Last Answer : b) 200 KHz

In the network shown in fig. , points A, B, and C are at potentials of 70 V, 0, and 10V, respectively.

Description : In the network shown in fig. , points A, B, and C are at potentials of 70 V, 0, and 10V, respectively.

Last Answer : In the network shown in fig. , points A, B, and C are at potentials of 70 V, 0, and 10V, respectively. ... AB, DB and DC are in the ratio of `3:2:1`

Two cells of emfs approximately 5V and 10V are to be accurately compared using a poteniometer of length 400 cm.

Description : Two cells of emfs approximately 5V and 10V are to be accurately compared using a poteniometer of length 400 cm.

Last Answer : Two cells of emfs approximately 5V and 10V are to be accurately compared using a ... usually used for comparing resistances and not voltages

In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. Switch S is closed at time t=D. Suppose at som

Description : In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. Switch S is closed at time t=D. Suppose at som

Last Answer : In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. ... will A. 10 J B. 15 J C. 25 J D. 40 J

In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Description : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choose t

Last Answer : In an L-C -R search circuit connected to an AC source `V=V_(0)sin(100pi+(pi)/(6))``V_(R)=40V, V_ ... (a) and (b) are correct D. Both a and b are wrong

In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Description : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L)=40 and V_(C )=10V`, resistance `R=4Omega` Choos

Last Answer : In an L-C -R series circuit connected to an AC source `V=V_(0)sin(100pi(t)+(pi)/(6))``V_(R)=40V, V_(L) ... (2) A` C. `20sqrt(2) A` D. `25sqrt(2) A`

In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. Switch S is closed at time t=D. Suppose at som

Description : In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. Switch S is closed at time t=D. Suppose at som

Last Answer : In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. ... (2) A` C. `20sqrt(3) A` D. `12sqrt(6) A`

In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. Switch S is closed at time t=D. Suppose at som

Description : In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. Switch S is closed at time t=D. Suppose at som

Last Answer : In the figure shown `C_(1)=1F, C_(2)=2F and L=5H`. Initially `C_(1)` is charged 50V and `C_(2)` to 10V. ... ` B. `15sqrt(2) A` C. `10 A` D. `20 A`

Why 4-20 Ma Signal Is Preferred Over A 0-10v Signal?

Description : Why 4-20 Ma Signal Is Preferred Over A 0-10v Signal?

Last Answer : Generally in a transistor some amount of voltage is required for turning it on. This voltage is the cut in voltage. Up to this voltage the exists a nonlinearity in its characteristics. Beyond this cut in voltage ... region lays between 0-4ma, beyond 4ma it linear. This is why 4-20 ma range is used.