Why does the voltage not drop when you plug in a power strip?

Why does the voltage not drop when you plug in a power strip?
by

1 Answer

Answer :

The sockets are in parallel.
by

Related questions

If I have a 110v outlet and plug in a power strip with five sockets, why do I get 110v out of each instead of 22v?

Description : If I have a 110v outlet and plug in a power strip with five sockets, why do I get 110v out of each instead of 22v?

Last Answer : answer:Because of the type of circuit used. This is called a parallel circuit. Compare voltage to water pressure. If you would poke multiple holes at the same height from the bottom of a bucket full ... the pressure at each hole stays the same, independent from other holes you'd poke in the bucket.

What is the most likely thing to happen if I must plug in the very short cord of a small electrical appliance into an extension cord or power strip rather than a wall outlet? What's the worst that could happen?

Description : What is the most likely thing to happen if I must plug in the very short cord of a small electrical appliance into an extension cord or power strip rather than a wall outlet? What's the worst that could happen?

Last Answer : For some reason toasters have notoriously short cords and I've never received a reasonable excuse. The best I could come up with was that the cord was kept short to prevent the thing from falling ... has a 3 prong plug (grounded) you want a grounded extension cord plugged into a grounded outlet.

Just how bad is it to plug a power strip into an extension chord into the wall?

Description : Just how bad is it to plug a power strip into an extension chord into the wall?

Last Answer : Not at all. Your circuit breakers will pop before anything happens, but what you have shouldn’t cause any problems.

Is it unsafe to plug a power strip into an extension cord permanently?

Description : Is it unsafe to plug a power strip into an extension cord permanently?

Last Answer : Its unsafe. If you need power permanently you need to run to run a new box and receptacle off a pre-existing circuit. You might need to run a whole new circuit and add a new breaker in your electrical panel if what your using requires more juice than a pre-existing circuit can safely handle.

Why does my computer output volume drop to 20% whenever I plug/unplug a USB device?

Description : Why does my computer output volume drop to 20% whenever I plug/unplug a USB device?

Last Answer : answer:I don’t know. I just wanted to say hi. Hi!

A Hybrid Vehicle equipped with push button start will enter the power ON mode but will not enter the ready to drive mode .No diagnostic trouble code are stored this could cause by a) The high voltage safety plug is removed b) A failed brake on/off switch c) An empty fuel tank d) A disconnect 12v battery

Description : A Hybrid Vehicle equipped with push button start will enter the power ON mode but will not enter the ready to drive mode .No diagnostic trouble code are stored this could cause by a) The high voltage safety ... removed b) A failed brake on/off switch c) An empty fuel tank d) A disconnect 12v battery

Last Answer : b) A failed brake on/off switch

In a DC series circuit, all the conductors have the same ____________. A. power expended in them B. voltage drop across them C. resistance to current flow D. current passing through them

Description : In a DC series circuit, all the conductors have the same ____________. A. power expended in them B. voltage drop across them C. resistance to current flow D. current passing through them

Last Answer : Answer: D

The sparking voltage of the spark plug is A. 6 to 12 V B. 100 to 450 V C. 1 to 2 kV D. 20 to 30kV

Description : The sparking voltage of the spark plug is A. 6 to 12 V B. 100 to 450 V C. 1 to 2 kV D. 20 to 30kV

Last Answer : ANSWER : D

Receptacle outlets aboard ship should be designed so those mounted according to 46 CFR 111 have _____________. A. there must be a sufficient number of receptacle outlets in the crew accommodations for an adequate level of habitability B. each receptacle outelt must be compatible with the voltage and current of the circuit in which it is installed C. a receptacle outlet must not have any exposed parts with the plug opening uncovered D. all of the above

Description : Receptacle outlets aboard ship should be designed so those mounted according to 46 CFR 111 have _____________. A. there must be a sufficient number of receptacle outlets in the crew accommodations for an ... outlet must not have any exposed parts with the plug opening uncovered D. all of the above

Last Answer : Answer: D

How to tell if a power strip is burned out?

Description : How to tell if a power strip is burned out?

Last Answer : answer:Personally, I would either toss it, or down grade it to outdoor use only. I wouldn’t take a chance with it in the house. Yes, you can let it cool down, then test it again. But a failure is a failure. Does it have a reset button? What price range did you pay?

Bringing more than one US appliance to UK: multiple adapters, or one adapter and a power strip?

Description : Bringing more than one US appliance to UK: multiple adapters, or one adapter and a power strip?

Last Answer : answer:Multiple adapters sounds safer. Realistically how many devices are you going to need to use simultaneously? It may be that you don’t actually need an adapter for each device you are going to bring.

Can you put more than 1 power strip on an outlet?

Description : Can you put more than 1 power strip on an outlet?

Last Answer : A power strip (also known as an extension block, power board, plug board and by many other variations) is a block of electrical sockets that attaches to the end of a flexible cable ( ... systems. Power strips often include a circuit breaker to safely limit the electric current flowing through them

Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions properly and trips generator #1 electrically off the bo A. Start the emergency generator. B. Ascertain cause of the low lube oil pressure. C. Strip the board of all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Description : Diesel generators #1 and #2 are operating in parallel at near full load capacity. Diesel generator #1 suddenly trips out mechanically due to low lube oil pressure. The reverse power relay functions ... all nonvital circuits. D. Secure alarms, reset reverse power relay, and restart #1 engine.

Last Answer : Answer: C

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

A 24 volt battery supplies three devices wired in parallel that each have a resistance of 9 ohms. What is the voltage drop across each device?

Description : A 24 volt battery supplies three devices wired in parallel that each have a resistance of 9 ohms. What is the voltage drop across each device?

Last Answer : A simple circuit has three resistors connected in series. The resistors are 14 ohms 12 ohms and 9 ohms. What is the total resistance of the circuit?

What is voltage drop ?

Description : What is voltage drop ?

Last Answer : Answer : The loss of electrical current along a conductor when an electric current passes through its conductor in a conductor or equipment is called voltage deficit .

In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro

Description : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the polarity as indicated. The ratio of potential difference acro

Last Answer : In the circuit shown the voltage drop across the `15Omega` resistor is `30 V` having the ... difference across `5Omega` and resistance `R` is

Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, R_(1)=5 k Omega, R_(2)=5k Omega, R_(3)=

Description : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, R_(1)=5 k Omega, R_(2)=5k Omega, R_(3)=

Last Answer : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, ... k Omega " and " R_(4)=10 k Omega`.

How does voltage drop related to impressed emf?

Description : How does voltage drop related to impressed emf?

Last Answer : Voltage drop is resultant of IR ie current and the lineresistance, not dependent on impressed emf

How are the voltage drop across R and XL related in series RL circuit?

Description : How are the voltage drop across R and XL related in series RL circuit?

Last Answer : Voltage drop across a circuit is IZ, where I is current and Z isimpedance. In other words IZ = IR + jIX, where R is resistance andX is inductance

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

What causes a voltage drop on a 12 volt battery?

Description : What causes a voltage drop on a 12 volt battery?

Last Answer : Need answer

What is the Voltage drop of R1 If V 10 Volts R1 500 Ohms and R2 1500 Ohms?

Description : What is the Voltage drop of R1 If V 10 Volts R1 500 Ohms and R2 1500 Ohms?

Last Answer : You need to mention whether the resistors are in series or parallel to get the right answer

As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow through 'R1' will equal the current flow through 'R2' C. the energy dissipated in 'R1' will be the same as the energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Description : As shown in the illustration, if 'R1' and 'R2' have unequal values, the ____________. EL-0019 A. voltage drop across 'R1' will not be equal to the voltage drop across 'R2' B. current flow ... energy dissipated in 'R2' D. current flow through 'R1' will differ from the current flow through 'R2'

Last Answer : Answer: D

Three factors responsible for the change in voltage as load is applied to an AC generator are: 1) the drop in resistance in the armature circuit, 2) the change in flux, and 3) the ____________. A. armature winding speed B. inductance load drop C. coil pitch factor D. armature reactance voltage drop

Description : Three factors responsible for the change in voltage as load is applied to an AC generator are: 1) the drop in resistance in the armature circuit, 2) the change in flux, and 3) the ____________. A. armature winding speed B. inductance load drop C. coil pitch factor D. armature reactance voltage drop

Last Answer : Answer: D

A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across each field coil C. using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Description : A short in the shunt field of a DC motor is best located by _____________. A. visual inspection of the commutator B. applying AC voltage to each field coil and measuring the voltage drop across ... using a growler and hacksaw blade D. isolating each coil from the others and using a megohmmeter

Last Answer : Answer: B

The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Last Answer : Answer: D

In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Description : In the illustrated circuit the voltage is 12 VDC and the resistance is 3 ohms. If the battery is rated for 120 amp-hours, how long before the voltage will drop to 1.75 volts per cell? EL-0018 A. 12 hours B. 1.75 days C. 30 hours D. 2.5 days

Last Answer : Answer: C

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the series resistor of the circuit shown in the illustration if the source is 30 volts, the resistance of R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: C

What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Description : What would be the voltage drop across the parallel branches of the circuit shown in the illustration if the source is 30 volts the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 volts B. 10 volts C. 20 volts D. 30 volts

Last Answer : Answer: B

The instantaneous reduction in voltage of an AC generator, resulting from an increase in load, and prior to the automatic voltage regulator correcting the situation, is called voltage ____________. A. droop B. drop C. dip D. regulation

Description : The instantaneous reduction in voltage of an AC generator, resulting from an increase in load, and prior to the automatic voltage regulator correcting the situation, is called voltage ____________. A. droop B. drop C. dip D. regulation

Last Answer : Answer: C

In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Description : In a simple series circuit, the entire source voltage will drop across ______________. A. the resistor next to the negative terminal B. a short circuit C. the resistor next to the positive terminal D. an open circuit

Last Answer : Answer: D

If a magnetic controller relay fails to drop out when the coil voltage is removed from the relay, the probable cause may be _____________. A. excessive spring tension B. overvoltage C. excessive current D. welded contacts

Description : If a magnetic controller relay fails to drop out when the coil voltage is removed from the relay, the probable cause may be _____________. A. excessive spring tension B. overvoltage C. excessive current D. welded contacts

Last Answer : Answer: D

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of a. Loss per foot b. dB/km c. intensity per mile d. voltage drop per inch

Last Answer : b. dB/km

If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Why pick up voltage is more than drop out voltage?

Description : Why pick up voltage is more than drop out voltage? 

Last Answer : Initially air gap is more. Large force is required to overcome the high reluctance initially. After closing air gap is reduced. Hence drop voltage is reduced.  

In order that current should flow without causing excessive heating or voltage drop, the relay contacts should (a) have low contact resistance (b) be clean and smooth (c) be of sufficient size and proper shape (d) have all above properties

Description : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should (a) have low contact resistance (b) be clean and smooth (c) be of sufficient size and proper shape (d) have all above properties

Last Answer : (d) have all above properties

the voltage drop across RS and R1 determines the amount of base-emitter ____ for Q1.

Description : the voltage drop across RS and R1 determines the amount of base-emitter ____ for Q1.

Last Answer : Bias.

how is (a) the current through R2 and (b) the voltage drop across R2 computed?

Description : how is (a) the current through R2 and (b) the voltage drop across R2 computed?

Last Answer : (a) By adding the bleeder current (IR1) and the current through load 1(b) By subtracting the voltage of load 1 from the voltage of load 2.

If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Description : If the current was increased to 4 amps, what would be the voltage drop across each resistor in the circuit described in question 17?

Last Answer : E1 = 80 volts. E2 = 240 volts. E3 = 320 volts

What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Description : What is the voltage drop across the resistor in an RC charging circuit when the charge on the capacitor is equal to the battery voltage?

Last Answer : Zero.

Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Last Answer : . dB/km

Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Last Answer : ∙ b. dB/km

The voltage drop, for constant voltage transmission is compensated by installing (a) inductors (b) capacitors (c) synchronous motors (d) all of above (e) none of the above

Description : The voltage drop, for constant voltage transmission is compensated by installing (a) inductors (b) capacitors (c) synchronous motors (d) all of above (e) none of the above

Last Answer : (c) synchronous motors

A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Description : A resistor of value R/2 is connected in parallel with a resistor of value R/3. The voltage drop across the parallel combination is V. The total current supplied by the voltage source is: w) 2 V/R (read: 2 V over R) x) 3 V/R (read: 3 V over R) y) 4 V/R (read: 4 V over R) z) 5 V/R (read: 5 V over R)

Last Answer : ANSWER: Z -- 5 V/R

An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Description : An LED is operated on a 12 volt automobile circuit. The voltage drop across the LED is 2 volts and the current must be limited to 50 milliamps to prevent its overheating and destruction. What size resistor must be used? w) 60 ohms x) 100 ohms y) 120 ohms z) 200 ohms

Last Answer : ANSWER: Z -- 200 OHMS