Regarding plane-table survey, which of the following statements does not hold? (a) All the plotting work including contouring can be done in the field (b) It is quite suitable for small scale survey (c) Less number of control points are required (d) It can be done in all seasons

Regarding plane-table survey, which of the following statements does not hold?
(a) All the plotting work including contouring can be done in the field
(b) It is quite suitable for small scale survey
(c) Less number of control points are required
(d) It can be done in all seasons
by

1 Answer

Answer :

(d) It can be done in all seasons
by

Related questions

The plotting of inaccessible points in a plane-table survey can be done by the method of (a) Interpolation (b) Radiation (c) Intersection (d) Traversing

Description : The plotting of inaccessible points in a plane-table survey can be done by the method of (a) Interpolation (b) Radiation (c) Intersection (d) Traversing

Last Answer : (c) Intersection

The method generally preferred to for contouring an undulating area, is (A) Chain surveying (B) Plane table surveying (C) Tacheometrical surveying (D) Compass surveying

Description : The method generally preferred to for contouring an undulating area, is (A) Chain surveying (B) Plane table surveying (C) Tacheometrical surveying (D) Compass surveying

Last Answer : (C) Tacheometrical surveying

While surveying a plot of land by plane tabling, the field observations (A) And plotting proceed simultaneously (B) And plotting do not proceed simultaneously (C) And recorded in field books to be plotted later (D) All the above

Description : While surveying a plot of land by plane tabling, the field observations (A) And plotting proceed simultaneously (B) And plotting do not proceed simultaneously (C) And recorded in field books to be plotted later (D) All the above

Last Answer : (A) And plotting proceed simultaneously

In a plane-table survey, the process of determining the plotted position of a station occupied by the plane-table by means of sights taken towards known points, the locations of which have already been plotted, is known as (a) Radiation (b) Resection (c) Intersection (d) Traversing

Description : In a plane-table survey, the process of determining the plotted position of a station occupied by the plane-table by means of sights taken towards known points, the locations of which have already been plotted, is known as (a) Radiation (b) Resection (c) Intersection (d) Traversing

Last Answer : (b) Resection

In direct method of contouring, the process of locating or identifying points lying on a contour is called (A) Ranging (B) Centring (C) Horizontal control (D) Vertical control

Description : In direct method of contouring, the process of locating or identifying points lying on a contour is called (A) Ranging (B) Centring (C) Horizontal control (D) Vertical control

Last Answer : (D) Vertical control

For preparation of a contour plan for a route survey (A) Method of squares is used (B) Method of trace contour is used (C) Method of cross profile is used (D) Indirect method of contouring is used

Description : For preparation of a contour plan for a route survey  (A) Method of squares is used  (B) Method of trace contour is used  (C) Method of cross profile is used  (D) Indirect method of contouring is used 

Last Answer : (C) Method of cross profile is used 

Pick up the method of surveying in which field observations and plotting proceed simultaneously from the following (A) Chain surveying (B) Compass surveying (C) Plan table surveying (D) Tacheometric surveying

Description : Pick up the method of surveying in which field observations and plotting proceed simultaneously from the following (A) Chain surveying (B) Compass surveying (C) Plan table surveying (D) Tacheometric surveying

Last Answer : (C) Plan table surveying

The limiting length of an offset does not depend upon (A) Accuracy of the work (B) Method of setting out perpendiculars (C) Scale of plotting (D) Indefinite features to be surveyed

Description : The limiting length of an offset does not depend upon (A) Accuracy of the work (B) Method of setting out perpendiculars (C) Scale of plotting (D) Indefinite features to be surveyed

Last Answer : (D) Indefinite features to be surveyed

In the cross-section method of indirect contouring, the spacing of cross-sections depends upon (i) Contour interval (ii) Scale of plan (iii) Characteristics of ground The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Description : In the cross-section method of indirect contouring, the spacing of cross-sections depends upon (i) Contour interval (ii) Scale of plan (iii) Characteristics of ground The correct answer is (A) Only (i) (B) (i) and (ii) (C) (ii) and (iii) (D) (i), (ii) and (iii)

Last Answer : (D) (i), (ii) and (iii)

Direct method of contouring is (A) A quick method (B) Adopted for large surveys only(C) Most accurate method (D) Suitable for hilly terrains

Description : Direct method of contouring is (A) A quick method (B) Adopted for large surveys only (C) Most accurate method (D) Suitable for hilly terrains

Last Answer : (C) Most accurate method

Which of the following methods of contouring is most suitable for a hilly terrain? (A) Direct method (B) Square method (C) Cross-sections method (D) Tachometric method

Description : Which of the following methods of contouring is most suitable for a hilly terrain? (A) Direct method (B) Square method (C) Cross-sections method (D) Tachometric method

Last Answer : (D) Tachometric method

Select the correct statement. A) Contour interval on any map is kept constant. (B) Direct method of contouring is cheaper than indirect method. (C) Intervisibility of points on a contour map cannot be ascertained. (D) Slope of a hill cannot be determined with the help of contours.

Description : Select the correct statement. . A) Contour interval on any map is kept constant. (B) Direct method of contouring is cheaper than indirect method. (C) Intervisibility of points on a contour map cannot be ascertained. (D) Slope of a hill cannot be determined with the help of contours.

Last Answer : (A) Contour interval on any map is kept constant.

The accuracy of measurement in chain surveying, does not depend upon (A) Length of the offset (B) Scale of the plotting (C) Importance of the features (D) General layout of the chain lines

Description : The accuracy of measurement in chain surveying, does not depend upon (A) Length of the offset (B) Scale of the plotting (C) Importance of the features (D) General layout of the chain lines

Last Answer : (D) General layout of the chain lines

Intersection method of detailed plotting is most suitable for (A) Forests (B) Urban areas (C) Hilly areas (D) Plains

Description : Intersection method of detailed plotting is most suitable for (A) Forests (B) Urban areas (C) Hilly areas (D) Plains

Last Answer : (C) Hilly areas

Which one of the following statements is not relevant to hydrographic survey? (A) Establishment of a chain of bench marks near the shore line (B) Establishment of horizontal control points on the shore (C) Determination of the sea bed profile (D) None of these

Description : Which one of the following statements is not relevant to hydrographic survey? (A) Establishment of a chain of bench marks near the shore line (B) Establishment of horizontal control points on the shore (C) Determination of the sea bed profile (D) None of these

Last Answer : (D) None of these

List any four accessories required for plane table survey.

Description : List any four accessories required for plane table survey.

Last Answer : 1. Plane table. 2. Plumbing U-fork. 3. Alidade. 4. Spirit level. 5. Trough compass. 6. Plumb bob.

List any four methods of plotting a compass traverse survey & explain any one in brief. Also state the meaning of adjustment of closing error of traverse.

Description : List any four methods of plotting a compass traverse survey & explain any one in brief. Also state the meaning of adjustment of closing error of traverse.

Last Answer : Methods of plotting compass traverse are: 1. By parallel meridian through each station. 2. By included angle. 3. By paper protractor. 4. By rectangular co-ordinates. 5. ... . 5. Finally join new points to get corrected traverse ABCDEA after graphical adjustment of closing error. 

The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error such that each ray is equally rotated either clockwise or anti clockwise 5. The points obtained by three rays are the correct location. The correct sequence is (A) 1, 3, 2, 4, 5 (B) 1, 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Description : The operation of resection involves the following steps 1. Rough orientation of the plane table 2. The three lines form a triangle of error 3. Drawing lines back through the three control points 4. Select a point in the triangle of error ... 2, 3, 4, 5 (C) 1, 4, 3, 2, 5 (D) 1, 3, 2, 4, 5

Last Answer : (A) 1, 3, 2, 4, 5

The instrument used for accurate centering in plane table survey is (A) Spirit level (B) Alidade (C) Plumbing fork (D) Trough compass

Description : The instrument used for accurate centering in plane table survey is (A) Spirit level (B) Alidade (C) Plumbing fork (D) Trough compass

Last Answer : (C) Plumbing fork

What are the different methods of contouring? Describe any one method along with sketch . Also write the situation where it is suitable

Description : What are the different methods of contouring? Describe any one method along with sketch . Also write the situation where it is suitable

Last Answer : There are two methods of contouring:- 1. Direct Method 2. Indirect Method - a. By squares  b. By cross section  c. By tacheometric Direct method of contouring - In this ... joining these identical coloured pegs, we get the required contours on ground by this direct method of contouring. 

Detailed plotting is generally done by (A) Radiation (B) Traversing (C) Resection (D) All of the above

Description : Detailed plotting is generally done by (A) Radiation (B) Traversing (C) Resection (D) All of the above

Last Answer : (A) Radiation

While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of the ray in plan from the true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Description : While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of ... true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Last Answer : (B) 0.15 cm

While working on a plane table, the correct rule is: (A) Draw continuous lines from all instrument stations (B) Draw short rays sufficient to contain the points sought (C) Intersection should be obtained by actually drawing second rays (D) Take maximum number of sights as possible from each station to distant objects

Description : While working on a plane table, the correct rule is: (A) Draw continuous lines from all instrument stations (B) Draw short rays sufficient to contain the points sought (C) Intersection ... drawing second rays (D) Take maximum number of sights as possible from each station to distant objects

Last Answer : (B) Draw short rays sufficient to contain the points sought

Pick up the correct statement from the following: (A) The directions of plumb lines suspended at different points in a survey are not strictly parallel (B) In surveys of small extent, the effect of curvature may be ignored and the level surface of the earth is assumed as horizontal (C) In surveys of large extent, the effect of curvature of the earth must be considered (D) All the above

Description : Pick up the correct statement from the following: (A) The directions of plumb lines suspended at different points in a survey are not strictly parallel (B) In surveys of small extent, the effect of ... of large extent, the effect of curvature of the earth must be considered (D) All the above

Last Answer : (D) All the above

On plotting the points 0(0, 0), A(3, 0), 5(3, 4), C(0, 4) and joining OA, AB, BC and CO. -Maths 9th

Description : On plotting the points 0(0, 0), A(3, 0), 5(3, 4), C(0, 4) and joining OA, AB, BC and CO. -Maths 9th

Last Answer : (b) Here, point 0 (0, 0) is the origin. A(3, 0) lies on positive direction of X-axis, B (3, 4) lies in 1st quadrant and C (0, 4) lines on positive direction of Y-axis. On joining OA AB, BC and CO the figure obtained is a rectangle.

Without plotting the points indicate the quadrant in which they will lie, if -Maths 9th

Description : Without plotting the points indicate the quadrant in which they will lie, if -Maths 9th

Last Answer : (i) The given point is (- 3, 5). Here, abscissa is negative and ordinate is positive, so it lies in II quadrant. (ii) The given point is (-5, - 3). Here, abscissa and ordinate both are negative ... ) The given point is (3, 5). Here, abscissa and ordinate both are positive, so it lies in I quadrant.

On plotting the points 0(0, 0), A(3, 0), 5(3, 4), C(0, 4) and joining OA, AB, BC and CO. -Maths 9th

Description : On plotting the points 0(0, 0), A(3, 0), 5(3, 4), C(0, 4) and joining OA, AB, BC and CO. -Maths 9th

Last Answer : (b) Here, point 0 (0, 0) is the origin. A(3, 0) lies on positive direction of X-axis, B (3, 4) lies in 1st quadrant and C (0, 4) lines on positive direction of Y-axis. On joining OA AB, BC and CO the figure obtained is a rectangle.

Without plotting the points indicate the quadrant in which they will lie, if -Maths 9th

Description : Without plotting the points indicate the quadrant in which they will lie, if -Maths 9th

Last Answer : (i) The given point is (- 3, 5). Here, abscissa is negative and ordinate is positive, so it lies in II quadrant. (ii) The given point is (-5, - 3). Here, abscissa and ordinate both are negative ... ) The given point is (3, 5). Here, abscissa and ordinate both are positive, so it lies in I quadrant.

Without plotting the points indicate the quadrant in which they will lie, if: -Maths 9th

Description : Without plotting the points indicate the quadrant in which they will lie, if: -Maths 9th

Last Answer : Solution :- (i) III quadrant (iii) IV quadrant

Without plotting the points indicate the quadrant in which they lie, if : (i) ordinate is 5 and abscissa is – 3 (ii) abscissa is -5 and ordinate is – 3 -Maths 9th

Description : Without plotting the points indicate the quadrant in which they lie, if : (i) ordinate is 5 and abscissa is – 3 (ii) abscissa is -5 and ordinate is – 3 -Maths 9th

Last Answer : answer:

Without plotting the points indicate the quadrant in which they will lie, if (i) the ordinate is 5 and abscissa is – 3 -Maths 9th

Description : Without plotting the points indicate the quadrant in which they will lie, if (i) the ordinate is 5 and abscissa is – 3 -Maths 9th

Last Answer : (i) In the point (−3,5) abscissa is negative and ordinate is positive, so it lies in the second quadrant. (ii) In the point (−5,−3) abscissa and ordinate both are negative, so it lies in the ... . (iv) In the point (3,5) abscissa and ordinate both are positive, so it lies in the first quadrant

When Santana is plotting points on a graph. The ratio of y y -value to x x -value is 3 3 to 4 4 for each point. What will be the x x -value of a point with a y y -value of 12 12?

Description : When Santana is plotting points on a graph. The ratio of y y -value to x x -value is 3 3 to 4 4 for each point. What will be the x x -value of a point with a y y -value of 12 12?

Last Answer : It will be 16.

53. While plotting constraints on a graph paper, terminal points on both the axes are connected by straight line because a. The resources are limited in supply b. The objective function as a linear function c. The constraints are linear equations or inequalities d. All of the above

Description : 53. While plotting constraints on a graph paper, terminal points on both the axes are connected by straight line because a. The resources are limited in supply b. The objective function as a linear function c. The constraints are linear equations or inequalities d. All of the above

Last Answer : c. The constraints are linear equations or inequalities

Differentiate between plane and geodetic survey on any four points.

Description : Differentiate between plane and geodetic survey on any four points. 

Last Answer : Difference between Plane Surveying and Geodetic Surveying Points Plane Surveying Geodetic Surveying Definition Plane surveying is that type of surveying in which mean surface of ... Traditional survey equipment is used Precise and modern survey equipment are required

The 'fix' of a plane table station with three known points, is bad if the plane table station lies (A) In the great triangle (B) Outside the great triangle (C) On the circumference of the circumscribing circle (D) None of these

Description : The 'fix' of a plane table station with three known points, is bad if the plane table station lies  (A) In the great triangle  (B) Outside the great triangle  (C) On the circumference of the circumscribing circle  (D) None of these 

Last Answer : (C) On the circumference of the circumscribing circle 

The 'fix' of a plane table from three known points, is good, if (A) Middle station is nearest (B) Middle station is farthest (C) Either the right or left station is nearest (D) None of these

Description : The 'fix' of a plane table from three known points, is good, if  (A) Middle station is nearest  (B) Middle station is farthest  (C) Either the right or left station is nearest  (D) None of these 

Last Answer : (A) Middle station is nearest 

Orientation of a plane table by solving two point problems is only adopted when (A) Saving of time is a main factor (B) Better accuracy is a main factor (C) Given points are inaccessible (D) None of these

Description : Orientation of a plane table by solving two point problems is only adopted when (A) Saving of time is a main factor (B) Better accuracy is a main factor (C) Given points are inaccessible (D) None of these

Last Answer : (C) Given points are inaccessible

Locating the position of a plane table station with reference to three known points, is known as (A) Intersection method (B) Radiation method (C) Resection method (D) Three point problem

Description : Locating the position of a plane table station with reference to three known points, is known as (A) Intersection method (B) Radiation method (C) Resection method (D) Three point problem

Last Answer : (D) Three point problem

To orient a plane table at a point with two inaccessible points, the method generally adopted, is (A) Intersection (B) Resection (C) Radiation (D) Two point problem

Description : To orient a plane table at a point with two inaccessible points, the method generally adopted, is (A) Intersection (B) Resection (C) Radiation (D) Two point problem

Last Answer : (D) Two point problem

Which of the instruments is not used in Preliminary survey. (a) Theodelite (b) Tacheometer (c) Dumpy level (d) Plane table (e) None of them*

Description : Which of the instruments is not used in Preliminary survey. (a) Theodelite (b) Tacheometer (c) Dumpy level (d) Plane table (e) None of them*

Last Answer : (e) None of them*

State advantages of plane table survey one each with respect to booking and suitability

Description : State advantages of plane table survey one each with respect to booking and suitability

Last Answer : Booking of observations: i) Field work and plotting work done simultaneously ii) ) Notes of measurement are seldom required and possibility of mistakes in booking is eliminated. Suitability of PT ... and work where great accuracy is not required. ii) Mostly suitable for survey in plain terrain

Explain the radiation method of plane table survey with neat sketch.

Description : Explain the radiation method of plane table survey with neat sketch. 

Last Answer : This method is used when all the points to be plotted are visible from single instrument station. Steps are: 1. Select a suitable point P on the ground such that all the details are visible from it. 2. Center and ... , pc, pd, pe respectively. Join a, b, c, d, and e to give the outline.

State merits and demerits of plane table survey.

Description : State merits and demerits of plane table survey. 

Last Answer : Merits: 1) It is the most rapid method of surveying.  2)There is no need for field book as plotting is done along with the field work, so the problem of mistakes in booking field notes does not arise. ... to carry. 5) The map cannot be replotted to defferent scale as there is no field book. 

State the principle of plane table survey.

Description : State the principle of plane table survey. 

Last Answer : Principle of plane table survey 1. The rays drawn from different points should pass through a single point i.e. position of station point.  2. The position of table should be same as that of previous station i.e. orientation should be done at each changed station.

State four advantages and four disadvantages of plane table survey

Description : State four advantages and four disadvantages of plane table survey

Last Answer : Advantages: 1. A field book is not required. 2. Errors of booking in field book avoided. 3. Errors of plotting can be readily checked. 4. Suitable in magnetic area. 5. Survey work with ... cannot be done in rainy season. 5. Difficult to re-plot as field notes are not available.

Explain temporary adjustment of plane table survey.

Description : Explain temporary adjustment of plane table survey.

Last Answer : 1. Setting over the station: The plane table is fixed on tripod and adjust the table in such a way that table is approximately level. 2. Leveling the table: The tubular or spirit level is placed in two ... . The table can be oriented in two ways. i. Using trough compass. ii. By back sighting.

Describe in brief errors in plane table survey.

Description : Describe in brief errors in plane table survey.

Last Answer : 1) The board not being horizontal. 2) The table not being accurately centered. 3) The table not being Correctly oriented. 4) The objects not being sited accurately. 5) The alidade not being ... through the station point. 7) Inaccuracy in plotting. 8) The expansion and contraction of the paper.

Enlist different accessories of plane table survey with their use.

Description : Enlist different accessories of plane table survey with their use. 

Last Answer : i) The plane table: It is used for fixing a drawing sheet over it.  To locate the position of the objects on the sheet by drawing rays and plotting to suitable scale. ii) The Alidade (plain Alidade ... v) U-Fork or Plumbing fork with plumb bob: It is used for centering the table over the station. 

State the suitability of plane table survey

Description : State the suitability of plane table survey

Last Answer : The plane tabling is generally suitable for surveys in which high precision is not required. It is mainly employed for small-scale or medium size mapping.