While surveying a plot of land by plane tabling, the field observations (A) And plotting proceed simultaneously (B) And plotting do not proceed simultaneously (C) And recorded in field books to be plotted later (D) All the above

While surveying a plot of land by plane tabling, the field observations
(A) And plotting proceed simultaneously
(B) And plotting do not proceed simultaneously
(C) And recorded in field books to be plotted later
(D) All the above
by

1 Answer

Answer :

(A) And plotting proceed simultaneously
by

Related questions

Pick up the method of surveying in which field observations and plotting proceed simultaneously from the following (A) Chain surveying (B) Compass surveying (C) Plan table surveying (D) Tacheometric surveying

Description : Pick up the method of surveying in which field observations and plotting proceed simultaneously from the following (A) Chain surveying (B) Compass surveying (C) Plan table surveying (D) Tacheometric surveying

Last Answer : (C) Plan table surveying

Angles to a given pivot station observed from a number of traverse stations when plotted, the lines to the pivot station intersect at a common point (A) Angular measurements are correct and not the linear measurements (B) Linear measurements are correct and not the angular measurements (C) Angular and linear measurements are correct and not the plotting of traverse (D) Angular and linear measurements and also plotting of the traverse are correct

Description : Angles to a given pivot station observed from a number of traverse stations when plotted, the lines to the pivot station intersect at a common point (A) Angular measurements are correct and ... plotting of traverse (D) Angular and linear measurements and also plotting of the traverse are correct

Last Answer : (D) Angular and linear measurements and also plotting of the traverse are correct

The accuracy of measurement in chain surveying, does not depend upon (A) Length of the offset (B) Scale of the plotting (C) Importance of the features (D) General layout of the chain lines

Description : The accuracy of measurement in chain surveying, does not depend upon (A) Length of the offset (B) Scale of the plotting (C) Importance of the features (D) General layout of the chain lines

Last Answer : (D) General layout of the chain lines

The distances AC and BC are measured from two fixed points A and B whose distance AB is known. The point C is plotted by intersection. This method is generally adopted in (A) Chain surveying (B) Traverse method of surveys (C) Triangulation (D) None of these

Description : The distances AC and BC are measured from two fixed points A and B whose distance AB is known. The point C is plotted by intersection. This method is generally adopted in (A) Chain surveying (B) Traverse method of surveys (C) Triangulation (D) None of these

Last Answer : (A) Chain surveying

Regarding plane-table survey, which of the following statements does not hold? (a) All the plotting work including contouring can be done in the field (b) It is quite suitable for small scale survey (c) Less number of control points are required (d) It can be done in all seasons

Description : Regarding plane-table survey, which of the following statements does not hold? (a) All the plotting work including contouring can be done in the field (b) It is quite suitable for small scale survey (c) Less number of control points are required (d) It can be done in all seasons

Last Answer : (d) It can be done in all seasons

The branch of surveying in which both horizontal and vertical positions of a point, are determined by making instrumental observations, is known (A) Tacheometry (B) Tachemetry (C) Telemetry (D) All the above

Description : The branch of surveying in which both horizontal and vertical positions of a point, are determined by making instrumental observations, is known (A) Tacheometry (B) Tachemetry (C) Telemetry (D) All the above

Last Answer : (D) All the above

Pick up the correct statement from the following: (A) Hydrograph is a plot of discharge and time (B) In hydrographs, time is plotted on X-axis (C) The maximum flow in the river due to rainfall, is called peak flow (D) All the above

Description : Pick up the correct statement from the following: (A) Hydrograph is a plot of discharge and time (B) In hydrographs, time is plotted on X-axis (C) The maximum flow in the river due to rainfall, is called peak flow (D) All the above

Last Answer : Answer: Option D

One of the Lehmann's rules of plane tabling, is (A) Location of the instrument station is always distant from each of the three rays from the known points in proportion to their distances (B) When looking in the direction of each of the given points, the instrument station will be on the right side of one and left side of the other ray (C) When the instrument station is outside the circumscribing circle its location is always on the opposite side of the ray to the most distant point as the inter-section of the other two rays (D) None of these

Description : One of the Lehmann's rules of plane tabling, is  (A) Location of the instrument station is always distant from each of the three rays from the  known points in proportion to their distances  ( ... to the most distant point as the inter-section of the other two rays  (D) None of these 

Last Answer : (A) Location of the instrument station is always distant from each of the three rays from the  known points in proportion to their distances 

Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Description : Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Last Answer : (D) Resection

The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Description : The instrument which is used in plane tabling for obtaining horizontal and vertical distances directly without resorting to chaining, is known as (A) Plane alidade (B) Telescopic alidade (C) Clinometer (D) Tacheometer

Last Answer : (B) Telescopic alidade

Check lines (or proof lines) in Chain Surveying, are essentially required (A) To plot the chain lines (B) To plot the offsets (C) To indicate the accuracy of the survey work (D) To increase the out-turn

Description : Check lines (or proof lines) in Chain Surveying, are essentially required (A) To plot the chain lines (B) To plot the offsets (C) To indicate the accuracy of the survey work (D) To increase the out-turn

Last Answer : (C) To indicate the accuracy of the survey work

The plotting of inaccessible points in a plane-table survey can be done by the method of (a) Interpolation (b) Radiation (c) Intersection (d) Traversing

Description : The plotting of inaccessible points in a plane-table survey can be done by the method of (a) Interpolation (b) Radiation (c) Intersection (d) Traversing

Last Answer : (c) Intersection

In a plane-table survey, the process of determining the plotted position of a station occupied by the plane-table by means of sights taken towards known points, the locations of which have already been plotted, is known as (a) Radiation (b) Resection (c) Intersection (d) Traversing

Description : In a plane-table survey, the process of determining the plotted position of a station occupied by the plane-table by means of sights taken towards known points, the locations of which have already been plotted, is known as (a) Radiation (b) Resection (c) Intersection (d) Traversing

Last Answer : (b) Resection

Compressibility factor-reduced pressure plot on reduced co-ordinates facilitates (A) Use of only one graph for all gases (B) Covering of wide range (C) Easier plotting (D) More accurate plotting

Description : Compressibility factor-reduced pressure plot on reduced co-ordinates facilitates (A) Use of only one graph for all gases (B) Covering of wide range (C) Easier plotting (D) More accurate plotting

Last Answer : A) Use of only one graph for all gases

The method generally preferred to for contouring an undulating area, is (A) Chain surveying (B) Plane table surveying (C) Tacheometrical surveying (D) Compass surveying

Description : The method generally preferred to for contouring an undulating area, is (A) Chain surveying (B) Plane table surveying (C) Tacheometrical surveying (D) Compass surveying

Last Answer : (C) Tacheometrical surveying

The type of surveying which requires least office work is (A) Tachometry (B) Trigonometrical levelling (C) Plane table surveying (D) Theodolite surveying

Description : The type of surveying which requires least office work is (A) Tachometry (B) Trigonometrical levelling (C) Plane table surveying (D) Theodolite surveying

Last Answer : (C) Plane table surveying

Which of the following methods of plane table surveying is used to locate the position of an inaccessible point? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Description : Which of the following methods of plane table surveying is used to locate the position of an inaccessible point? (A) Radiation (B) Intersection (C) Traversing (D) Resection

Last Answer : (B) Intersection

In a solution of the three-point problem in plane table surveying, the converging of error is attained through : (a) Concyclic concept (b) Bessel’s method (c) Triangle of error (d) Tracing paper method

Description : In a solution of the three-point problem in plane table surveying, the converging of error is attained through : (a) Concyclic concept (b) Bessel’s method (c) Triangle of error (d) Tracing paper method

Last Answer : (c) Triangle of error

The method of plane tabling commonly used for establishing the instrument station is a method of (a) Radiation (b) Intersection* (c) Resection (d) Traversing

Description : The method of plane tabling commonly used for establishing the instrument station is a method of (a) Radiation (b) Intersection* (c) Resection (d) Traversing

Last Answer : (b) Intersection*

Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Description : Write any four advantages of intersection method of plane tabling over radiation method of plane tabling.

Last Answer : Advantages of intersection method: 1. Interection method requires less ground distance measurement than radiation method. 2. By this method we can locate inaccessible points which cannot be ... to radiation method, intersection method eliminates undulation error, bisection error and plotting errors.

Explain errors occurred due to manipulation and sighting in plane tabling.

Description : Explain errors occurred due to manipulation and sighting in plane tabling.

Last Answer : i) The board not being horizontal- This error affects chiefly the measurement of vertical angles. ii) The table not being accurately centered. The plotted position of the occupied station not ... and correct any displacement. v) The defective sighting- The object not being correctly sighted.

Define orientation and principle of plane tabling.

Description : Define orientation and principle of plane tabling. 

Last Answer : Orientation: The orientation of plane table means keeping the plane table at all stations parallel to the position it occupied at first station. Principles of plane table survey: 1. The rays drawn from ... same as that of previous station i.e. orientation should be done at each changed station.  

Enlist the methods of plane tabling.

Description : Enlist the methods of plane tabling. 

Last Answer : Method of Surveying with the plane table are : 1) Radiation 2) Intersection 3) Traversing 4) Resection

Explain with neat sketch the procedure of radiation method of plane tabling.

Description : Explain with neat sketch the procedure of radiation method of plane tabling.

Last Answer : 1. The table is set at suitable station e.g. P from where all stations can be sighted and measured. 2. After centering and leveling, mark station P as P' on sheet. 3. Suppose stations A, B, C, and D are ... marked as pa. 5. Similarly station B, C and D are bisected and marked as b, c and d.

What are the sources of errors in plane tabling?

Description : What are the sources of errors in plane tabling?

Last Answer : The following are the sources of errors in plane tabling 1) The board not being horizontal 2) The table not being accurately centered 3) The table not being Correctly oriented 4) The objects ... through the station point 7) Inaccuracy in plotting 8) The expansion and contraction of the paper 

A sample of water from a river was analyzed for the presence of metal ions and the observations were recorded as given below `{:("Reagent added","Obse

Description : A sample of water from a river was analyzed for the presence of metal ions and the observations were recorded as given below `{:("Reagent added","Obse

Last Answer : A sample of water from a river was analyzed for the presence of metal ions and the observations were recorded as given ... C. `Li^(+)` D. `Mg^(2+)`

What is information from an experiment such as observations or behaviors that cannot be recorded with a numerical value.?

Description : What is information from an experiment such as observations or behaviors that cannot be recorded with a numerical value.?

Last Answer : Qualitative Data

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

In chain surveying field work is limited to (A) Linear measurements only (B) Angular measurements only (C) Both linear and angular measurements (D) All the above

Description : In chain surveying field work is limited to (A) Linear measurements only (B) Angular measurements only (C) Both linear and angular measurements (D) All the above

Last Answer : (A) Linear measurements only

Two coal trains, one southbound, the other westbound, reach an over and under crossing at the same instant and each proceed at 40 kilometers per hour on their respective courses. Approximately how far apart are the lead cars two hours later, to the nearest kilometer? w) 80 x) 113 y) 136 z) 160

Description : Two coal trains, one southbound, the other westbound, reach an over and under crossing at the same instant and each proceed at 40 kilometers per hour on their respective courses. Approximately how far apart are the lead cars two hours later, to the nearest kilometer? w) 80 x) 113 y) 136 z) 160

Last Answer : ANSWER: X -- 113 

Is it true that in the late 1500s Ptolemy's observations were supplanted by those of later Greek astronomers?

Description : Is it true that in the late 1500s Ptolemy's observations were supplanted by those of later Greek astronomers?

Last Answer : Later polish astronomers

A block A is dropped down a smooth inclined plane, while another identical block B is released for free fall from the same height a.block A will have higher velocity than block B while hitting the ground b.block B will hit the ground earlier. c.both will hit the ground simultaneously d.block A will hit the ground earlier e.107 dynes

Description : A block A is dropped down a smooth inclined plane, while another identical block B is released for free fall from the same height a.block A will have higher velocity than block B while hitting the ... . c.both will hit the ground simultaneously d.block A will hit the ground earlier e.107 dynes

Last Answer : b. block B will hit the ground earlier.

Which of the following is not an application of Green’s theorem? a) Solving two dimensional flow integrals b) Area surveying c) Volume of plane figures d) Centroid of plane figures

Description : Which of the following is not an application of Green’s theorem? a) Solving two dimensional flow integrals b) Area surveying c) Volume of plane figures d) Centroid of plane figures

Last Answer : c) Volume of plane figures

Compare radiation and intersection methods of plane table surveying on any two parameters.

Description : Compare radiation and intersection methods of plane table surveying on any two parameters. 

Last Answer : Radiation method Intersection method 1. It requires the plane table to occupy a single station.  1. This method requires setting the table up at minimum of two stations.  ... for locating inaccessible points by the intersection of the rays drawn from two instruments stations. 

Describe any one method of orientation of plane table surveying

Description : Describe any one method of orientation of plane table surveying

Last Answer : Orientation by back sighting method: This method is accurate and is always preferred. Procedure: 1.Suppose A and B are two stations.The plane table is set up over A. The table is leveled by spirit level ... are perfect and needle is exactly at 0-0 , the orientation is said to be perfect.

State two advantages of plane table surveying

Description : State two advantages of plane table surveying

Last Answer : 1.it is most rapid method of surveying. 2. it is suitable for magnetic areas. 3.The map can be prepared easily ,and does not require greater skill. 4.Irregular objects can be represented ... is less costly. 7 The check lines detects the errors of measurement and plotting on field itself. 

Draw sketch and explain method of traversing of plane table surveying.

Description : Draw sketch and explain method of traversing of plane table surveying. 

Last Answer : Procedure: 1.Set plane table over station A use plumbing fork for transferring station point from ground on sheet. Draw the direction of magnetic meridian with the help of compass. 2. With the ... scale Similarly, the table can be set at other successive station and traverse is completed.

Describe back sighting method of orientation of plane table surveying.

Description : Describe back sighting method of orientation of plane table surveying.

Last Answer : Backsight method of orientation 1. Assume we have to orient the table at next station B' represented on paper by point b'. 2.the line ba' is drawn on previous station A'. 3.the alidade is kept ... A'. 4. When the plotted line ab' coincides with line AB' and table will be oriented.

State any two uses of Plane Surveying.

Description : State any two uses of Plane Surveying. 

Last Answer : 1) Plane surveying is used for measuring small distance. 2) When area is less than 260 km2, plane survey is normally done. 3) When desired accuracy is less, plane survey is done.

Explain ‘Intersection Method’ of plane table surveying with neat sketch. Also give situation when intersection method is used.

Description : Explain ‘Intersection Method’ of plane table surveying with neat sketch. Also give situation when intersection method is used.

Last Answer : 1. Lay out a base line AB and measure it and Plot a distance ab' on sheet using any scale. 2.Set up instrument at A' with a' over A' 3.Orient the table by placing alidade ... the case of the survey of mountainous country. 5. The only linear measurement required is that of a base line.

State the use of alidade in plane table surveying

Description : State the use of alidade in plane table surveying

Last Answer : 1) It is used for sighting the objects to be located.  2) It is used for drawing the rays. 

State the limitations of plane table surveying.

Description : State the limitations of plane table surveying.

Last Answer : 1) It is not suitable for work in wet climate 2) Several accessories are required to be carried hence possibility lost. 3) Replotting of survey work to different scale is difficult in absence of ... ) It is not intended for accurate work. 6) The plane table is essentially a tropical instrument.

Describe in brief resection method of plane table surveying.

Description : Describe in brief resection method of plane table surveying.

Last Answer : This method is used for establishing the instrument stations only. After fixing the stations, details are located either by radiation or intersection. The characteristic feature of resection is that the point ... of resection are (1)The Two Point Problem, and (2)Three Point Problem.

In setting up a plane table at any station (A) Levelling is done first (B) Centering is done first (C) Both levelling and centering are done simultaneously (D) Orientation is done first

Description : In setting up a plane table at any station (A) Levelling is done first (B) Centering is done first (C) Both levelling and centering are done simultaneously (D) Orientation is done first

Last Answer : (C) Both levelling and centering are done simultaneously

The radiation pattern plotted in terms of electric field strength or power density

Description : The radiation pattern plotted in terms of electric field strength or power density

Last Answer : absolute radiation pattern

Which of the following statement is correct? (A) The amount of Goodwill or Capital Reserve is recorded in the books of purchasing company only (B) The amount of Goodwill or Capital Reserve is recorded in the books of vendor company only. (C) Goodwill = Net Assets – Purchase price (D) The face value of shares of purchasing company will be taken in to account while calculating purchase consideration.

Description : Which of the following statement is correct? (A) The amount of Goodwill or Capital Reserve is recorded in the books of purchasing company only (B) The amount of Goodwill or Capital ... value of shares of purchasing company will be taken in to account while calculating purchase consideration.

Last Answer : The amount of Goodwill or Capital Reserve is recorded in the books of purchasing company only

53. While plotting constraints on a graph paper, terminal points on both the axes are connected by straight line because a. The resources are limited in supply b. The objective function as a linear function c. The constraints are linear equations or inequalities d. All of the above

Description : 53. While plotting constraints on a graph paper, terminal points on both the axes are connected by straight line because a. The resources are limited in supply b. The objective function as a linear function c. The constraints are linear equations or inequalities d. All of the above

Last Answer : c. The constraints are linear equations or inequalities

The most reliable method of plotting a theodolite traverse, is (A) By consecutive co-ordinates of each station (B) By independent co-ordinates of each station (C) By plotting included angles and scaling off each traverse leg (D) By the tangent method of plotting

Description : The most reliable method of plotting a theodolite traverse, is (A) By consecutive co-ordinates of each station (B) By independent co-ordinates of each station (C) By plotting included angles and scaling off each traverse leg (D) By the tangent method of plotting

Last Answer : (B) By independent co-ordinates of each station

The limiting length of an offset does not depend upon (A) Accuracy of the work (B) Method of setting out perpendiculars (C) Scale of plotting (D) Indefinite features to be surveyed

Description : The limiting length of an offset does not depend upon (A) Accuracy of the work (B) Method of setting out perpendiculars (C) Scale of plotting (D) Indefinite features to be surveyed

Last Answer : (D) Indefinite features to be surveyed

Intersection method of detailed plotting is most suitable for (A) Forests (B) Urban areas (C) Hilly areas (D) Plains

Description : Intersection method of detailed plotting is most suitable for (A) Forests (B) Urban areas (C) Hilly areas (D) Plains

Last Answer : (C) Hilly areas