The efficiency of Diesei cycle with decrease in cut off  (a) increases  (b) decreases  (c) remains unaffected  (d) first increases and then decreases  (e) first decreases and then increases.

The efficiency of Diesei cycle with decrease in cut off
 (a) increases
 (b) decreases
 (c) remains unaffected
 (d) first increases and then decreases
 (e) first decreases and then increases.
by

1 Answer

Answer :

Answer : a
by

Related questions

The efficiency of Diesel cycle increases with  A. decrease in cut-off  B. increase in cut-off  C. constant cut-off  D. none of these

Description : The efficiency of Diesel cycle increases with  A. decrease in cut-off  B. increase in cut-off  C. constant cut-off  D. none of these

Last Answer : Answer: A

In an isothermal process, the internal energy of gas molecules  (a) increases  (b) decreases  (c) remains constant  (d) may increase/decrease depending on the properties of gas  (e) shows unpredictable behaviour.

Description : In an isothermal process, the internal energy of gas molecules  (a) increases  (b) decreases  (c) remains constant  (d) may increase/decrease depending on the properties of gas  (e) shows unpredictable behaviour.

Last Answer : Answer : c

In an isothermal process, the internal energy  (a) increases  (b) decreases  (c) remains constant  (d) first increases and then decreases  (e) first decreases and then increases.

Description : In an isothermal process, the internal energy  (a) increases  (b) decreases  (c) remains constant  (d) first increases and then decreases  (e) first decreases and then increases.

Last Answer : Answer : c

The efficiency of Diesel cycle depends upon  A. temperature limits  B. pressure ratio  C. compression ratio  D. cut-off ratio and compression ratio

Description : The efficiency of Diesel cycle depends upon  A. temperature limits  B. pressure ratio  C. compression ratio  D. cut-off ratio and compression ratio

Last Answer : Answer: D

The efficiency of a dual combustion cycle __________ upon cut-off ratio.  A. depends  B. does not depend

Description : The efficiency of a dual combustion cycle __________ upon cut-off ratio.  A. depends  B. does not depend

Last Answer : Answer: A

When cut-off ratio is __________ the efficiency of Diesel cycle approaches to Otto cycle efficiency.  A. zero  B. 1/5  C. 4/5  D. 1

Description : When cut-off ratio is __________ the efficiency of Diesel cycle approaches to Otto cycle efficiency.  A. zero  B. 1/5  C. 4/5  D. 1

Last Answer : Answer: A

The efficiency of Diesel cycle approaches to Otto cycle efficiency when  A. cut-off is increased  B. cut-off is decreased  C. cut-off is zero  D. cut-off is constant

Description : The efficiency of Diesel cycle approaches to Otto cycle efficiency when  A. cut-off is increased  B. cut-off is decreased  C. cut-off is zero  D. cut-off is constant

Last Answer : Answer: C

The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will  (a) increase  (b) decrease  (c) remain unchanged  (d) increase/decrease depending on ap-plication  (e) unpredictable. “

Description : The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will  (a) increase  (b) decrease  (c) remain unchanged  (d) increase/decrease depending on ap-plication  (e) unpredictable. “

Last Answer : Answer : b

An ideal gas is compressed in a cylinder so well insulated that there is essentially no heat transfer. The temperature of gas  a. Remains constant  b. increases  c. decreases  d. is basically zero

Description : An ideal gas is compressed in a cylinder so well insulated that there is essentially no heat transfer. The temperature of gas  a. Remains constant  b. increases  c. decreases  d. is basically zero

Last Answer : increases

When liquid water is converted to steam at 100˚C, the entropy of water  a. increases  b. decreases  c. remains the same  d. none of the above

Description : When liquid water is converted to steam at 100˚C, the entropy of water  a. increases  b. decreases  c. remains the same  d. none of the above

Last Answer : increases

On a day when the partial pressure of water vapor remains constant, what happens as the temperature rises?  a. the relative humidity increases  b. the relative humidity decreases  c. the relative humidity remains constant  d. the air would eventually become saturated

Description : On a day when the partial pressure of water vapor remains constant, what happens as the temperature rises?  a. the relative humidity increases  b. the relative humidity decreases  c. the relative humidity remains constant  d. the air would eventually become saturated

Last Answer : the relative humidity decreases

The volume of a given amount of water _________ as the temperature decreases from 4˚C to 0˚C.  a. decreases  b. increases  c. remains constant  d. none of the above

Description : The volume of a given amount of water _________ as the temperature decreases from 4˚C to 0˚C.  a. decreases  b. increases  c. remains constant  d. none of the above

Last Answer : increases

The entropy __________ in an irreversible cyclic process.  A. remains constant  B. decreases  C. increases

Description : The entropy __________ in an irreversible cyclic process.  A. remains constant  B. decreases  C. increases

Last Answer : Answer: C

If both Stirling and Carnot cycles operate within the same temperature limits, then efficiency of Stirling cycle as compared to Carnot cycle  (a) more  (b) less  (c) equal  (d) depends on other factors  (e) none of the above.

Description : If both Stirling and Carnot cycles operate within the same temperature limits, then efficiency of Stirling cycle as compared to Carnot cycle  (a) more  (b) less  (c) equal  (d) depends on other factors  (e) none of the above.

Last Answer : Answer : c

The more effective way of increasing efficiency of Carnot engine is to  (a) increase higher temperature  (b) decrease higher temperature  (c) increase lower temperature  (d) decrease lower temperature  (e) keep lower temperature constant.

Description : The more effective way of increasing efficiency of Carnot engine is to  (a) increase higher temperature  (b) decrease higher temperature  (c) increase lower temperature  (d) decrease lower temperature  (e) keep lower temperature constant.

Last Answer : Answer : d

The door of a running refrigerator inside a room was left open. Which of the following statements is correct?  (a) The room will be cooled to the temperature inside the refrigerator.  (b) The room will be cooled very slightly.  (c) The room will be gradually warmed up.  (d) The temperature of the air in room will remain unaffected.  (e) any one of above is possible depending on the capacity.

Description : The door of a running refrigerator inside a room was left open. Which of the following statements is correct?  (a) The room will be cooled to the temperature inside the refrigerator.  (b) The room ... air in room will remain unaffected.  (e) any one of above is possible depending on the capacity.

Last Answer : Answer : c

How the interest-level of a country is affected by FDI? (1) increases (2) decreases (3) remains unaffected (4) there is increase or decrease

Description : How the interest-level of a country is affected by FDI? (1) increases (2) decreases (3) remains unaffected (4) there is increase or decrease

Last Answer : (2) decreases Explanation: A higher international interest rate will decrease FDI since it means a higher cost of fund in international market, and vice versa. Interest rate is a measure of the cost of capital ... to a decrease in FDI. Interest rate and FDI can both be the cause and effect of other.

How the interest-level of a country is affected by FDI ? (1) increases (2) decreases (3) remains unaffected (4) there is increase or decrease

Description : How the interest-level of a country is affected by FDI ? (1) increases (2) decreases (3) remains unaffected (4) there is increase or decrease

Last Answer : decreases

The efficiency of Carnot cycle is maximum for  (a) gas engine  (b) well lubricated engine  (c) petrol engine  (d) steam engine  (e) reversible engine.

Description : The efficiency of Carnot cycle is maximum for  (a) gas engine  (b) well lubricated engine  (c) petrol engine  (d) steam engine  (e) reversible engine.

Last Answer : Answer : e

For same compression ratio and for same heat added  (a) Otto cycle is more efficient than Diesel cycle  (b) Diesel cycle is more efficient than Otto cycle  (c) efficiency depends on other factors  (d) both Otto and Diesel cycles are equally efficient  (e) none of the above.

Description : For same compression ratio and for same heat added  (a) Otto cycle is more efficient than Diesel cycle  (b) Diesel cycle is more efficient than Otto cycle  (c) efficiency depends on other factors  (d) both Otto and Diesel cycles are equally efficient  (e) none of the above.

Last Answer : Answer : a

An actual engine is to be designed having same efficiency as the Carnot cycle. Such a proposition is  (a) feasible  (b) impossible  (c) possible  (d) possible, but with lot of sophistications  (e) desirable.

Description : An actual engine is to be designed having same efficiency as the Carnot cycle. Such a proposition is  (a) feasible  (b) impossible  (c) possible  (d) possible, but with lot of sophistications  (e) desirable.

Last Answer : Answer : d

Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Description : Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Last Answer : Answer : b

Carnot cycle efficiency depends upon  (a) properties of the medium/substance used  (b) condition of engine  (c) working condition  (d) temperature range of operation  (e) effectiveness of insulating material around the engine.

Description : Carnot cycle efficiency depends upon  (a) properties of the medium/substance used  (b) condition of engine  (c) working condition  (d) temperature range of operation  (e) effectiveness of insulating material around the engine.

Last Answer : Answer : d

Carnot cycle has maximum efficiency for  (a) reversible engine  (b) irreversible engine  (c) new engine  (d) petrol engine  (e) diesel engine.

Description : Carnot cycle has maximum efficiency for  (a) reversible engine  (b) irreversible engine  (c) new engine  (d) petrol engine  (e) diesel engine.

Last Answer : Answer : a

What is a process in which the system remains infinitesimally closed to an equilibrium state at all times?  A. Path equilibrium process  B. Cycle equilibrium process  C. Phase equilibrium process  D. Quasi-state or quasiequilibrium process

Description : What is a process in which the system remains infinitesimally closed to an equilibrium state at all times?  A. Path equilibrium process  B. Cycle equilibrium process  C. Phase equilibrium process  D. Quasi-state or quasiequilibrium process

Last Answer : Quasi-state or quasi- equilibrium process

_____ is that property of a substance which remains constant if no heat enters or leaves the substance, while it does work or alters its volume, but which increases or diminishes should a small amount of heat enter or leave.  a. Entrophy  b. Enthalpy  c. Specific Heat  d. None of the above

Description : _____ is that property of a substance which remains constant if no heat enters or leaves the substance, while it does work or alters its volume, but which increases or diminishes should a small amount of heat enter or leave.  a. Entrophy  b. Enthalpy  c. Specific Heat  d. None of the above

Last Answer : Entrophy

In a free expansion process  (a) work done is zero  (b) heat transfer is zero  (c) both (a) and (b) above  (d) work done is zero but heat increases  (e) work done is zero but heat decreases.

Description : In a free expansion process  (a) work done is zero  (b) heat transfer is zero  (c) both (a) and (b) above  (d) work done is zero but heat increases  (e) work done is zero but heat decreases.

Last Answer : Answer : c

Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Description : Otto cycle efficiency is higher than Diesel cycle efficiency for the same compression ratio and heat input because in Otto cycle  A. combustion is at constant volume  B. expansion and compression are isentropic  C. maximum temperature is higher  D. heat rejection is lower

Last Answer : Answer: D

The efficiency of Joule cycle is  A. greater than Carnot cycle  B. less than Carnot cycle  C. equal to Carnot cycle  D. none of these

Description : The efficiency of Joule cycle is  A. greater than Carnot cycle  B. less than Carnot cycle  C. equal to Carnot cycle  D. none of these

Last Answer : Answer: B

The efficiency of Stirling cycle is __________ Carnot cycle.  A. greater than  B. less than  C. equal to

Description : The efficiency of Stirling cycle is __________ Carnot cycle.  A. greater than  B. less than  C. equal to

Last Answer : Answer: C

The efficiency and work ratio of a simple gas turbine cycle are  A.low  B.very low  C.high  D.very high

Description : The efficiency and work ratio of a simple gas turbine cycle are  A.low  B.very low  C.high  D.very high

Last Answer : Answer: B

As we heat a gas at constant pressure, its volume  a. increases  b. decreases  c. stays the same  d. none of the above

Description : As we heat a gas at constant pressure, its volume  a. increases  b. decreases  c. stays the same  d. none of the above

Last Answer : increases

When a solid melts,  a. the temperature of the substance increases.  b. the temperature of the substance decreases.  c. heat leaves the substance.  d. heat enters the substance.

Description : When a solid melts,  a. the temperature of the substance increases.  b. the temperature of the substance decreases.  c. heat leaves the substance.  d. heat enters the substance.

Last Answer : heat enters the substance.

The volume of a gas under constant pressure increases or decrease with temperature.  a. Gay- Lussac’s Law  b. Ideal Gas Law  c. Charles’ Law  d. Boyle’s Law

Description : The volume of a gas under constant pressure increases or decrease with temperature.  a. Gay- Lussac’s Law  b. Ideal Gas Law  c. Charles’ Law  d. Boyle’s Law

Last Answer : Charles’ Law

If a system after undergoing a series of processes, returns to the initial state then  (a) process is thermodynamically in equilibrium  (b) process is executed in closed system cycle  (c) its entropy will change due to irreversibility  (d) sum of heat and work transfer will be zero  (e) no work will be done by the system.

Description : If a system after undergoing a series of processes, returns to the initial state then  (a) process is thermodynamically in equilibrium  (b) process is executed in closed system cycle  (c) its entropy will ... sum of heat and work transfer will be zero  (e) no work will be done by the system.

Last Answer : Answer : d

Compressed air coming out from a punctured football  (a) becomes hotter  (b) becomes cooler1  (c) remains at the same temperature  (d) may become hotter or cooler depend-ing upon the humidity of the surround¬ing air  (e) attains atmospheric temperature.

Description : Compressed air coming out from a punctured football  (a) becomes hotter  (b) becomes cooler1  (c) remains at the same temperature  (d) may become hotter or cooler depend-ing upon the humidity of the surround¬ing air  (e) attains atmospheric temperature.

Last Answer : (b) becomes cooler1

A heat exchange process in which the product of pressure and volume remains constant is known as  (a) heat exchange process  (b) throttling process  (c) isentropic process  (d) adiabatic process  (e) hyperbolic process.

Description : A heat exchange process in which the product of pressure and volume remains constant is known as  (a) heat exchange process  (b) throttling process  (c) isentropic process  (d) adiabatic process  (e) hyperbolic process.

Last Answer : Answer : e

According to which law, all perfect gases change in volume by l/273th of their original volume at 0°C for every 1°C change in temperature when pressure remains constant  (a) Joule’s law  (b) Boyle’s law  (c) Regnault’s law  (d) Gay-Lussac law  (e) Charles’ law.

Description : According to which law, all perfect gases change in volume by l/273th of their original volume at 0°C for every 1°C change in temperature when pressure remains constant  (a) Joule’s law  (b) Boyle’s law  (c) Regnault’s law  (d) Gay-Lussac law  (e) Charles’ law.

Last Answer : Answer : e

Which law states that the specific heat of a gas remains constant at all temperatures and pressures  (a) Charles’ Law  (b) Joule’s Law  (c) Regnault’s Law  (d) Boyle’s Law  (e) there is no such law.

Description : Which law states that the specific heat of a gas remains constant at all temperatures and pressures  (a) Charles’ Law  (b) Joule’s Law  (c) Regnault’s Law  (d) Boyle’s Law  (e) there is no such law.

Last Answer : Answer : c

Intensive property of a system is one whose value  (a) depends on the mass of the system, like volume  (b) does not depend on the mass of the system, like temperature, pressure, etc.  (c) is not dependent on the path followed but on the state  (d) is dependent on the path followed and not on the state  (e) remains constant.

Description : Intensive property of a system is one whose value  (a) depends on the mass of the system, like volume  (b) does not depend on the mass of the system, like temperature, pressure, etc.  (c) is not ... on the state  (d) is dependent on the path followed and not on the state  (e) remains constant.

Last Answer : Answer : b

According to Gay-Lussac law for a perfect gas, the absolute pressure of given mass varies directly as  (a) temperature  (b) absolute  (c) absolute temperature, if volume is kept constant (d) volume, if temperature is kept constant  (e) remains constant,if volume and temperature are kept constant.

Description : According to Gay-Lussac law for a perfect gas, the absolute pressure of given mass varies directly as  (a) temperature  (b) absolute  (c) absolute temperature, if volume is kept constant ... , if temperature is kept constant  (e) remains constant,if volume and temperature are kept constant.

Last Answer : Answer : c

Which of the following represents the perpetual motion of the first kind  (a) engine with 100% thermal efficiency  (b) a fully reversible engine  (c) transfer of heat energy from low temperature source to high temperature source  (d) a machine that continuously creates its own energy  (e) production of energy by temperature differential in sea water at different levels.

Description : Which of the following represents the perpetual motion of the first kind  (a) engine with 100% thermal efficiency  (b) a fully reversible engine  (c) transfer of heat energy from low ... its own energy  (e) production of energy by temperature differential in sea water at different levels.

Last Answer : Answer : d

Which of the following cycles has maximum efficiency  (a) Rankine  (b) Stirling  (c) Carnot  (d) Brayton  (e) Joule.

Description : Which of the following cycles has maximum efficiency  (a) Rankine  (b) Stirling  (c) Carnot  (d) Brayton  (e) Joule.

Last Answer : Answer : c

The efficiency of a Carnot engine depends on  (a) working substance  (b) design of engine  (c) size of engine  (d) type of fuel fired  (e) temperatures of source and sink.

Description : The efficiency of a Carnot engine depends on  (a) working substance  (b) design of engine  (c) size of engine  (d) type of fuel fired  (e) temperatures of source and sink.

Last Answer : Answer : e

In the first law of thermodynamics, the total energy of the system remains constant.  A. True  B. False

Description : In the first law of thermodynamics, the total energy of the system remains constant.  A. True  B. False

Last Answer : Answer: A

According to first law of thermodynamics  (a) work done by a system is equal to heat transferred by the system  (b) total internal energy of a system during a process remains constant  (c) internal energy, enthalpy and entropy during a process remain constant  (d) total energy of a system remains constant

Description : According to first law of thermodynamics  (a) work done by a system is equal to heat transferred by the system  (b) total internal energy of a system during a process remains constant  ( ... , enthalpy and entropy during a process remain constant  (d) total energy of a system remains constant

Last Answer : Answer : d

It is a process during which the pressure remains constant  a. Adiabatic  b. Isentropic  c. Isobaric  d. Isotropic

Description : It is a process during which the pressure remains constant  a. Adiabatic  b. Isentropic  c. Isobaric  d. Isotropic

Last Answer : Isobaric

Which of the following occurs in a reversible polytrophic process?  a. Enthalpy remains constant  b. Internal energy does not change  c. Some heat transfer occurs  d. Entropy remains constant

Description : Which of the following occurs in a reversible polytrophic process?  a. Enthalpy remains constant  b. Internal energy does not change  c. Some heat transfer occurs  d. Entropy remains constant

Last Answer : Some heat transfer occurs

What happens to the internal energy of water at reference temperature where enthalpy is zero?  a. Becomes negative  b. Becomes positive  c. Remains constant  d. Cannot be defined

Description : What happens to the internal energy of water at reference temperature where enthalpy is zero?  a. Becomes negative  b. Becomes positive  c. Remains constant  d. Cannot be defined

Last Answer : Becomes negative

Heat cannot be created, nor destroyed, but it can be changed from one form to another. The energy in the universe remains constant.  a. 1st Law of Energy Conservation  b. 2nd Law of Energy Conservation  c. 3rd Law of Energy Conservation  d. None of the above

Description : Heat cannot be created, nor destroyed, but it can be changed from one form to another. The energy in the universe remains constant.  a. 1st Law of Energy Conservation  b. 2nd Law of Energy Conservation  c. 3rd Law of Energy Conservation  d. None of the above

Last Answer : 1st Law of Energy Conservation