The hp available at the crank shaft which is measured by a suitable dynamo meter is called 1. IMEP 2. BHP 3. Both 1 and 2 4. none of these

The hp available at the crank shaft which is measured by a suitable dynamo meter is called 1. IMEP 2. BHP 3. Both 1 and 2 4. none of these
by

1 Answer

Answer :

<!-- [if !supportLists] -->1.   <!-- [endif] -->ans 2

 


by

Related questions

In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Description : In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Last Answer : e. 25.5 m/s

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

What is a crank shaft?

Description : What is a crank shaft?

Last Answer : http://en.wikipedia.org/wiki/Crank_shaft

how to clean crank shaft of a 2004 chevy malibu

Description : how to clean crank shaft of a 2004 chevy malibu

Last Answer : Need Answer

how to put a 400 chevy crank shaft into a 350 chevy engine

Description : how to put a 400 chevy crank shaft into a 350 chevy engine

Last Answer : Need Answer

State the function of the following parts in a heat engine: a) Crank shaft b) spark plug c) carburettord) kick starter e) inlet valve f) outlet valve

Description : State the function of the following parts in a heat engine: a) Crank shaft b) spark plug c) carburettord) kick starter e) inlet valve f) outlet valve

Last Answer : a) Crankshaft converts the linear movement of piston into circular motion. b) Spark plug is used in petrol engine to ignite the mixture of petrol and air in the cylinder. c) Carburettorhelps to mix ... -air or air into the cylinder. f) Outlet Valve allows the exhaust gases out of the cylinder.

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

State the function of the following components. (i) Cam Shaft (ii) Crank Shaft

Description : State the function of the following components. (i) Cam Shaft (ii) Crank Shaft

Last Answer : Camshaft: The camshaft is a mechanical component of an internal combustion Engine. It opens and closes the inlet and exhaust valves of the engine at the right time, with the exact ... translate the linear reciprocating motion of a pistons into the rotational motion required by the automobile.

State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Description : State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Last Answer : Engine components Material Functions Piston Cat aluminum alloy To transmit the force of explosion to the crankshaft. To form seal so that the high pressure gases in ... atmosphere through the exhaust pipe after combustion stroke is completed. To keep back pressure minimum.

Describe forging sequence for crank shaft.

Description : Describe forging sequence for crank shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging.   [2] After preliminary roll forging, stock ... the finished part is then trimmed in blanking die to remove excess metal or flash.   

Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Description : Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging. [2] After preliminary roll forging, ... Then the finished part is then trimmed in blanking die to remove excess metal or flash.   

How many HP for tractor is suitable suitable for 20 hectares farm? A. 10-15 C. 20-25. B. 30-35 D. 40-45

Description : How many HP for tractor is suitable suitable for 20 hectares farm? A. 10-15 C. 20-25. B. 30-35 D. 40-45

Last Answer : 20-25

Identify the instrument that does not exist (A) Dynamo-meter type ammeter (B) Dynamo-meter type

Description : Identify the instrument that does not exist (A) Dynamo-meter type ammeter (B) Dynamo-meter type wattmeter (C) Moving-iron voltmeter (D) Moving-iron wattmeter

Last Answer : Identify the instrument that does not exist (A) Dynamo-meter type ammeter (B) Dynamo-meter type wattmeter (C) Moving-iron voltmeter (D) Moving-iron wattmeter

In a dynamo-meter type of moving coil instrument a swamping resistance is provided in order to:

Last Answer : In a dynamo-meter type of moving coil instrument a swamping resistance is provided inorder to: Provide equal time constant for moving coil and fixed coil, when used for ac measurement

The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero

Description : The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero

Last Answer : e. Zero

It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above

Description : It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above

Last Answer : Ans-                                     b. Pitman

The draft of a trailed type implement can be measured using a) Brake dynamometer b) Torque meter c) Tension dynamometer d) Dial gauge

Description : The draft of a trailed type implement can be measured using a) Brake dynamometer b) Torque meter c) Tension dynamometer d) Dial gauge Ans. c

Last Answer : Ans. c

26. Air velocity in ducts can be measured by using and manometer a) Orifice meter b) Borden gauge c) Pitot tube d) Anemometer

Description : Air velocity in ducts can be measured by using and manometer a) Orifice meter b) Borden gauge c) Pitot tube d) Anemometer

Last Answer : Pitot tube

Entropy is measured in ______.  A. Joule/Kelvin  B. Joule-Meter/Kelvin  C. Meter/Kelvin  D. Newton/Kelvin

Description : Entropy is measured in ______.  A. Joule/Kelvin  B. Joule-Meter/Kelvin  C. Meter/Kelvin  D. Newton/Kelvin

Last Answer : Joule/Kelvin

Unit power available for crop production is about 0.54hp/ha whereas desirable level is about ……. b. 2hp/ha c. 3hp/ha d. 2.5 hp/ha

Description : Unit power available for crop production is about 0.54hp/ha whereas desirable level is about ……. b. 2hp/ha c. 3hp/ha d. 2.5 hp/ha

Last Answer : Ans- a. 1hp/ha

Unit power is available for crop production is about ….hp/ha a. .54. c) .78 b. .89. d) .9

Description : Unit power is available for crop production is about ….hp/ha a. .54. c) .78 b. .89. d) .9

Last Answer : 54

The battery has following three major functions to perform: a) To provide a source of current for engine starting, lighting and use of horn. b) To help control the voltage in the electrical system. c) To store the current produced by dynamo/alternator and to furnish the current d) all of the above. Ans. d

Description : The battery has following three major functions to perform: a) To provide a source of current for engine starting, lighting and use of horn. b) To help control the voltage in the electrical system. c ... the current produced by dynamo/alternator and to furnish the current d) all of the above. Ans. d

Last Answer : ans d

A turbo chargers are driven by 1. Engine 2. Exhaust gas 3. Dynamo 4. PTO ans 2

Description : A turbo chargers are driven by 1. Engine 2. Exhaust gas 3. Dynamo 4. PTO ans 2

Last Answer : ans 2

A 5 BHP engine running at full load would consume diesel of the order of A. 0.3 kg/hr B. 1 kg/hr C. 3 kg/hr D. 5 kg/hr

Description : A 5 BHP engine running at full load would consume diesel of the order of A. 0.3 kg/hr B. 1 kg/hr C. 3 kg/hr D. 5 kg/hr

Last Answer : ANSWER ; B

Specific fuel consumption is defined as a. fuel consumption per hour b. fuel consumed per km. c. fuel consumed per BHP d. fuel consumed per hour per BHP

Description : Specific fuel consumption is defined as a. fuel consumption per hour b. fuel consumed per km. c. fuel consumed per BHP d. fuel consumed per hour per BHP

Last Answer : ANSWER d. fuel consumed per hour per BHP

The specific fuel consumption per BHP hour for petrol engine is approximately a. 0.1 kg b. 0.2 kg c. 0.25 kg d. 0.35 kg

Description : The specific fuel consumption per BHP hour for petrol engine is approximately a. 0.1 kg b. 0.2 kg c. 0.25 kg d. 0.35 kg

Last Answer : ANSWER c. 0.25 kg

The specific fuel consumption per BHP hour for diesel engine is approximately a. 0.1 kg b. 0.2 kg c. 0.3 kg d. 0.4 kg

Description : The specific fuel consumption per BHP hour for diesel engine is approximately a. 0.1 kg b. 0.2 kg c. 0.3 kg d. 0.4 kg

Last Answer : ANSWER b. 0.2 kg

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

What is BHP, How do you calculate the BHP of pump BHP-> Brake horse power?

Description : What is BHP, How do you calculate the BHP of pump BHP-> Brake horse power?

Last Answer : Ans The following formula is used for calculating the BHP capacity of the pump. Q H/4500 = in horse power i.e., P = Discharge in Liters/minute H= Head in Meters

What condition produces the 10-kHz error signal generated by the metering bridge in the HP- 431C power meter?

Description : What condition produces the 10-kHz error signal generated by the metering bridge in the HP- 431C power meter?

Last Answer : An unbalance in the metering bridge.

Why engine power is measured in horsepower (HP) ?

Description : Why engine power is measured in horsepower (HP) ?

Last Answer : James Watt compared engine output with that of work done by a horse. WD by horse = 746W.

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

Standard length of shaft is a ....... A. 5 meter B. 6 meter C. 7 meter D. All of these

Description : Standard length of shaft is a ....... A. 5 meter B. 6 meter C. 7 meter D. All of these

Last Answer : D. All of these

Answer the following S. No Statement Chose the correct answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the blanks 3 Non Contact Infrared Thermometer cannot measure temperature of objects placed in hazardous places True/False 4 To measure the RPM of a Flywheel, ______ type of RPM meter is used and for a visible shaft-end _______ type of RPM meter is used. Fill in the blanks 5 In a switch yard, _____ instrument is used to identify the loose joints and terminations Fill in the blanks 6 Every Designated Consumer shall have its first energy audit conducted by ________ Energy Auditor within ______ months of

Description :  Answer the following S. No Statement Chose the correct  answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the ... of RPM  meter is used and for a visible shaft-end _______ type of  RPM meter is used.

Last Answer : Sr  No Statement Chose the correct  answer OR Fill-in-the-blanks Solution 1 Fyrite measures CO2, O2 and  SO2 True/False False 2 Ultrasonic Flow Meter uses the  principle of____& ____ ... ]  10 In a gasification system the  reduction zone is above the  combustion zone True/False False

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

Which of the following is a data interfacing format? a.HP/GL b.ACER c.ASUS d.IBM

Description : Which of the following is a data interfacing format? a.HP/GL b.ACER c.ASUS d.IBM

Last Answer : a.HP/GL

One hp is equal to 1. 246watts 2. 250 watts 3. 746watts 4. 1000watts

Description : One hp is equal to 1. 246watts 2. 250 watts 3. 746watts 4. 1000watts

Last Answer : ans 3  

A potato digger elevator can be mounted to a tractor with hp. a) 10-15 hp b) 20-25 hp c) 50-70 hp d) None of the above

Description : A potato digger elevator can be mounted to a tractor with hp. a) 10-15 hp b) 20-25 hp c) 50-70 hp d) None of the above

Last Answer : 20-25 hp

Motorized knapsack sprayer are powered by - HP petrol engine. a) 1.2 to 3.2 b) 2.2 to 3.4 c) 0.2 to 3.2 d) 1.2 to 3.0

Description : Motorized knapsack sprayer are powered by - HP petrol engine. a) 1.2 to 3.2 b) 2.2 to 3.4 c) 0.2 to 3.2 d) 1.2 to 3.0

Last Answer : 1.2 to 3.0

The power developed in prime mover of power operated sprayer is a) 1 to 5 HP b) 5 to 10 HP c) 10 to 20 HP d) None of the above

Description : The power developed in prime mover of power operated sprayer is a) 1 to 5 HP b) 5 to 10 HP c) 10 to 20 HP d) None of the above

Last Answer : 1 to 5 HP

The hp required to operate subsoil plough a) 10-20hp b) 20-30hp c) 60-100hp d) 140-200hp

Description : The hp required to operate subsoil plough a) 10-20hp b) 20-30hp c) 60-100hp d) 140-200hp

Last Answer :  60-100hp

models of tractor are being produce in India in different HP ranges. A) 39 B) 40 C) 50 D) 45

Description : models of tractor are being produce in India in different HP ranges. A) 39 B) 40 C) 50 D) 45

Last Answer :  39

Calculate the power output in horsepower of an 80-kg man that climbs a flight of stairs 3.8 m high in 4.0 s.  a) 744.8 hp  b) 0.998 hp  c) 746 hp  d) 1.998 hp Formula: Power = Fd/t = mgh/t F = W = mg d = h

Description : Calculate the power output in horsepower of an 80-kg man that climbs a flight of stairs 3.8 m high in 4.0 s.  a) 744.8 hp  b) 0.998 hp  c) 746 hp  d) 1.998 hp Formula: Power = Fd/t = mgh/t F = W = mg d = h

Last Answer : 0.998 hp

3 horsepower (hp) = _____________watts?  a) 1492 watts  b) 2238 watts  c) 746 watts  d) 2238 kilowatts Formula: 1hp= 746 watts

Description : 3 horsepower (hp) = _____________watts?  a) 1492 watts  b) 2238 watts  c) 746 watts  d) 2238 kilowatts Formula: 1hp= 746 watts

Last Answer : 2238 watts

What horse power is required to isothermally compress 800 ft^3 of Air per minute from 14.7 psia to 120 psia?  A. 28 hp  B.108 hp  C.256 hp  D.13900 hp Formula: W= p1V1 ln (p1/p2) Power = dW / dt

Description : What horse power is required to isothermally compress 800 ft^3 of Air per minute from 14.7 psia to 120 psia?  A. 28 hp  B.108 hp  C.256 hp  D.13900 hp Formula: W= p1V1 ln (p1/p2) Power = dW / dt

Last Answer : 108 hp

The flanked tube mounted on the gang bold between every two disc to prevent the lateral movement of the disc on the shaft is called............ a. Bearing. c. Gang bolt b. Gang. d. Spool

Description : The flanked tube mounted on the gang bold between every two disc to prevent the lateral movement of the disc on the shaft is called............ a. Bearing. c. Gang bolt b. Gang. d. Spool

Last Answer : Spool

Each set of disk that are mounted on the common shaft is called the………… a. Gang control lever c. Spool b. Gang bolt. d. Gang

Description : Each set of disk that are mounted on the common shaft is called the………… a. Gang control lever c. Spool b. Gang bolt. d. Gang

Last Answer : Gang

Each set of discs that are mounted on a common shaft is called as i. Spool. c) Bearing ii. Gang. d) Gang control

Description : Each set of discs that are mounted on a common shaft is called as i. Spool. c) Bearing ii. Gang. d) Gang control

Last Answer : Gang

The lateral movement of disc on shaft is called as A) Spool. C) Gang B) Bearing D) Gear

Description : The lateral movement of disc on shaft is called as A) Spool. C) Gang B) Bearing D) Gear

Last Answer : Spool