It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above

It is the link between the knife and crank wheel of the mower. a. connecting rod c. rod d. None of above
by

1 Answer

Answer :

Ans-                                     b. Pitman


by

Related questions

In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Description : In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Last Answer : e. 25.5 m/s

The energy of expanding gas is transferred by piston to connecting rod through a. Crank pin b. Gudgeon pin c. Bearing d. Crankcase (Ans:b)

Description : The energy of expanding gas is transferred by piston to connecting rod through a. Crank pin b. Gudgeon pin c. Bearing d. Crankcase (Ans:b)

Last Answer : Which of the following is not used in four stroke compression-ignition (CI) engines? a. Fuel pump b. Spark plug c. Fuel injector d. Inlet and outlet Valves (Ans:b)

State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Description : State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Last Answer : Engine components Material Functions Piston Cat aluminum alloy To transmit the force of explosion to the crankshaft. To form seal so that the high pressure gases in ... atmosphere through the exhaust pipe after combustion stroke is completed. To keep back pressure minimum.

A mower knife is said to be in proper registration when the knife section stops in the ……………..of its guard ( fingers ) on every stroke a. offset c. inclined d. None of above

Description : A mower knife is said to be in proper registration when the knife section stops in the ……………..of its guard ( fingers ) on every stroke a. offset c. inclined d. None of above

Last Answer : <!-- [if !supportLists] -->a.  <!-- [endif] -->Ans-                     b. centre  

It is a mower with a knife made of several serrated triangular sections that reciprocate against stationary fingers. a. Rotary mower c. Cylinder mower. d. None of above

Description : It is a mower with a knife made of several serrated triangular sections that reciprocate against stationary fingers. a. Rotary mower c. Cylinder mower. d. None of above

Last Answer : Ans-   b. Reciprocating mower  

Crank speed on the mower with dynamically balanced systems a)850-1000rpm. b)1000-1200rpm c)850-1150rpm. d)1200-1600rpm

Description : Crank speed on the mower with dynamically balanced systems a)850-1000rpm. b)1000-1200rpm c)850-1150rpm. d)1200-1600rpm

Last Answer : b)1000-1200rpm

The tie rod connects the front wheel spindle arms and is actuated by the steering shaft through a) chain link b) gear link c) tension link d) drag link

Description : The tie rod connects the front wheel spindle arms and is actuated by the steering shaft through a) chain link b) gear link c) tension link d) drag link

Last Answer : d) drag link

are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Description : are the labelling of cutter bar. a) Shoe, ledger plate, wearing plate, knife, knife section, etc. b) Star wheel, engine, cage wheel, etc. c) both A & B d) Conveyor belt, cutter bar, rivers, etc

Last Answer : Shoe, ledger plate, wearing plate, knife, knife section, etc.

type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate

Description : type of connecting rod which is pinned to the crankshaft with the help of a pin, which helps to transmit the cut material. a) Pitman b) Cutter bat c) Shoe d) Wearing plate

Last Answer : Pitman 

267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Description : 267 .Double knives movers offers advantage over conventional mower are a)Double knife are dynamically balanced b) They can be operated at higher forward speeds then conventional mower c)They produce more uniform stubble height d)All of the above

Last Answer : d)All of the above

The components of disc plough are . a) Frame extension b) Top link connection c) Furrow wheel d) All of the above

Description : The components of disc plough are . a) Frame extension b) Top link connection c) Furrow wheel d) All of the above

Last Answer :    <!-- [endif] -->All of the above

How do I sharpen my kitchen knife using that steel rod thing that came with the set?

Description : How do I sharpen my kitchen knife using that steel rod thing that came with the set?

Last Answer : This might help you.

The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero

Description : The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero

Last Answer : e. Zero

The hp available at the crank shaft which is measured by a suitable dynamo meter is called 1. IMEP 2. BHP 3. Both 1 and 2 4. none of these

Description : The hp available at the crank shaft which is measured by a suitable dynamo meter is called 1. IMEP 2. BHP 3. Both 1 and 2 4. none of these

Last Answer : <!-- [if !supportLists] -->1.   <!-- [endif] -->ans 2  

What way do the rod bearing caps go onto the connecting rod on a Chevy 350 motor?

Description : What way do the rod bearing caps go onto the connecting rod on a Chevy 350 motor?

Last Answer : The notches for the bearings to lock from spinning are both onthe same side.

What are John deere 2010 connecting rod torque specs?

Description : What are John deere 2010 connecting rod torque specs?

Last Answer : Need answer

Addition of 2% nickel in steel makes it suitable for making (A) Electronic valves (B) Boiler plates, rivets etc. (C) Turbine blades (D) Connecting rod

Description : Addition of 2% nickel in steel makes it suitable for making (A) Electronic valves (B) Boiler plates, rivets etc. (C) Turbine blades (D) Connecting rod

Last Answer : (B) Boiler plates, rivets etc.

Maximum rod connecting limit by using knuckle joint is . A. 2 B. 3 C. 4 D. 5

Description : Maximum rod connecting limit by using knuckle joint is . A. 2 B. 3 C. 4 D. 5

Last Answer : B. 3

The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Description : The connecting rod bolts are tightened up so that the initial tightening stress (A) Approaches yield point (B) Approaches endurance limit (C) Approaches (yield point stress/factor of safety) (D) Approaches (endurance limit stress/factor of safety)

Last Answer : (A) Approaches yield point

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

Connecting rod of two stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Description : Connecting rod of two stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Last Answer : A. Compressive load

Connecting rod of four stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Description : Connecting rod of four stroke engine is subjected to A. Compressive load B. Tensile load C. Both compressive and tensile load D. None of the above

Last Answer : C. Both compressive and tensile load

Connecting rod generally have A)t-shape b)angle shape C)i-shape d)flst-shape

Description : Connecting rod generally have A)t-shape b)angle shape C)i-shape d)flst-shape

Last Answer : C)i-shape

Show the following components in an engine with neat sketch: piston, connecting rod, valves, spark plug

Description : Show the following components in an engine with neat sketch: piston, connecting rod, valves, spark plug

Last Answer : OR

Apply proper heat treatment process for manufacturing connecting rod of an engine.

Description : Apply proper heat treatment process for manufacturing connecting rod of an engine. 

Last Answer : Answer: The connecting rod may either be cast or forged when created and may also include allowable secondary alloy elements.  The normalizing step includes heating a rough connecting rod to ... , not throughout the entire rod, but instead only where high hardness is required functionally.

Identify the properties of material used for connecting rod with justification

Description : Identify the properties of material used for connecting rod with justification

Last Answer : Answer:  1. There are some materials that are commonly used in connecting rods such as alloys of steel, aluminum and titanium. Mostly connecting rods are made by forged steel. It is widely use ... times lighter than carbon steel. It is because density of Al360 is very less compared to carbon steel 

State functions and name suitable materials for connecting rod. Select suitable crosssection for connecting rod with justification

Description : State functions and name suitable materials for connecting rod. Select suitable crosssection for connecting rod with justification

Last Answer : Functions of connecting rod: A connecting rod, also called a con rod, is the part of a piston engine which connects the piston to the crankshaft. Together with the crank, the connecting rod ... a connecting rod may have rectangular section. For slow speed engines, circular sections may be used.

List basic design requirement of connecting rod.

Description : List basic design requirement of connecting rod.

Last Answer : In designing a connecting rod for I.C. engine, the following points should be taken into consideration : Strength to withstand the high inertia forces. Minimum mass to minimise ... undue wear. High speed reciprocation without noise. Rigid construction to withstand mechanical distortion.

It is a machine to separate grains from the harvested crop and provide clean grain without much loss and damage. a. Weeder c. mower d. None of above

Description : It is a machine to separate grains from the harvested crop and provide clean grain without much loss and damage. a. Weeder c. mower d. None of above

Last Answer : Ans-                              b. thresher  

Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Description : Flail mower is a mower with high speed swinging knives, operating in a. horizontal plane c. Vertical plane d. None of above

Last Answer : Ans-   b. either in the horizontal plane or in the vertical plane  

Cylinder mower has rotating blades arranged in cylindrical form. a. Straight c. inclined. d. None of above

Description : Cylinder mower has rotating blades arranged in cylindrical form. a. Straight c. inclined. d. None of above

Last Answer : Ans-                     b. helical  

The conventional type of Mower consists of which of the following a) Wearing Plate b) Nozzle c) Air Chamber d) None of the above

Description : The conventional type of Mower consists of which of the following a) Wearing Plate b) Nozzle c) Air Chamber d) None of the above

Last Answer : Wearing Plate

is a common troubles in the operation of Mower. a) Knives get twisted. b) Knives get melted. c) Knives gets rusted. d) Knives gets break

Description : is a common troubles in the operation of Mower. a) Knives get twisted. b) Knives get melted. c) Knives gets rusted. d) Knives gets break

Last Answer : Knives gets break

is a machine to cut herbage crops and leave the them in swath. a) Wind rower b) Sickle mower c) Fail mower d) Gang mower

Description : is a machine to cut herbage crops and leave the them in swath. a) Wind rower b) Sickle mower c) Fail mower d) Gang mower

Last Answer : Sickle mower

What might the outcome of the University of California, Merced, assault been if the attacker had had access to a gun rather than a knife? [Link]?

Description : What might the outcome of the University of California, Merced, assault been if the attacker had had access to a gun rather than a knife? [Link]?

Last Answer : answer:A person could say that this outcome was a triumph of gun control; there would be several dead people if a gun had been used, but instead we have four living people with knife wounds. So if ... it and construe it in some self-serving justification. Facts don't matter, if you're a gun nut,

There's a knife that is being offered on the Internet as able to pass through (edit) a metal detector. Is this possible? Please see the link.

Description : There's a knife that is being offered on the Internet as able to pass through (edit) a metal detector. Is this possible? Please see the link.

Last Answer : It may not get picked up by the metal detectors, but it will certainly send up a red flag when it goes through xray, which will see the outline of a knife. No way thats getting on a plane.

Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Description : Alignment of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. b

Last Answer : ans b

Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Description : Registration of cutter bar is a) Aligning centers of guard and knife b) Keeping cutter bur in 88 degrees c) Both d) None of these Ans. a

Last Answer : ans a

cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Description : cutter bar knife a) triangular shape b) square shape c) trapezoidal shape d) curved shape Ans. c

Last Answer : ans c

Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Description : Registration of a cutter bar means a) Centre of knife must stop in the centre of guard on each stroke b) Centre of knife should be ahead of guard c) Centre of knife should be behind the guard d) Centre of knife should be at the end of the guard

Last Answer : ans a

is also called as knife harrow. a. Spring tooth harrow c. Fixed tooth harrow d. None of the above

Description : is also called as knife harrow. a. Spring tooth harrow c. Fixed tooth harrow d. None of the above

Last Answer : Ans - b.Acme tooth harrow

is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board

Description : is part of the Cutter bar is shaped in Triangular shape with two cutting edges a) Knife head b) Knife back c) Grass board d) Knife Section

Last Answer :   <!-- [endif] -->Knife Section

is not well register, there is unbalance load, uneven harvesting and exclusive clogging of crops on the knife A) Vertical conveyor reaper B) MOVER C) Reaper binder D) Potato digger elevator.

Description : is not well register, there is unbalance load, uneven harvesting and exclusive clogging of crops on the knife A) Vertical conveyor reaper B) MOVER C) Reaper binder D) Potato digger elevator.

Last Answer : MOVER

Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Last Answer : Breaking of knives.

Knife clips are placed with wearing plates spaced from cm apart. A) 10-20cm B) 60-90cm C) 15-25cm D) 20-30cm

Description : Knife clips are placed with wearing plates spaced from cm apart. A) 10-20cm B) 60-90cm C) 15-25cm D) 20-30cm

Last Answer :  20-30cm

Knife clips are placed with wearing plates spaced to apart a) 20 to 30 b) 45 to 60 c) 20 to 35 d) 30 to 40

Description : Knife clips are placed with wearing plates spaced to apart a) 20 to 30 b) 45 to 60 c) 20 to 35 d) 30 to 40

Last Answer : 20 to 30

is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe

Description : is an assembly comparing of fingers, knife guides on wearing plates and shoe. a) Cutter bar b) Knife section c) Pitman d) Shoe

Last Answer : Cutter bar

In a torsion pendulum a.The body attached to the lower end of wire or rod must be elastic b.The clamp must be elastic c.The clamp must be elastic d.(A) and (B) above e.(A), (B) and (C) together

Description : In a torsion pendulum a.The body attached to the lower end of wire or rod must be elastic b.The clamp must be elastic c.The clamp must be elastic d.(A) and (B) above e.(A), (B) and (C) together

Last Answer : c. The clamp must be elastic

What is the connecting link between Annelida and Mollusca? -Do You Know?

Description : What is the connecting link between Annelida and Mollusca? -Do You Know?

Last Answer : answer:

Neopilina is a connecting link between

Description : Neopilina is a connecting link between

Last Answer : Neopilina is a connecting link between A. Arthropoda and Mollusca B. Annelida and mollusca C. Mollusca and Echinodermata D. Mollusca and Helminthes