State the function of the following parts in a heat engine: a) Crank shaft b) spark plug c) carburettord) kick starter e) inlet valve f) outlet valve

State the function of the following parts in a heat engine:

a) Crank shaft b) spark plug c) carburettord) kick starter e) inlet valve f) outlet valve
by

1 Answer

Answer :

a) Crankshaft converts the linear movement of piston into circular motion.

b) Spark plug is used in petrol engine to ignite the mixture of petrol and air in the cylinder.

c) Carburettorhelps to mix petrol vapours and air in proper proportion.

d) Kick starter is used to provide the initial kinetic energy needed to start the engine.

e) Inlet valve allows the mixture of petrol-air or air into the cylinder.

f) Outlet Valve allows the exhaust gases out of the cylinder.
by

Related questions

Why is an electrical outlet called an outlet when you plug things into it? Shouldn't it be called an inlet?

Description : Why is an electrical outlet called an outlet when you plug things into it? Shouldn't it be called an inlet?

Last Answer : Current flow out from the wall socket when you plug a cord into it. If you want this to be called an inlet and not an outlet, then it would need to be reversed. When you plugged the cord ... flow is by a conductor such as your plug that trips the circuit and allows the electricity to flow freely.

In centrifugal pump installation, (A) Pump is properly primed before starting (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe (C) The motor may burn out if it is started with empty delivery pipe and with open gate valve (D) All the above

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Description : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

Last Answer : Engine power output is a function of A. Crank shaft torque B. Speed C. Both (A) and (B) D. None of the above

State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Description : State the functions and materials of following engine components: (i) Piston (ii) Connecting rod (iii)Crank shaft (iv)Exhaust manifold

Last Answer : Engine components Material Functions Piston Cat aluminum alloy To transmit the force of explosion to the crankshaft. To form seal so that the high pressure gases in ... atmosphere through the exhaust pipe after combustion stroke is completed. To keep back pressure minimum.

how to put a 400 chevy crank shaft into a 350 chevy engine

Description : how to put a 400 chevy crank shaft into a 350 chevy engine

Last Answer : Need Answer

Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ............................Combined radial and axial loads Which of these pairs is/are correctly matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3

Last Answer : (b) 1 and 2

In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 (C) Equal to the difference between hot and cold fluids inlet temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Description : In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 ... temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Last Answer : (B) 0

Which one of the following is true to estimate the range of cooling tower? a) Range = cooling water inlet temperature – wet bulb temperature b) Range = cooling water outlet temperature – wet bulb temperature c) Range = heat load in kcal per hour / water circulation in lines per hour d) None of the above

Description : Which one of the following is true to estimate the range of cooling tower? a) Range = cooling water inlet temperature - wet bulb temperature b) Range = cooling water outlet temperature - wet bulb temperature ... = heat load in kcal per hour / water circulation in lines per hour d) None of the above

Last Answer : Range = heat load in kcal per hour / water circulation in lines per hour

ernal combustion engine that does not use spark plug is

Description : ernal combustion engine that does not use spark plug is

Last Answer : Diesel engine.

State the function of the following components. (i) Cam Shaft (ii) Crank Shaft

Description : State the function of the following components. (i) Cam Shaft (ii) Crank Shaft

Last Answer : Camshaft: The camshaft is a mechanical component of an internal combustion Engine. It opens and closes the inlet and exhaust valves of the engine at the right time, with the exact ... translate the linear reciprocating motion of a pistons into the rotational motion required by the automobile.

Why Joel's engine is unable to power his car the way it used to. The spark plug is working and the engine is compressing properly so what could be the problem?

Description : Why Joel's engine is unable to power his car the way it used to. The spark plug is working and the engine is compressing properly so what could be the problem?

Last Answer : Could be a fuel delivery problem such as a dirty fuelfilter.

Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Description : Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Last Answer : ANSWER a. fuel injector

A spark plug is used in a. petrol engine b. diesel engine c. gas engine d. steam engine

Description : A spark plug is used in a. petrol engine b. diesel engine c. gas engine d. steam engine

Last Answer : ANSWER a. petrol engine

Spark plug is provided in a/an (A) Engine having carburettor (B) Diesel engine (C) Compression ignition engine (D) Both (B) & (C)

Description : Spark plug is provided in a/an (A) Engine having carburettor (B) Diesel engine (C) Compression ignition engine (D) Both (B) & (C)

Last Answer : (A) Engine having carburettor

Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used? (A) Vapour locking (B) Hot starting (C) Spark plug fouling (D) All 'a', 'b' & 'c'

Description : Which of the following performance characteristics of a S.I engine is not affected by the front end volatility of the petrol used? (A) Vapour locking (B) Hot starting (C) Spark plug fouling (D) All 'a', 'b' & 'c'

Last Answer : (C) Spark plug fouling

Show the following components in an engine with neat sketch: piston, connecting rod, valves, spark plug

Description : Show the following components in an engine with neat sketch: piston, connecting rod, valves, spark plug

Last Answer : OR

The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Description : The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design

Last Answer : ANSWER : B

In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°

Description : In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°

Last Answer : ANSWER : A

Receptacle outlets aboard ship should be designed so those mounted according to 46 CFR 111 have _____________. A. there must be a sufficient number of receptacle outlets in the crew accommodations for an adequate level of habitability B. each receptacle outelt must be compatible with the voltage and current of the circuit in which it is installed C. a receptacle outlet must not have any exposed parts with the plug opening uncovered D. all of the above

Description : Receptacle outlets aboard ship should be designed so those mounted according to 46 CFR 111 have _____________. A. there must be a sufficient number of receptacle outlets in the crew accommodations for an ... outlet must not have any exposed parts with the plug opening uncovered D. all of the above

Last Answer : Answer: D

An endothermic second order reaction is carried out in an adiabatic plug flow reactor. The rate of heat generation is: (A) Maximum at the inlet of the reactor (B) Maximum at the exit of the reactor (C) Maximum at the centre of the reactor (D) Constant throughout the reactor

Description : An endothermic second order reaction is carried out in an adiabatic plug flow reactor. The rate of heat generation is: (A) Maximum at the inlet of the reactor (B) Maximum at the exit of the reactor (C) Maximum at the centre of the reactor (D) Constant throughout the reactor

Last Answer : (A) Maximum at the inlet of the reactor

The 'E' curve for a non-ideal reactor defines the fraction of fluid having age between t and t + dt (A) At the inlet (B) At the outlet (C) In the reactor (D) Averaged over the inlet and outlet

Description : The 'E' curve for a non-ideal reactor defines the fraction of fluid having age between t and t + dt (A) At the inlet (B) At the outlet (C) In the reactor (D) Averaged over the inlet and outlet

Last Answer : (B) At the outlet

In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature

Description : In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature

Last Answer : Ans :c

A tank has two inlet pipes, A and B, which can fill the tank in 12 hours and 18 hours respectively, and an outlet C which can empty the tank in 9 hour

Description : A tank has two inlet pipes, A and B, which can fill the tank in 12 hours and 18 hours respectively, and an outlet C which can empty the tank in 9 hour

Last Answer : A tank has two inlet pipes, A and B, which can fill the tank in 12 hours and 18 hours ... time taken right from the start to fill the tank.

Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept 5 to 7.5 cm below the inlet invert level C. The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Description : Which one of the following statements regarding septic tanks is wrong? A. A gap of 7.5 cm between the bottom of the covering slab and the top level of scum is provided B. The outlet invert level is kept ... . The minimum width of septic level is 90 cm D. The depth of tank is kept equal to its width

Last Answer : ANS: D

A solid material shows case hardening properties while drying. Which of the following should be controlled to control the drying process? (A) Flow rate of inlet air (B) Relative humidity of outlet air (C) Humidity of inlet air (D) Temperature of the solid

Description : A solid material shows case hardening properties while drying. Which of the following should be controlled to control the drying process? (A) Flow rate of inlet air (B) Relative humidity of outlet air (C) Humidity of inlet air (D) Temperature of the solid

Last Answer : (D) Temperature of the solid

6. In a forward feed multiple effect, the pressure build up will be (A) Least at the inlet of the first effect (B) Least at the outlet of the last effect (C) Highest at the inlet of the last effect (D) Highest at the outlet of the last effect

Description : 6. In a forward feed multiple effect, the pressure build up will be (A) Least at the inlet of the first effect (B) Least at the outlet of the last effect (C) Highest at the inlet of the last effect (D) Highest at the outlet of the last effect

Last Answer : (B) Least at the outlet of the last effect

Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Description : Cavitation in a centrifugal pump can be avoided by keeping the (A) Inlet pressure high (B) Outlet pressure low (C) Inlet pressure low (D) Outlet pressure high

Last Answer : (A) Inlet pressure high

Momentum correction factor used in fluid flow problems accounts for the (A) Change in direction of flow (B) Change in total energy (C) Change in pressure (D) Non uniform direction of velocities at inlet & outlet sections

Description : Momentum correction factor used in fluid flow problems accounts for the (A) Change in direction of flow (B) Change in total energy (C) Change in pressure (D) Non uniform direction of velocities at inlet & outlet sections

Last Answer : (D) Non uniform direction of velocities at inlet & outlet sections

The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip of a blade curves in a direction opposite to that (C) Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Description : The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip ... Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction

Last Answer : (D) Outlet tip of a blade is towards the direction

To avoid an interruption in the flow of a siphon, an air vessel is provided (A) At the inlet (B) At the outlet (C) At the summit (D) At any point between inlet and outle

Description : To avoid an interruption in the flow of a siphon, an air vessel is provided (A) At the inlet (B) At the outlet (C) At the summit (D) At any point between inlet and outle

Last Answer : Answer: Option C

Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Description : Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Last Answer : (b) Difference in pressure between suction and delivery ends

For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing guide vane angle at inlet as 90o c) Providing runner vane angle at exit as 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Description : For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing ... 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Last Answer : d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Faucet A basically used as inlet pipe and Faucet B is used as outlet pipe. Faucet A and B both are opened simultaneously, all the time. When Faucet A fills the tank and Faucet B empty the tank, it will take thrice the time than when both the pipes fill the tank. When Faucet B is used for filling the tank, its efficiency remains constant. What is the ratio of efficiency of Faucet A and Faucet B respectively? a) 1:2 b) 2:1 c) 1:3 d) 3:1

Description : Faucet A basically used as inlet pipe and Faucet B is used as outlet pipe. Faucet A and B both are opened simultaneously, all the time. When Faucet A fills the tank and Faucet B empty the tank, it will take thrice the ... efficiency of Faucet A and Faucet B respectively? a) 1:2 b) 2:1 c) 1:3 d) 3:1

Last Answer : B Efficiency when both pipes used to fill = A + B And efficiency when Faucet A is used to fill and Faucet B is used to empty the tank = A-B So (A+B)/(A-B)=3/1 A/B+1/(A/B-1)=3/1 A/B+1=3(A/B-1) 3A/B-A/B=4 2A/B=4 A/B=2 Thus, the ratio of efficiency of Faucet A and B =2:1

24 pumps are connected to a tank. Some of them are inlet pumps and the others are outlet pumps. Each of the inlet pumps an fill the tank in 16hours and each of the outlet pumps can empty the tank completely in 12hours. If all the pumps are kept open, the empty tank gets filled in 48 hours. How many inlet pumps are there? A) 16 B) 18 C) 17 D) 14

Description : 24 pumps are connected to a tank. Some of them are inlet pumps and the others are outlet pumps. Each of the inlet pumps an fill the tank in 16hours and each of the outlet pumps can empty the tank completely in ... gets filled in 48 hours. How many inlet pumps are there? A) 16 B) 18 C) 17 D) 14

Last Answer : D (x/16)-[(24-x)/12] = 1/48 x/16-24/48+x/12=1/48 (3+4)x/48=97/48 7x/48=97/48 7x=97 X=14

In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Description : In a slider crank mechanism, the crank is rotating at 200 rpm. If length of connecting rod is 8 mts and crank shaft is 2 mts, velocity of crosshead at 30? rotation of crank shaft equals. a.30.2 m/s b.33.2 m/s c.35.8 mts/s d.107 dynes e.25.5 m/s

Last Answer : e. 25.5 m/s

With neat labeled figure, explain the working of any two position of PCV (positive crank case ventilation) valve.

Description : With neat labeled figure, explain the working of any two position of PCV (positive crank case ventilation) valve.

Last Answer : PCV Valve: It consists of a spring loaded tapered valve for flow control. The crankcase pressure and manifold vacuum act together to close the valve where as the spring pressure tends to keep it open.(Fig a ... back seat sealing the inlet and crankcase is protected from the back fire.(Fig d).

What is a crank shaft?

Description : What is a crank shaft?

Last Answer : http://en.wikipedia.org/wiki/Crank_shaft

how to clean crank shaft of a 2004 chevy malibu

Description : how to clean crank shaft of a 2004 chevy malibu

Last Answer : Need Answer

The hp available at the crank shaft which is measured by a suitable dynamo meter is called 1. IMEP 2. BHP 3. Both 1 and 2 4. none of these

Description : The hp available at the crank shaft which is measured by a suitable dynamo meter is called 1. IMEP 2. BHP 3. Both 1 and 2 4. none of these

Last Answer : <!-- [if !supportLists] -->1.   <!-- [endif] -->ans 2  

Describe forging sequence for crank shaft.

Description : Describe forging sequence for crank shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging.   [2] After preliminary roll forging, stock ... the finished part is then trimmed in blanking die to remove excess metal or flash.   

Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Description : Draw simple labeled sketch showing forging sequence for manufacturing Crank Shaft.

Last Answer : Forging Sequence for Manufacturing Crank Shaft: [1] Stock is redistributed and size is increased at certain place and reduced at other place by roll forging. [2] After preliminary roll forging, ... Then the finished part is then trimmed in blanking die to remove excess metal or flash.   

State the functions following ignition system components (i) Ignition coil (ii) Distributor (iii)Condenser (iv)Spark plug

Description : State the functions following ignition system components (i) Ignition coil (ii) Distributor (iii)Condenser (iv)Spark plug

Last Answer : Functions following ignition system components: (i) Ignition coil: Ignition coil receives voltage from primary circuit and convert it to very high voltage up to 28000 volts required for spark by means of ... Charge of air and petrol is ignited by means of the spark produced by spark plug.

An endothermic aqueous phase first order irreversible reaction is carried out in an adiabatic plug flow reactor. The rate of reaction: (A) Is maximum at the inlet of the reactor (B) Goes through a maximum along the length of the reactor (C) Goes through a minimum along the length of the reactor (D) Is maximum at the exit of the reactor

Description : An endothermic aqueous phase first order irreversible reaction is carried out in an adiabatic plug flow reactor. The rate of reaction: (A) Is maximum at the inlet of the reactor (B) Goes through a maximum ... through a minimum along the length of the reactor (D) Is maximum at the exit of the reactor

Last Answer : (A) Is maximum at the inlet of the reactor

A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel cycle is higher than the Otto cycle, at a fixed compression ratio c. The compression ratio of a diesel engine is higher than that of an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Description : A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel ... an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Last Answer : ANSWER c. The compression ratio of a diesel engine is higher than that of an S.I engine

In diesel engine, the fuel is ignited by a. spark b. injected fuel c. heat resulting from compressing air that is supplied for combustion d. ignitor

Description : In diesel engine, the fuel is ignited by a. spark b. injected fuel c. heat resulting from compressing air that is supplied for combustion d. ignitor

Last Answer : ANSWER c. heat resulting from compressing air that is supplied for combustion

In a diesel engine the high temperature needed to ignite the fuel is achieved by – (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Description : In a diesel engine the high temperature needed to ignite the fuel is achieved by – (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Last Answer : (3) compressing air in the cylinders Explanation: Diesel engines use the heat of compressed air to ignite the fuel (intakes air, compresses it, then injects fuel). Diesel engines need high compression ratios to generate the high temperatures required for fuel auto ignition.

In a diesel engine the high temperature needed to ignite the fuel is achieved by (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Description : In a diesel engine the high temperature needed to ignite the fuel is achieved by (1) using heat from exhaust (2) the battery (3) compressing air in the cylinders (4) an electrical spark

Last Answer : compressing air in the cylinders

If you are beset by hordes of chiggers, and are itching like mad, would grabbing a live spark plug wire on a lawn mower kill the suckers?

Description : If you are beset by hordes of chiggers, and are itching like mad, would grabbing a live spark plug wire on a lawn mower kill the suckers?

Last Answer : WTF is a chigger?

Does a hotter spark on a spark plug mean that you will get better gas mileage?

Description : Does a hotter spark on a spark plug mean that you will get better gas mileage?

Last Answer : Need Answer

if you make the gap on the spark plug closer? Will that improve gas mileage?

Description : if you make the gap on the spark plug closer? Will that improve gas mileage?

Last Answer : Need Answer