Explain Briefly About Friction And Anti-friction Bearings?

Explain Briefly About Friction And Anti-friction Bearings?
by

1 Answer

Answer :

 Friction bearings. This type of bearings contact that shaft directly such as bush bearing ,journal bearing etc. These bearings generally made of cast iron ,brass and gun metal.
 Anti-friction bearings. These type of bearings have rolling elements such as balls, rollers etc.
by

Related questions

What Are The Reasons Of Over Heating On Anti-friction Bearings?

Description : What Are The Reasons Of Over Heating On Anti-friction Bearings?

Last Answer : The main reasons are, inadequate lubrication ,overloading ,miss-alignment and bearing in defective condition.

What Are The Advantages Of Anti-friction Bearing Over A Friction Bearing?

Description : What Are The Advantages Of Anti-friction Bearing Over A Friction Bearing?

Last Answer :  For reducing wear and tear.  For saving the power consumption.  For easy setup.  For smooth running of machine.  For running at slow and high speed carrying light and heavy loads.

Ball bearings are used in cycles, scooters etc. to _____. A. Reduce the friction between the wheel and the axle B. Increase the friction between the wheel and the axle C. Reduce the friction between ground and the wheel D. None of these

Description : Ball bearings are used in cycles, scooters etc. to _____. A. Reduce the friction between the wheel and the axle B. Increase the friction between the wheel and the axle C. Reduce the friction between ground and the wheel D. None of these

Last Answer : ANSWER: A

The function of ball bearings in a wheel is – (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Description : The function of ball bearings in a wheel is – (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Last Answer : (2) to convert kinetic friction into rolling friction Explanation: A ball bearing is a type of rollingelement bearing that uses balls to maintain the separation between the bearing races. The purpose of a ball bearing is to reduce rotational friction and support radial and axial loads.

The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the bearings C. strictly converted to heat generated by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Description : The reactive power drawn by a motor from an AC generator is the power which is _____________. A. used to establish the magnetic field of the motor B. lost in overcoming friction in the ... by current flow through the windings D. transmitted directly through the rotor shaft to perform useful work

Last Answer : Answer: A

Babbitt metal used for making bearings should have (A) High co-efficient of friction between journal and bearing (B) Ability to retain lubricant on its surface (C) Low co-efficient of friction between journal and bearing (D) Both (B) & (C)

Description : Babbitt metal used for making bearings should have (A) High co-efficient of friction between journal and bearing (B) Ability to retain lubricant on its surface (C) Low co-efficient of friction between journal and bearing (D) Both (B) & (C)

Last Answer : (A) High co-efficient of friction between journal and bearing

The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Description : The antifriction bearings (a) have low starting and low running friction at moderate speeds (b) have a high initial cost (c) can carry both radial and thrust loads (d) all the mentioned

Last Answer : (d) all the mentioned

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Description : The ball bearings are provided with a cage (a) to reduce friction (b) to facilitate slipping of balls (c) to prevent the lubricant from flowing out (d) to maintain the balls at a fixed distance apart

Last Answer : (d) to maintain the balls at a fixed distance apart

In a journal bearings, the radius of the friction circle increases with the increase in- [IES-1997] (a) Load (b) Radius of the journal (c) Speed of the journal (d) Viscosity of the lubricant

Description : In a journal bearings, the radius of the friction circle increases with the increase in- [IES-1997] (a) Load (b) Radius of the journal (c) Speed of the journal (d) Viscosity of the lubricant

Last Answer : (b) Radius of the journal

Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Description : Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed

Last Answer : d) All of the listed

The function of ball bearings in a wheel is : (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Description : The function of ball bearings in a wheel is : (1) to increase friction (2) to convert kinetic friction into rolling friction (3) to convert static friction into kinetic friction (4) just for convenience

Last Answer : to convert kinetic friction into rolling friction

The advantages of electrometric bearings are a) Permits movement of the structure in all directions b) Serves as a shock absorber due to anti-vibration properties of elestomeric c) better dispersion of longitudinal forces to the approaches d) All of the above*

Description : The advantages of electrometric bearings are a) Permits movement of the structure in all directions b) Serves as a shock absorber due to anti-vibration properties of elestomeric c) better dispersion of longitudinal forces to the approaches d) All of the above*

Last Answer : d) All of the above*

Explain Briefly The Uses Of Pipe Vice And Pipe Wrench ?

Description : Explain Briefly The Uses Of Pipe Vice And Pipe Wrench ?

Last Answer :  Pipe vice. It is used to hold the pipe firmly while cutting, threading etc.  Pipe wrench. It is used fir tightening and loosening the pipes.

Explain Briefly The Use Of Clutch?

Description : Explain Briefly The Use Of Clutch?

Last Answer : Clutch is used to connect and disconnect the driving and driven units of a machine. It does the function when machine speed is changed after stopping the driving unit.

What Are The Various Types Of Bearings?

Description : What Are The Various Types Of Bearings?

Last Answer :  Bush Bearing. It is a plain cylindrical bearing made of brass , gun metal ,cast iron etc. Its inner bore is finished and made running fit to the shaft. It is generally used on low speed ... is fixed in housing .Balls have point contact and are free in the races,friction makes balls to rotate.

Where Are The Following Bearings Used?

Description : Where Are The Following Bearings Used?

Last Answer :  Ball bearing is generally used on high speed with light load because it has point contact.  Roller bearing is generally used on high speed with heavy load because it has line contact.

Where Can I Find Product Specifications On Bearings And Other Products?

Description : Where Can I Find Product Specifications On Bearings And Other Products?

Last Answer : The best method for obtaining this information is to contact one of our experienced sales reps. we have extensive resources available to us. If the sales person cannot immediately answer your question, we will research it and respond in a timely manner.

Besides Storing Bearings On The Shelf, What’s The “correct” Way To Store Them?

Description : Besides Storing Bearings On The Shelf, What’s The “correct” Way To Store Them?

Last Answer : Keep bearings in a clean, dry location, and watch temperature changes as drastic changes can harm the bearing if any moisture is present. Handle bearings as little as possible, as your fingerprints can ... to store them by keeping the oldest at the front, and always using the oldest bearing first.

Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Description : Play in bearings and worn knife head holders caused due to in cutter bar. A) Pitman B) Breaking of knives. C) Knife head. D) Grass board.

Last Answer : Breaking of knives.

Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For hinged condition C. Deep groove ball bearing 3. For pure radial load D. Thrust ball bearing 4. For axial and radial load A B C D A B C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Description : Match List-I (Type of Anti-friction bearing) with List-II (Specific Use) and select the using the code given below the Lists: [IES-2006] List-I List -II A. Self-aligning ball bearing 1. For pure axial load B. Taper roller bearing 2. For ... C D (a) 2 1 3 4 (b) 3 4 2 1 (c) 2 4 3 1 (d) 3 1 2 4

Last Answer : (c) 2 4 3 1

The nature of loading at various locations and other surfaces conditions called a.friction b.traction c.boundary condition d.surfacing

Description : The nature of loading at various locations and other surfaces conditions called a.friction b.traction c.boundary condition d.surfacing

Last Answer : c.boundary condition

A particle inside a hollow sphere of internal radius r with coefficient of friction 1/?3 can rest upto height of a.0.18 r b.0.435 r c.0.25 r d.0.134 r e.0.125 r

Description : A particle inside a hollow sphere of internal radius r with coefficient of friction 1/?3 can rest upto height of a.0.18 r b.0.435 r c.0.25 r d.0.134 r e.0.125 r

Last Answer : d. 0.134 r

The slope on the road generally provided on the curves is known as a.Angle of repose b.Angle of friction c.Angle of banking d.Angle of reaction e.None of the above

Description : The slope on the road generally provided on the curves is known as a.Angle of repose b.Angle of friction c.Angle of banking d.Angle of reaction e.None of the above

Last Answer : c. Angle of banking

The angle of friction is a.The angle which frictional force makes with the normal b.The anle at which the force applied from external souce will cause movement c.The angle at which fictional force is inclined to external force d.The angle between the normal reaction and the resultant of normal reaction and the limiting friction e.None of the above

Description : The angle of friction is a.The angle which frictional force makes with the normal b.The anle at which the force applied from external souce will cause movement c.The angle at which fictional ... the normal reaction and the resultant of normal reaction and the limiting friction e.None of the above

Last Answer : d. The angle between the normal reaction and the resultant of normal reaction and the limiting friction

A uniform cylinder of weight W is rolling while slipping on a rough horizontal surface under the influence of a horizontal force. The force of friction between the cylinder and the surface is a.Proportional to the coefficient of static friction b.Proportional to the coefficient of dynamic friction c.Indeterminate d.Determinate but depends on the acceleration of the cylinder e.None of the above

Description : A uniform cylinder of weight W is rolling while slipping on a rough horizontal surface under the influence of a horizontal force. The force of friction between the cylinder and the surface is a. ... c.Indeterminate d.Determinate but depends on the acceleration of the cylinder e.None of the above

Last Answer : c. Indeterminate

A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of maximum compession of spring, neglecting friction to that while considering friction would be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Description : A block of weight 20 kg slides with an initial velocity of 2 m sec down an inclined plane on to a spring of stiffness 10 kg/cm. If the co--efficient of friction is 0.2, angle ? = 30 the ratio of ... be a.More than one b.One c.Less than one d.Depends on the stiffness of spring e.None of the above

Last Answer : a. More than one

The principle of conservation of energy cannot be applied in case of a.Flow of heat through a metal b.Ideal flow of water in a pipe c.Simple pendulum d.Sliding of a particle along inclined plane with friction e.A particle moving in gravitational field

Description : The principle of conservation of energy cannot be applied in case of a.Flow of heat through a metal b.Ideal flow of water in a pipe c.Simple pendulum d.Sliding of a particle along inclined plane with friction e.A particle moving in gravitational field

Last Answer : e. A particle moving in gravitational field

A car is travelling at 90 km/hour on a rough road where the coefficient of friction between the road and the tyre is 0.5. The distance the car will skid before stopping when the brakes are jammed suddenly would be a.127.4 m b.95.55 m c.63.7 m d.31.85 m e.90 m

Description : A car is travelling at 90 km/hour on a rough road where the coefficient of friction between the road and the tyre is 0.5. The distance the car will skid before stopping when the brakes are jammed suddenly would be a.127.4 m b.95.55 m c.63.7 m d.31.85 m e.90 m

Last Answer : c. 63.7 m

Ice is slippery when a man walks on it because a.Increase of pressure causes it to melt b.Ice is brittle c.There is no friction d.It is very chill e.Its surface is smooth

Description : Ice is slippery when a man walks on it because a.Increase of pressure causes it to melt b.Ice is brittle c.There is no friction d.It is very chill e.Its surface is smooth

Last Answer : a. Increase of pressure causes it to melt

The angle which an inclined surface makes with the horizontal when a body placed on it is on the point moving down is known as a.Angle of friction b.Angle of limiting friction c.Angle of inclination d.Angle of repose e.None of the above

Description : The angle which an inclined surface makes with the horizontal when a body placed on it is on the point moving down is known as a.Angle of friction b.Angle of limiting friction c.Angle of inclination d.Angle of repose e.None of the above

Last Answer : d. Angle of repose

The ideal angle of banking provided on roads a.Depends on (velocity)2 of vehicle b.Depends on the nature of road surface c.Depend on coefficient of friction between the road and the vehicle cantact point d.Depends on weight of the vehicle e.All above

Description : The ideal angle of banking provided on roads a.Depends on (velocity)2 of vehicle b.Depends on the nature of road surface c.Depend on coefficient of friction between the road and the vehicle cantact point d.Depends on weight of the vehicle e.All above

Last Answer : a. Depends on (velocity)2 of vehicle

Kinetic friction is a.Maximum value of frictional force when a body is about to move b.Friction between two well lubricated bodies c.Friction force acting when the body is in motion d.Driction force which keeps a body in motion e.None of the above

Description : Kinetic friction is a.Maximum value of frictional force when a body is about to move b.Friction between two well lubricated bodies c.Friction force acting when the body is in motion d.Driction force which keeps a body in motion e.None of the above

Last Answer : c. Friction force acting when the body is in motion

If the angle of friction is zero a body will experience a.Infinite friction b.Zero friction c.The force of friction will act normal to the plane d.The force of friction will act in the direction of motion e.None of the above

Description : If the angle of friction is zero a body will experience a.Infinite friction b.Zero friction c.The force of friction will act normal to the plane d.The force of friction will act in the direction of motion e.None of the above

Last Answer : b. Zero friction

Which one of the following is not the law of dry friction? a.If friction is neglected, the reactions are always normal to the surfaces on contact b.Friction always acts to oppose the relative motion of the free body c.If static friction is acting, the value of the friction force may vary from zero to its maximum value d.The force of friction is always normal to the surface e.All of the above

Description : Which one of the following is not the law of dry friction? a.If friction is neglected, the reactions are always normal to the surfaces on contact b.Friction always acts to oppose the relative motion of ... its maximum value d.The force of friction is always normal to the surface e.All of the above

Last Answer : d. The force of friction is always normal to the surface

A 5 m ladder of mass 25 kg is placed in a position where its inclination to a vertical wall is at 30?. A 100 kg man is to climb the ladder. If the coefficient of static friction is 0.25 the height along ladder at which the slipping will be induced would be a.2.4 m b.1.6 m c.0.8 m d.1.2 m e.0.5 m

Description : A 5 m ladder of mass 25 kg is placed in a position where its inclination to a vertical wall is at 30?. A 100 kg man is to climb the ladder. If the coefficient of static friction is 0.25 the height along ladder at which the slipping will be induced would be a.2.4 m b.1.6 m c.0.8 m d.1.2 m e.0.5 m

Last Answer : c. 0.8 m

A body of weight W is resting at a plane inclined at 30? to the horizontal. It is attached to a string making an angle of 60? with horizontal. If the angle of friction be 30? the tension in the string would be a.Zero b.W c.W/2 d.2W e.None of the above

Description : A body of weight W is resting at a plane inclined at 30? to the horizontal. It is attached to a string making an angle of 60? with horizontal. If the angle of friction be 30? the tension in the string would be a.Zero b.W c.W/2 d.2W e.None of the above

Last Answer : c. W/2

Coulomb friction is a.Friction between solids and liquids b.Friction between electrically charged bodies c.Friction between lubricated surface d.Friction between dry surfaces e.Friction between bodies having relative motion

Description : Coulomb friction is a.Friction between solids and liquids b.Friction between electrically charged bodies c.Friction between lubricated surface d.Friction between dry surfaces e.Friction between bodies having relative motion

Last Answer : d. Friction between dry surfaces

The maximum efficiency of a scres jack having square threads and friction angle of 30 degree will be a.0.2 b.0.11 c.0.05 d.0.33 e.0.09

Description : The maximum efficiency of a scres jack having square threads and friction angle of 30 degree will be a.0.2 b.0.11 c.0.05 d.0.33 e.0.09

Last Answer : d. 0.33

Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Description : Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Last Answer : b. 163.5 KW

A body of weight 100 kg is placed on a horizontal plane. A horizontal force of 30 kg is applied and the block is just on the point of motion. The angle of friction is a.About 16? b.30? c.45? d.60? e.None of the above

Description : A body of weight 100 kg is placed on a horizontal plane. A horizontal force of 30 kg is applied and the block is just on the point of motion. The angle of friction is a.About 16? b.30? c.45? d.60? e.None of the above

Last Answer : a. About 16?

A uniform cylinder of weight W is rolling while slipping on a rough horizontal surface under the influence of a horizontal force. The force of friction between the cylinder and the surface is a.Indeterminate b.Proportional to the coefficient of dynamic friction c.Determinate but depends on the acceleration of the cylinder d.107 dynes e.Proportional to the coefficient of static friction

Description : A uniform cylinder of weight W is rolling while slipping on a rough horizontal surface under the influence of a horizontal force. The force of friction between the cylinder and the surface is a. ... on the acceleration of the cylinder d.107 dynes e.Proportional to the coefficient of static friction

Last Answer : c. Determinate but depends on the acceleration of the cylinder

A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move down the plane to that when it move up the plane would be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Description : A particle moves along a rough plane inclined at 30? to the horizontal. The co-efficient of friction between the particle and the plane is 0.1. Its initial velocity is 15 m/sec. The ratio of the velocity of the particle when it move ... be in the regions a.8 ? 10 b.5 ? 7 c.2 ? 3 d.4 ? 6 e.10 ? 13

Last Answer : b. 5 ? 7

Which of the following bearing will have least coefficient of friction a.Single ball bearing b.Cylinderical roller bearing c.Self aligury bearing d.Thrust ball bearing e.Tapered bearing

Description : Which of the following bearing will have least coefficient of friction a.Single ball bearing b.Cylinderical roller bearing c.Self aligury bearing d.Thrust ball bearing e.Tapered bearing

Last Answer : e. Tapered bearing

Static friction is always a.greater than the dynamic driction b.either greater or more than the dynamic friction c.less than the dynamic friction d.107 dynes e.equal to the dynamic friction

Description : Static friction is always a.greater than the dynamic driction b.either greater or more than the dynamic friction c.less than the dynamic friction d.107 dynes e.equal to the dynamic friction

Last Answer : a. greater than the dynamic driction

The maximum frictional force which comes into play when a body just begins to slide over the surface of another body is known as a.Kinetic friction b.Rolling friction c.Dynamic friction d.Limiting friction e.Sliding friction

Description : The maximum frictional force which comes into play when a body just begins to slide over the surface of another body is known as a.Kinetic friction b.Rolling friction c.Dynamic friction d.Limiting friction e.Sliding friction

Last Answer : d. Limiting friction

The coefficient of friction is a.The tangent of the angle between the normal reaction and direction of limiting friction b.The tangent of the angle between the normal reaction and the resultant of the normal reaction and the limiting friction c.The tangent of the angle of the net resultant force with the direction of motion d.The tangent of the angle between the horizontal plane and the resultant force e.The angle between the normal reaction and the resultant of normal reaction and the limiting friction

Description : The coefficient of friction is a.The tangent of the angle between the normal reaction and direction of limiting friction b.The tangent of the angle between the normal reaction and the resultant ... e.The angle between the normal reaction and the resultant of normal reaction and the limiting friction

Last Answer : a. The tangent of the angle between the normal reaction and direction of limiting friction

A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the force exerted by the jet on the plate would be in the range a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Description : A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the ... a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Last Answer : a. 15 - 20 kg

The coefficient of static friction will have the highest value in case of a.Mild steel and mild steel b.Mild steel and copper c.Cast iron and steel d.Rope and wood e.Any of the above loctions

Description : The coefficient of static friction will have the highest value in case of a.Mild steel and mild steel b.Mild steel and copper c.Cast iron and steel d.Rope and wood e.Any of the above loctions

Last Answer : d. Rope and wood