The advantages of electrometric bearings are a) Permits movement of the structure in all directions b) Serves as a shock absorber due to anti-vibration properties of elestomeric c) better dispersion of longitudinal forces to the approaches d) All of the above*

The advantages of electrometric bearings are  
a) Permits movement of the structure in all directions
b) Serves as a shock absorber due to anti-vibration properties of elestomeric c) better dispersion of longitudinal forces to the approaches
d) All of the above*
by

1 Answer

Answer :

d) All of the above*
by

Related questions

Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a measure of its capacity and is equal to the residence time when the density of reaction mixture is constant (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty (D) In an ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Description : Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a ... ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Last Answer : (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty

If a material has identical properties in all directions, it is called (a) Elastic (b) Plastic (c) Isotropic (d) Homogeneous

Description : If a material has identical properties in all directions, it is called (a) Elastic (b) Plastic (c) Isotropic (d) Homogeneous

Last Answer : (c) Isotropic

Bearings are provided in bridges to transfer the load to a) Super structure b) Track c) Embankment d) Sub structure*

Description : Bearings are provided in bridges to transfer the load to a) Super structure b) Track c) Embankment d) Sub structure*

Last Answer : d) Sub structure*

There should not be any combination joint on level crossing proper and its approaches up to a) 15 meters b) 30 meters c) 40 meters d) 50 meters

Description : There should not be any combination joint on level crossing proper and its approaches up to a) 15 meters b) 30 meters c) 40 meters d) 50 meters

Last Answer : d) 50 meters

Stop boards on either side of approaches of all unmanned level crossings shall be provided at -------------from the centre line of nearest track. a) 3meters b) 5 meters* c) 6 meters d) 10 meters

Description : Stop boards on either side of approaches of all unmanned level crossings shall be provided at -------------from the centre line of nearest track. a) 3meters b) 5 meters* c) 6 meters d) 10 meters

Last Answer : b) 5 meters*

Speed breaker has to be provided on road approaches of level crossing at maximum feasible distance within Railway boundary but not exceeding a) 10 meters b) 15 meters c) 20 meters* d) 200 meters

Description : Speed breaker has to be provided on road approaches of level crossing at maximum feasible distance within Railway boundary but not exceeding a) 10 meters b) 15 meters c) 20 meters* d) 200 meters

Last Answer : c) 20 meters*

Wing walls and return walls are provided to retain a) earth on approaches b) ballast c) track on approaches d) none

Description : Wing walls and return walls are provided to retain a) earth on approaches b) ballast c) track on approaches d) none

Last Answer : a) earth on approaches

Greasing of bearings of Steel girder bridges is done once in years.

Description : Greasing of bearings of Steel girder bridges is done once in years.

Last Answer : Three

Elastomeric bearings are made of natural or synthetic rubber of shore hardness of approximately. a) 30 to 40 b) 50 to 70* c) 40 to 50 d) 60 to 70

Description : Elastomeric bearings are made of natural or synthetic rubber of shore hardness of approximately. a) 30 to 40 b) 50 to 70* c) 40 to 50 d) 60 to 70

Last Answer : b) 50 to 70

Mostly long span rail-cum road bridges are provided with a) rocker & roller bearings b) segmental roller with oil bath* c) Sliding bearings d) centralised bearings

Description : Mostly long span rail-cum road bridges are provided with a) rocker & roller bearings b) segmental roller with oil bath* c) Sliding bearings d) centralised bearings

Last Answer : b) segmental roller with oil bath

Bearings for plate girders are -- a) roller bearing b) sliding bearings c) centralised articulated bearings* d) None of the above

Description : Bearings for plate girders are -- a) roller bearing b) sliding bearings c) centralised articulated bearings* d) None of the above

Last Answer : c) centralised articulated bearings*

Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Description : Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Last Answer : a. Increases the angle of descent without increasing the airspeed

If digital DRT is calibrated for 300 mm longitudinal wave using 00 double crystal probe then 60kg rail ---------peak will appear at (i) 5.2 (ii) 5.7* (iii) 7.8 (iv) 8.6

Description : If digital DRT is calibrated for 300 mm longitudinal wave using 00 double crystal probe then 60kg rail ---------peak will appear at (i) 5.2 (ii) 5.7* (iii) 7.8 (iv) 8.6

Last Answer : ii) 5.7*

Tandem rig test with 450 probe for AT weld detects. (i) Horizontal longitudinal defect in weld. (ii) Vertical oriented defect in AT weld.* (iii) Transverse defect in AT weld. (iv) Defect in flange of AT welds.

Description : Tandem rig test with 450 probe for AT weld detects. (i) Horizontal longitudinal defect in weld. (ii) Vertical oriented defect in AT weld.* (iii) Transverse defect in AT weld. (iv) Defect in flange of AT welds.

Last Answer : (ii) Vertical oriented defect in AT weld.*

A rural water supply serves a population of 10, 000 at the rate of 50 litres per capita per day . For the chlorine dose of 2 PPM the required amount of bleaching powder with 20% available chlorine will be a. 0.5 kg b. 5 kg * c. 10 kg d. 15 kg

Description : A rural water supply serves a population of 10, 000 at the rate of 50 litres per capita per day . For the chlorine dose of 2 PPM the required amount of bleaching powder with 20% available chlorine will be a. 0.5 kg b. 5 kg * c. 10 kg d. 15 kg

Last Answer : b. 5 kg

In which of the following directions, the strength of timber is maximum a) Parallel to grains* b) 45 degree to grains c) Perpendicular to grains d) same in all directions

Description : In which of the following directions, the strength of timber is maximum a) Parallel to grains* b) 45 degree to grains c) Perpendicular to grains d) same in all directions

Last Answer : a) Parallel to grains*

Addition of pyrazinamide and ethambutol for the first two months to the isoniazid + rifampin therapy of tuberculosis serves the following purpose(s): A. Reduces the total duration of therapy to 6 months B. Produces more rapid sputum conversion C. Permits reduction of rifampin dose D. Both ‘A’ and ‘B’ are correct

Description : Addition of pyrazinamide and ethambutol for the first two months to the isoniazid + rifampin therapy of tuberculosis serves the following purpose(s): A. Reduces the total duration of therapy to 6 months B. ... sputum conversion C. Permits reduction of rifampin dose D. Both A' and B' are correct

Last Answer : D. Both ‘A’ and ‘B’ are correc

Heavy water (D2O) in a nuclear reactor serves as a (A) Coolant (B) Moderator (C) Both (A) & (B) (D) Neutron absorber

Description : Heavy water (D2O) in a nuclear reactor serves as a (A) Coolant (B) Moderator (C) Both (A) & (B) (D) Neutron absorber

Last Answer : (C) Both (A) & (B)

Can I replace the front fork on my bicycle with a suspension/shock absorber type fork. Should it be done by a pro?

Description : Can I replace the front fork on my bicycle with a suspension/shock absorber type fork. Should it be done by a pro?

Last Answer : You can change the fork and I figure it should probably be done by someone who knows what they are doing.

I need a central shock absorber for Java

Description : Cheap

Last Answer : Need Answer

Does the Casio watch have a built-in shock absorber?

Description : Does the Casio watch have a built-in shock absorber?

Last Answer : Yes, the casio watch has a built in shock absorber.

Lead is (A) Not resistant to corrosion (B) Used as a cathodic material (C) Not used as pigment (in its compound forms) for paints (D) Used as a shock absorber (in mattress form) between the foundation and steel framework of skyscraper buildings

Description : Lead is (A) Not resistant to corrosion (B) Used as a cathodic material (C) Not used as pigment (in its compound forms) for paints (D) Used as a shock absorber (in mattress form) between the foundation and steel framework of skyscraper buildings

Last Answer : (D) Used as a shock absorber (in mattress form) between the foundation and steel framework of skyscraper buildings

The tissues which act as shock absorber is

Description : The tissues which act as shock absorber is 

Last Answer : adipose tissue.

V-Belt has efficiency and its works as a Shock absorber. a. Low c) High b. Very low d) Very High

Description : V-Belt has efficiency and its works as a Shock absorber. a. Low c) High b. Very low d) Very High

Last Answer : High

Explain the constructional features of Gas filled shock Absorber with sketch.

Description : Explain the constructional features of Gas filled shock Absorber with sketch.

Last Answer : Features: 1. Control tire motion better than non gas shock absorber 2. Vibration is reduced 3. Reduced aeration. 4. Improved handling.

State the function of Shock Absorber

Description : State the function of Shock Absorber

Last Answer : Function of Shock Absorber: The shock absorber is a part of suspension system used as springing device to compromise between flexibility and stiffness. It absorbs the energy of shock converted into the vertical movement of the axle by providing damping and dissipating the same in to heat.

In a dynamic vibration absorber system, under tuned conditions which of the following relation holds good? A K 1 K 2 =M 1 M 2 B K 1 M 2 =M 1 K 2 C K 1 M 1 = K 2 M 2 D none of the mentioned

Description : In a dynamic vibration absorber system, under tuned conditions which of the following relation holds good? A K 1 K 2 =M 1 M 2 B K 1 M 2 =M 1 K 2 C K 1 M 1 = K 2 M 2 D none of the mentioned

Last Answer : B K 1 M 2 =M 1 K 2

Dynamic vibration absorber is suitable for A varying speed machines B constant speed machines C Zero speed range machines D None of the mentioned

Description : Dynamic vibration absorber is suitable for A varying speed machines B constant speed machines C Zero speed range machines D None of the mentioned

Last Answer : B constant speed machines

The two resonant frequency ratio (ω/ ω2) in a dynamic vibration absorber system for a mass ratio 0.2 are given by A) 0 ; 1.0 B) 0.801 ; 1.248 C) 0.458 ; 1.124 D) 0.642 ; 1.558

Description : The two resonant frequency ratio (ω/ ω2) in a dynamic vibration absorber system for a mass ratio 0.2 are given by A) 0 ; 1.0 B) 0.801 ; 1.248 C) 0.458 ; 1.124 D) 0.642 ; 1.558

Last Answer : B) 0.801 ; 1.248

Centrifugal absorber is used to reduce A) Centrifugal force in rotating system B) Torsional vibration of rotating system C) Vibration in linear system D) Transverse vibrations

Description : Centrifugal absorber is used to reduce A) Centrifugal force in rotating system B) Torsional vibration of rotating system C) Vibration in linear system D) Transverse vibrations

Last Answer : B) Torsional vibration of rotating system

Which of the following condition should be satisfied in the design of a vibration absorber ? A) Natural frequency of the auxiliary system should be equal to the natural frequency of the main system B) Natural frequency of the auxiliary system should be equal to the half natural frequency of the main systemC) Natural frequency of the auxiliary system should be fall in between natural frequency of the main system and the frequency of excitation D) Natural frequency of the auxiliary system should be twice natural frequency of the main system

Description : Which of the following condition should be satisfied in the design of a vibration absorber ? A) Natural frequency of the auxiliary system should be equal to the natural frequency of the main ... D) Natural frequency of the auxiliary system should be twice natural frequency of the main system

Last Answer : A) Natural frequency of the auxiliary system should be equal to the natural frequency of the main system

Dynamic vibration absorber is suitable for A) Constant speed machine B) Varying speed machine C) zero speed machine D) None of the above

Description : Dynamic vibration absorber is suitable for A) Constant speed machine B) Varying speed machine C) zero speed machine D) None of the above

Last Answer : A) Constant speed machine

When ≠ , the absorber is known as A. Untuned vibration absorber B. Tuned vibration absorber C. Both of above D. None of these

Description : When ≠ , the absorber is known as A. Untuned vibration absorber B. Tuned vibration absorber C. Both of above D. None of these

Last Answer : A. Untuned vibration absorber

When = , the absorber is known as A. Untuned vibration absorber B. Tuned vibration absorber C. Both of above D. None of these

Description : When = , the absorber is known as A. Untuned vibration absorber B. Tuned vibration absorber C. Both of above D. None of these

Last Answer : B. Tuned vibration absorber

Dynamic vibration absorber is suitable for A. Constant speed machines B. Varying speed machines C. Zero speed range machines D. None of the above

Description : Dynamic vibration absorber is suitable for A. Constant speed machines B. Varying speed machines C. Zero speed range machines D. None of the above

Last Answer : A. Constant speed machines

Research approaches are Options: A) Longitudinal and cross-sectional B) Oblique and horizontal C) Long and short section D) None of the above

Description : Research approaches are Options: A) Longitudinal and cross-sectional B) Oblique and horizontal C) Long and short section D) None of the above

Last Answer : A) Longitudinal and cross-sectional

In Longitudinal approaches primarily the researches are related with Options: A) Temporal sequence B) Eugenics C) Sample D) None of the above

Description : In Longitudinal approaches primarily the researches are related with Options: A) Temporal sequence B) Eugenics C) Sample D) None of the above

Last Answer : A) Temporal sequence

On electrical generators one of the bearings is isolated from the bedplate. This insulating block should not be painted and must be kept clean to ___________. A. protect operating personnel from shock B. create an isolated ground for the instrumentation C. allow for the expansion of the generator away from the prime mover as it warms up D. eliminate shaft currents to prevent damaging the bearings

Description : On electrical generators one of the bearings is isolated from the bedplate. This insulating block should not be painted and must be kept clean to ___________. A. protect operating personnel from shock ... the prime mover as it warms up D. eliminate shaft currents to prevent damaging the bearings

Last Answer : Answer: D

In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. (a) 1 (b) 2 (c) 3 (d) 4

Last Answer : (b) 2

In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Description : In angular contact bearings, ____ bearings are required to take thrust load in both directions. a) 1 b) 4 c) 2 d) 3

Last Answer : c) 2

ACD means (a) Anti collision Devise* (b) Accidents causing death (c) Accidents causing derailment (d) None of the above

Description : ACD means (a) Anti collision Devise* (b) Accidents causing death (c) Accidents causing derailment (d) None of the above

Last Answer : (a) Anti collision Devise*

Reflections in many directions ∙ a. Diffuse reflection ∙ b. Diffraction ∙ c. Scattering ∙ d. Dispersion

Description : Reflections in many directions ∙ a. Diffuse reflection ∙ b. Diffraction ∙ c. Scattering ∙ d. Dispersion

Last Answer : a. Diffuse reflection

Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Description : Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Last Answer : A) Soundness*

Quicksand is a) Moist sand containing a small percentage of clay b) Is a condition which generally occurs in coarse sands c) Is a condition in which cohesive properties of soil increase rapidly d) Is a condition in which a cohesion less soil loses its strength because of upward flow of water

Description : Quicksand is a) Moist sand containing a small percentage of clay b) Is a condition which generally occurs in coarse sands c) Is a condition in which cohesive properties of soil increase rapidly d) Is a condition in which a cohesion less soil loses its strength because of upward flow of water

Last Answer : d) Is a condition in which a cohesion less soil loses its strength because of upward flow of water

In a longitudinal wave, the vibration of particles and the direction of wave are in

Description : In a longitudinal wave, the vibration of particles and the direction of wave are in

Last Answer : the same direction.

Which of the following is a type of free vibration? A Longitudinal vibrations B Transverse vibrations C Torsional vibrations D A, B and C

Description : Which of the following is a type of free vibration? A Longitudinal vibrations B Transverse vibrations C Torsional vibrations D A, B and C

Last Answer : D A, B and C

Which of the following is a type of free vibration? A. Longitudinal vibrations B. Transverse vibrations C. Torsional vibrations D. A, B and C

Description : Which of the following is a type of free vibration? A. Longitudinal vibrations B. Transverse vibrations C. Torsional vibrations D. A, B and C

Last Answer : D. A, B and C

Critical speed of shaft and disc system A) Is equal to natural frequency of the system in transverse vibration B) Is equal to natural frequency of the system in torsional vibration C) Is equal to natural frequency of the system in longitudinal vibration D) Bears no relationship to any of the system natural frequency

Description : Critical speed of shaft and disc system A) Is equal to natural frequency of the system in transverse vibration B) Is equal to natural frequency of the system in torsional vibration C) Is ... of the system in longitudinal vibration D) Bears no relationship to any of the system natural frequency

Last Answer : A) Is equal to natural frequency of the system in transverse vibration

In a spring mass system of mass m and stiffness k, the end of the spring are securely fixed and mass is attached to intermediate point of spring. The natural frequency of longitudinal vibration of the system A) Is maximum when mass is attached to mid point of the spring B) Is minimum when mass is attached to mid point of the spring C) Decreases as the distance from the top end where mass is attached decreases D) Decreases as the distance from the bottom end where mass is attached decreases

Description : In a spring mass system of mass m and stiffness k, the end of the spring are securely fixed and mass is attached to intermediate point of spring. The natural frequency of longitudinal ... is attached decreases D) Decreases as the distance from the bottom end where mass is attached decreases

Last Answer : B) Is minimum when mass is attached to mid point of the spring

In the spring mass system if the mass of the system is doubled with spring stiffness halved, the natural frequency of longitudinal vibration A) Remained unchanged B) Is doubled C) Is halved D) Is quadruped

Description : In the spring mass system if the mass of the system is doubled with spring stiffness halved, the natural frequency of longitudinal vibration A) Remained unchanged B) Is doubled C) Is halved D) Is quadruped

Last Answer : C) Is halved