Which of the following gradients exerts maximum influence on properties of steel? (A) Iron (B) Carbon (C) Manganese (D) Sulphur

Which of the following gradients exerts maximum influence on properties of steel?
(A) Iron
(B) Carbon
(C) Manganese
(D) Sulphur
by

1 Answer

Answer :

Answer: Option B
by

Related questions

Which of the following exercises most powerful influence on the mechanical properties of steel? (A) Manganese (B) Carbon (C) Phosphorous (D) Silicon

Description : Which of the following exercises most powerful influence on the mechanical properties of steel? (A) Manganese (B) Carbon (C) Phosphorous (D) Silicon

Last Answer : (B) Carbon

__________ is added in low carbon steel to raise its yield point. (A) Sulphur (B) Phosphorous (C) Silicon (D) Manganese

Description : __________ is added in low carbon steel to raise its yield point. (A) Sulphur (B) Phosphorous (C) Silicon (D) Manganese

Last Answer : (D) Manganese

__________ is the most important element, which controls the physical properties of steel. (A) Manganese (B) Silicon (C) Carbon (D) Vanadium

Description : __________ is the most important element, which controls the physical properties of steel. (A) Manganese (B) Silicon (C) Carbon (D) Vanadium

Last Answer : (C) Carbon

Three basic raw materials which are needed in large quantities for production of steel are (A) Iron ore, coal and sulphur (B) Iron ore, carbon and sulphur (C) Iron ore, coal and lime stone (D) Iron ore, carbon and lime stone

Description : Three basic raw materials which are needed in large quantities for production of steel are (A) Iron ore, coal and sulphur (B) Iron ore, carbon and sulphur (C) Iron ore, coal and lime stone (D) Iron ore, carbon and lime stone

Last Answer : Answer: Option C

Work hardenable alloy steel used to make the bucket wheel excavators, blades of bulldozers and other earth moving equipments contain iron, carbon and (A) Manganese (B) Silicon (C) Nickel (D) Chromium

Description : Work hardenable alloy steel used to make the bucket wheel excavators, blades of bulldozers and other earth moving equipments contain iron, carbon and (A) Manganese (B) Silicon (C) Nickel (D) Chromium

Last Answer : (A) Manganese

Which material is suitable for shaft material? a. High speed steel b. Stainless steel or high carbon steel c. Grey cast iron d. Steel having approx. 0.4% carbon and 0.8% manganese

Description : Which material is suitable for shaft material? a. High speed steel b. Stainless steel or high carbon steel c. Grey cast iron d. Steel having approx. 0.4% carbon and 0.8% manganese

Last Answer : d. Steel having approx. 0.4% carbon and 0.8% manganese

The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Description : The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Last Answer : Answer: Option D

Brittleness induced due to the presence of sulphur in steel can be reduced by adding (A) Manganese (B) Magnesium (C) Vanadium (D) Copper

Description : Brittleness induced due to the presence of sulphur in steel can be reduced by adding (A) Manganese (B) Magnesium (C) Vanadium (D) Copper

Last Answer : (A) Manganese

Brittleness induced due to the presence of sulphur in steel can be reduced by adding (A) Manganese (B) Magnesium (C) Vanadium (D) Copper

Description : Brittleness induced due to the presence of sulphur in steel can be reduced by adding (A) Manganese (B) Magnesium (C) Vanadium (D) Copper

Last Answer : r: Option A

Floating gradients are generally provided (A) Along maximum gradients (B) Along minimum gradients (C) At summit curves (D) At valley curves

Description : Floating gradients are generally provided (A) Along maximum gradients (B) Along minimum gradients (C) At summit curves (D) At valley curves

Last Answer : Answer: Option C

Iron ore may contain (A) Carbon (B) Silicon (C) Phosphorus and manganese (D) All the above

Description : Iron ore may contain (A) Carbon (B) Silicon (C) Phosphorus and manganese (D) All the above

Last Answer : Answer: Option D

Minerals known to be required in large amounts for plant growth include (a) potassium, phosphorus, selenium, boron (b) magnesium, sulphur, iron, zinc (c) phosphorus, potassium, sulphur, calcium (d) calcium, magnesium, manganese, copper.

Description : Minerals known to be required in large amounts for plant growth include (a) potassium, phosphorus, selenium, boron (b) magnesium, sulphur, iron, zinc (c) phosphorus, potassium, sulphur, calcium (d) calcium, magnesium, manganese, copper.

Last Answer : (c) phosphorus, potassium, sulphur, calcium

Classify the following materials as metals and non-metals : Hydrogen, Sulphur, Selenium, Manganese, Calcium, Platinum, Gold, Silica, Polyester, Wood, Glass, Iron

Description : Classify the following materials as metals and non-metals : Hydrogen, Sulphur, Selenium, Manganese, Calcium, Platinum, Gold, Silica, Polyester, Wood, Glass, Iron 

Last Answer : Metals: calcium , manganese, platinum, gold , iron Non- metals: hydrogen, Sulphur, silica, polyester, wood, glass, selenium

Weld decay is caused by the formation of a compound with carbon. The other element in this compound is: a) Manganese b) Sulphur c) Chromium d) Nickel

Description : Weld decay is caused by the formation of a compound with carbon. The other element in this compound is: a) Manganese b) Sulphur c) Chromium d) Nickel

Last Answer : c) Chromium

The ________ is a person within a reference group who, because of special skills, knowledge, personality, or other characteristics, exerts influence on others 1. facilitator 2. reference actor 3. opinion leader 4. social role player 5. none of these

Description : The ________ is a person within a reference group who, because of special skills, knowledge, personality, or other characteristics, exerts influence on others 1. facilitator 2. reference actor 3. opinion leader 4. social role player 5. none of these

Last Answer : opinion leader

Stainless steel resists corrosion due to (A) Carbon (B) Sulphur (C) Vanadium (D) Chromium

Description : Stainless steel resists corrosion due to (A) Carbon (B) Sulphur (C) Vanadium (D) Chromium

Last Answer : Answer: Option D

______is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ? (a) Grey cast-iron (b) Cast steel (c) High carbon steel (d) Stainless steel

Description : ______is extensively used for those portions of magnetic circuit which carry steady flux and need superior mechanical properties ? (a) Grey cast-iron (b) Cast steel (c) High carbon steel (d) Stainless steel

Last Answer : (b) Cast steel

(a) 1. Name the private sector iron and steel plant of India. [2] 2. From where does it get its supply of: 1. Iron ore 2. Manganese 3. Coal? -Geography

Description : (a) 1. Name the private sector iron and steel plant of India. [2] 2. From where does it get its supply of: 1. Iron ore 2. Manganese 3. Coal? -Geography

Last Answer : 1. Tata Iron and Steel Industry, Jamshedpur. 2. 1. Iron Ore: Singhbhum, Mayurbhanj. 2. Manganese: Noamundi. 3. Coal: Jharia.

Which of the following is false? (a) Mica is usually found in metamorphic and igneous rocks (b) Aluminium has the advantage over iron as it is resistant to corrosion (c) line is mostly used in galvanising iron and steel goods (d) Manganese is largely used in making fertilizers

Description : Which of the following is false? (a) Mica is usually found in metamorphic and igneous rocks (b) Aluminium has the advantage over iron as it is resistant to corrosion (c) line is mostly used in galvanising iron and steel goods (d) Manganese is largely used in making fertilizers

Last Answer : Ans: (d)

Manganese is added in low carbon steel to A. Make the steel tougher and harder B. Raise the yield point C. Make the steel ductile and of good bending qualities D. All of the above

Description : Manganese is added in low carbon steel to A. Make the steel tougher and harder B. Raise the yield point C. Make the steel ductile and of good bending qualities D. All of the above

Last Answer : C. Make the steel ductile and of good bending qualities

The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel. (A) Carbon (B) Manganese (C) Both 'a' nor 'b' (D) Neither 'a' nor 'b'

Description : The 'transition temperature' for ductile to brittle behaviour of steel increases with increase in the __________ content in steel. (A) Carbon (B) Manganese (C) Both 'a' nor 'b' (D) Neither 'a' nor 'b'

Last Answer : (A) Carbon

Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Description : Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Last Answer : d) Austenitic stainless steels

Red short iron cracks when bent due to the presence of (A) Sulphur (B) Carbon (C) Phosphorus (D) Silicon

Description : Red short iron cracks when bent due to the presence of (A) Sulphur (B) Carbon (C) Phosphorus (D) Silicon

Last Answer : Answer: Option A

From any point on the surface with a given inclination (A) Only one contour gradient is possible (B) Two contour gradients are possible (C) Indefinite contour gradients are possible (D) All of the above

Description : From any point on the surface with a given inclination  (A) Only one contour gradient is possible  (B) Two contour gradients are possible  (C) Indefinite contour gradients are possible  (D) All of the above

Last Answer : (C) Indefinite contour gradients are possible 

An ideal vertical curve to join two gradients, is (A) Circular (B) Parabolic (C) Elliptical (D) Hyperbolic

Description : An ideal vertical curve to join two gradients, is (A) Circular (B) Parabolic (C) Elliptical (D) Hyperbolic

Last Answer : (B) Parabolic

The total length of a valley formed by two gradients - 3% and + 2% curve between the two tangent points to provide a rate of change of centrifugal acceleration 0.6 m/sec2 , for a design speed 100 kmph, is (A) 16.0 m (B) 42.3 m (C) 84.6 m (D) None of these

Description : The total length of a valley formed by two gradients - 3% and + 2% curve between the two tangent points to provide a rate of change of centrifugal acceleration 0.6 m/sec2 , for a design speed 100 kmph, is (A) 16.0 m (B) 42.3 m (C) 84.6 m (D) None of these

Last Answer : Answer: Option C

The gradients of trace cuts for hilly roads, are kept (A) Equal to ruling gradient (B) 10 to 20 per cent easier than ruling gradients (C) 10 to 20 per cent steeper than ruling gradients (D) None of these

Description : The gradients of trace cuts for hilly roads, are kept (A) Equal to ruling gradient (B) 10 to 20 per cent easier than ruling gradients (C) 10 to 20 per cent steeper than ruling gradients (D) None of these

Last Answer : Answer: Option B

The difference in gradients after full super-elevation and the initial alignment of a road, is known as (A) Ruling gradient(B) Rising gradient (C) Compensated gradient (D) Differential gradient

Description : The difference in gradients after full super-elevation and the initial alignment of a road, is known as (A) Ruling gradient (B) Rising gradient (C) Compensated gradient (D) Differential gradient

Last Answer : Answer: Option D

Depending on the chemical composition and mechanical properties, iron may be classified as (A) Cast iron (B) Wrought iron (C) Steel (D) All the above

Description : Depending on the chemical composition and mechanical properties, iron may be classified as (A) Cast iron (B) Wrought iron (C) Steel (D) All the above

Last Answer : Answer: Option D

The system in which high tensile alloy steel bars (silica manganese steel) are used as prestressing tendons, is known as (A) Freyssinet system (B) Magnel-Blaton system (C) C.C.L. standard system (D) Lee-McCall system

Description : The system in which high tensile alloy steel bars (silica manganese steel) are used as prestressing tendons, is known as (A) Freyssinet system (B) Magnel-Blaton system (C) C.C.L. standard system (D) Lee-McCall system

Last Answer : Answer: Option D

The steel used for rails under heavy traffic and on sharp curves, is (A) Nickel steel (B) Chrome steel (C) Manganese steel (D) Vanadium steel

Description : The steel used for rails under heavy traffic and on sharp curves, is (A) Nickel steel (B) Chrome steel (C) Manganese steel (D) Vanadium steel

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) Excess quantities of iron and manganese in water, cause discolouration of clothes (B) Lead and barium salts have toxic effect (C) Higher copper content affects the lungs (D) All the above

Description : Pick up the correct statement from the following: (A) Excess quantities of iron and manganese in water, cause discolouration of clothes (B) Lead and barium salts have toxic effect (C) Higher copper content affects the lungs (D) All the above

Last Answer : (D) All the above

Hypogonadism develops due to deficiency of (A) Sulphur (B) Cobalt (C) Zinc (D) Manganese

Description : Hypogonadism develops due to deficiency of (A) Sulphur (B) Cobalt (C) Zinc (D) Manganese

Last Answer : Answer : C

Physical properties of a permeant which influence permeability are(A) Viscosity only (B) Unit weight only (C) Both viscosity and unit weight (D) None of the above

Description : Physical properties of a permeant which influence permeability are (A) Viscosity only (B) Unit weight only (C) Both viscosity and unit weight (D) None of the above

Last Answer : Answer: Option C

Back fill with a sloping surface exerts a total active pressure Pa on the wall of height H and acts at (A) H/4 above the base parallel to base (B) H/2 above the base parallel to base (C) H/3 above the base parallel to base (D) H/5 above the base parallel to base

Description : Back fill with a sloping surface exerts a total active pressure Pa on the wall of height H and acts at (A) H/4 above the base parallel to base (B) H/2 above the base parallel to base (C) H/3 above the base parallel to base (D) H/5 above the base parallel to base

Last Answer : Answer: Option C

Which one of the following contains maximum percentage of carbon? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Description : Which one of the following contains maximum percentage of carbon? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Last Answer : (1) Cast iron Explanation: Cast Iron is a hard, brittle, nonmalleable iron-carbon alloy, cast into shape, containing 2 to 4.5 percent carbon. Steels contain less than 2% and usually less than 1% carbon, ... percent carbon. Wrought iron is an iron alloy with very low carbon (0.04 to 0.08%) content.

Which one of the following contains maximum percentage of carbon ? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Description : Which one of the following contains maximum percentage of carbon ? (1) Cast iron (2) Stainless steel (3) Wrought iron (4) High speed steel

Last Answer : Cast iron

The steel used in R.C.C. work is (A) Stainless steel (B) Mild steel (C) High carbon steel (D) Wrought iron

Description : The steel used in R.C.C. work is (A) Stainless steel (B) Mild steel (C) High carbon steel (D) Wrought iron

Last Answer : Answer: Option B

The process of decarbonising the pig iron completely and then adding proper percentage of carbon for manufacturing steel, is called (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth process

Description : The process of decarbonising the pig iron completely and then adding proper percentage of carbon for manufacturing steel, is called (A) Cementation process (B) Crucible process (C) Bessemer process (D) Open hearth process

Last Answer : Answer: Option A

Which of the following is the purest form of iron? (A) Cast iron (B) Wrought iron (C) Mild steel (D) High carbon steel

Description : Which of the following is the purest form of iron? (A) Cast iron (B) Wrought iron (C) Mild steel (D) High carbon steel

Last Answer : Answer: Option B

Sulphur melting pit in the sulphuric acid plant is made of (A) Lead lined stainless steel (B) Cast iron (C) Steel or cement-brick lined (D) Hard wood

Description : Sulphur melting pit in the sulphuric acid plant is made of (A) Lead lined stainless steel (B) Cast iron (C) Steel or cement-brick lined (D) Hard wood

Last Answer : (C) Steel or cement-brick lined

Silico-manganese steels (containing 0.7% Mn, 0.5% C and 2% Si) (A) Do not require heat treatment for any of its applications (B) Are used for leaf and coiled springs (C) Do not have good resilience properties (D) Is tempered at 850°C

Description : Silico-manganese steels (containing 0.7% Mn, 0.5% C and 2% Si) (A) Do not require heat treatment for any of its applications (B) Are used for leaf and coiled springs (C) Do not have good resilience properties (D) Is tempered at 850°C

Last Answer : (B) Are used for leaf and coiled springs

Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Last Answer : (C) Machinability

Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505 (D) 0.805

Description : Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505 (D) 0.805

Last Answer : (B) 0.055

Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505

Description : Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505

Last Answer : Option A

Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505 (D) 0.805

Description : Maximum permissible sulphur content in steel is __________ percent. (A) 0.015 (B) 0.055 (C) 0.505 (D) 0.805

Last Answer : Option A

Pick up the correct statement from the following: (A) Steel produced by open hearth process is milder than that obtained by the Bessemer process (B) Engineers prefer open hearth steel for structural purpose as it is more homogenous (C) Basic Bessemer process is suitable for converting poor ore containing a large proportion of sulphur and phosphorus into steel

Description : Pick up the correct statement from the following: (A) Steel produced by open hearth process is milder than that obtained by the Bessemer process (B) Engineers prefer open hearth steel ... is suitable for converting poor ore containing a large proportion of sulphur and phosphorus into steel

Last Answer : Answer: Option D

$ Positive diffusion occurs against the concentration gradients. ! Osmosis does not require a semi-permeable membrane.

Description : $ Positive diffusion occurs against the concentration gradients. ! Osmosis does not require a semi-permeable membrane.

Last Answer : $ Positive diffusion occurs against the concentration gradients. ! Osmosis does not require a semi-permeable ... D. If both As and R are wrong.

The weather map shows many pressure gradients close together. What things should you take to be prepared for the day's weather?

Description : The weather map shows many pressure gradients close together. What things should you take to be prepared for the day's weather?

Last Answer : Tightly-packed isobars portend strong winds (A+) answer a hat or scarf because of high winds

The weather map shows many pressure gradients close together. What things should you take to be prepared for the day's weather?

Description : The weather map shows many pressure gradients close together. What things should you take to be prepared for the day's weather?

Last Answer : Tightly-packed isobars portend strong winds (A+) answer a hat or scarf because of high winds