What Are The Advantages Of Induced Draft Cooling Tower Over Forced Draft Cooling Tower?

What Are The Advantages Of Induced Draft Cooling Tower Over Forced Draft Cooling Tower?
by

1 Answer

Answer :

1. The outlet water comes in contact with the driest air and warmest water comes in contact with most humid air.
2. The re-circulation is seldom a problem.
3. The first cost is low due to the reduction in pump power consumption.
by

Related questions

Define Forced Draft And Induced Draft Cooling Towers?

Description : Define Forced Draft And Induced Draft Cooling Towers?

Last Answer : If the fan is located at the bottom of the tower and air is blown by the fan up through the descending water it is called as forced draft cooling towers. If the fan is located at the top of the ... on the tower's side and drawn up and discharge through the fan casing, it is called as induced draft.

What Are The Advantages Of Hyperbolic Natural-draft Cooling Towers?

Description : What Are The Advantages Of Hyperbolic Natural-draft Cooling Towers?

Last Answer :  Since no fans are used power cost and auxiliary equipments cost is reduced.  Hyperbolic tower chimney creates its own draft even when there is no wind.  Ground fogging and warm air re-circulation are avoided in hyperbolic towers.  The structure is more or less self-supported.

When the temperature and humidity of air is low, we usually use __________ draft cooling tower. (A) Natural (B) Forced (C) Induced (D) None of these

Description : When the temperature and humidity of air is low, we usually use __________ draft cooling tower. (A) Natural (B) Forced (C) Induced (D) None of these

Last Answer : (A) Natural

The most efficient cooling tower out of the following is (A) Induced draft (B) Forced draft (C) Natural draft (D) Atmospheric

Description : The most efficient cooling tower out of the following is (A) Induced draft (B) Forced draft (C) Natural draft (D) Atmospheric

Last Answer : (A) Induced draft

Pick out the wrong statement pertaining to the cooling towers. (A) In case of induced draft cooling tower, the fan is placed at the top of the tower (B) Effectiveness of forced draft cooling tower is reduced by the recirculation of the humid and hot discharged air (C) A natural draft cooling tower is recommended to be used, when the air humidity is low and air temperature is also low (D) Effectiveness of a mechanical draft cooling tower is reduced with increase in air wet-bulb temperature

Description : Pick out the wrong statement pertaining to the cooling towers. (A) In case of induced draft cooling tower, the fan is placed at the top of the tower (B) Effectiveness of ... Effectiveness of a mechanical draft cooling tower is reduced with increase in air wet-bulb temperature

Last Answer : (D) Effectiveness of a mechanical draft cooling tower is reduced with increase in air wet-bulb temperature

How Mechanical Draft Cooling Towers Are Classified?

Description : How Mechanical Draft Cooling Towers Are Classified?

Last Answer : Mechanical draft cooling tower is classified into three types: 1. Forced draft tower. 2. Induced draft counterflow tower. 3. Induced draft cross flow tower.

What Are The Advantages Of Forced Draught System?

Description : What Are The Advantages Of Forced Draught System?

Last Answer :  Since the fan handles cold air, the fan size and the power required are less.  No need of water cooled bearings because the air being handled is cold air,  Pressure throughout the system is above atmospheric pressure so the air leakage into the furnace is reduced.

In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of theoretical plate calculation for distillation column (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Description : Pick out the wrong statement. (A) Different solids have different equilibrium moisture curves (B) Total condenser or reboiler is considered equivalent to one theoretical plate in McCabe-Thiele method of ... (D) Even a forced draft cooling tower cannot cool water below the wet bulb temperature

Last Answer : (C) Heat removal load on cooler remains constant, even with increase of the reflux ratio in a distillation column

In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

Description : Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

Last Answer : Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

The equipment frequently used for adiabatic humidification-cooling operation with recirculating liquid is (A) Natural draft cooling tower (B) Induced draft cooling tower (C) Spray chamber (D) None of these

Description : The equipment frequently used for adiabatic humidification-cooling operation with recirculating liquid is (A) Natural draft cooling tower (B) Induced draft cooling tower (C) Spray chamber (D) None of these

Last Answer : (C) Spray chamber

Explain the construction and working of induced draft cooling tower with neat sketch.

Description : Explain the construction and working of induced draft cooling tower with neat sketch.

Last Answer : Induced draft cooling tower :  Diagram: Construction and working: Cooling towers are employed to cool utility cooling water by direct contact with air. The parts of a cooling tower are ... top pulls the hot air through the fills and cooled water gets collected in the cold water basin.

What Is The Use Of Draft Tube?

Description : What Is The Use Of Draft Tube?

Last Answer : The draft tube is used to regain the kinetic energy of water coming out of reaction turbine. It enables the reaction turbine to be placed over tailrace level.

Write About Forced Draught System?

Description : Write About Forced Draught System?

Last Answer : In this system, the blower (forced draft fan) is located at the base of the boiler near the grate. Air is forced to the furnace by forced fan and the flue gases are forced to chimney through economizer and air preheater.

How The Induced Draught Is Working?

Description : How The Induced Draught Is Working?

Last Answer : In an induced draught system, a blower (induced draft fan) is placed near (or) at the base of the chimney. The fan sucks the flue gas from the furnace creating a partial vacuum inside the ... aid the combustion of fuel. The flue gases drawn by the fan passes through chimney, to the atmosphere.

How The Dry Type Cooling Towers Are Classified?

Description : How The Dry Type Cooling Towers Are Classified?

Last Answer : The dry type cooling towers are classified into two types ‘as follows: 1. Indirect dry type (or) Heller cooling system 2. Direct dry type-cooling system

How The Atmospheric (or) Natural Draught Cooling Towers Are Classified?

Description : How The Atmospheric (or) Natural Draught Cooling Towers Are Classified?

Last Answer : In atmospheric (or) natural cooling towers, the natural air provides the required cooling without the use of fans. This is classified into three types: 1. Natural draft spray filled towers. 2. Natural draft packed type towers. 3. Hyperbolic cooling towers.

Name Different Types Of Cooling Towers?

Description : Name Different Types Of Cooling Towers?

Last Answer : The cooling towers are classified as follows. According to the construction of material: 1. Timber for small tower 2. Ferro concrete for large capacity stations. 3. Multi deck concrete towers for ... air draught: 1. Atmospheric (or) Natural draught cooling system 2. Mechanical draught cooling tower.

What Is The Working Principle Of Cooling Towers?

Description : What Is The Working Principle Of Cooling Towers?

Last Answer : The hot water is sprayed from the top of the tower, while the air is made to flow from the bottom of the tower to the top. This air cools the hot water in the cooling tower. Air evaporates ... and leaves at the top of the tower and cooled water leaves at the bottom and recirculated to the condenser.

What Are The Factors That Affect The Rate Of Evaporation Of Water In Cooling Towers?

Description : What Are The Factors That Affect The Rate Of Evaporation Of Water In Cooling Towers?

Last Answer :  Amount of water surface area exposed.  The time of exposure.  The relative velocity of air passing over the droplets.  The RH of air.  The direction of airflow relative to water.

What Is The Function Of Cooling System In Diesel Power Plant?

Description : What Is The Function Of Cooling System In Diesel Power Plant?

Last Answer : The function of cooling system is to remove heat from the engine cylinder to keep the temperature of the cylinder in low range and extend engine life.

What Are The Advantages Of Gas Cooled Reactor Nuclear Power Plant?

Description : What Are The Advantages Of Gas Cooled Reactor Nuclear Power Plant?

Last Answer : 1. Fuel processing is simple. 2. The use of C02 as coolant completely eliminates the possibility of explosion in reactor. 3. No corrosion problem.

State Some Advantages Of Pressurized Water Reactor?

Description : State Some Advantages Of Pressurized Water Reactor?

Last Answer :  The pressurized water reactor is compact  In this type, water is used as coolant; moderator and reflector water is cheap and available in plenty)  It requires less number of control rods.

What Are The Advantages Of Sodium In Fast-breeder Reactors?

Description : What Are The Advantages Of Sodium In Fast-breeder Reactors?

Last Answer :  Sodium has very low absorption cross-sectional area.  It possess good heat transfer properties at high temperature and low pressure.  It does not react with any of the structural materials used in primary circuits.

What Are The Advantages Of Breeder Reactors?

Description : What Are The Advantages Of Breeder Reactors?

Last Answer :  It gives high power density than any other reactor.  High breeding is possible.  High burn-up of fuel is achievable.  The operation of the reactor is not limited by Xe poisoning.

What Are The Advantages Using Co2 As Coolant?

Description : What Are The Advantages Using Co2 As Coolant?

Last Answer :  Gases do not react chemically with the structural materials.  Gas can attain any temperature for a particular pressure.  They do not absorb neutron.  The leakage of gas will not affect the reactivity.  The gas coolant provides best neutron economy.

What Are Advantages Of Unit (or) Direct System Of Pulverized Fuel Firing?

Description : What Are Advantages Of Unit (or) Direct System Of Pulverized Fuel Firing?

Last Answer : 1. The layout is simple and economical 2. It gives direct control of combustion 3. Coal transportation system is simple 4. Maintenance cost is less

Define The Term Natural Draught And What Are The Advantages Of Natural Draught System?

Description : Define The Term Natural Draught And What Are The Advantages Of Natural Draught System?

Last Answer : The tall chimney creates the natural draught by the temperature difference between hot gases in the chimney and cold atmospheric air outside the chimney. The advantages are:  No external power is required ... at high level.  No maintenance cost.  Capital cost is less than artificial draught.

State Some Advantages Of Fluidized Bed Boilers?

Description : State Some Advantages Of Fluidized Bed Boilers?

Last Answer :  Any type of fuel solid, liquid (or) gaseous fuel (or) domestic and industrial waste can be used in FBC system. Any type of combustible matter can be burned by adjusting the factors as size ... .  High combustion efficiency.  The solid fuel need not be pulverized in fluidized bed boilers.

State Some Advantages Of Regeneration Cycle?

Description : State Some Advantages Of Regeneration Cycle?

Last Answer :  Heat supplied to boiler becomes reduced.  Thermal efficiency is increased since the average temperature of heat addition to the cycle is increased.  Due to bleeding in the turbine, erosion of turbine due to moisture is reduced.

What Are The Important Advantages Of Re Heating?

Description : What Are The Important Advantages Of Re Heating?

Last Answer :  Due to reheating, network done increases.  Heat supply increases.  Thermal efficiency increases.  Due to reheating, the turbine exit dryness fraction increases so moisture decreases so blade erosion becomes minimum so life of the turbine will be increased.

Write About Benson Boiler? State Some Important Advantages Of Benson Boiler?

Description : Write About Benson Boiler? State Some Important Advantages Of Benson Boiler?

Last Answer : Benson boiler is the high pressure, vertical fire tube boiler. This boiler has no drum and is ~designed to operate at critical pressure of 225 bars. Benson boiler has no drum. So the total ... reduced by 20%, when compared to other boilers. The erection of Benson boiler is easier and quicker.

State Important Advantages Of High-pressure Boilers?

Description : State Important Advantages Of High-pressure Boilers?

Last Answer :  The amount of scale formation is less, since the velocity of water through pipes are more.  All parts of the system are heated uniformly, so there is no danger of overheating.

Flue gas from the heating chamber of byproduct coke ovens is removed by (A) Forced draft fan (B) Induced draft fan (C) Steam ejector (D) Natural draft

Description : Flue gas from the heating chamber of byproduct coke ovens is removed by (A) Forced draft fan (B) Induced draft fan (C) Steam ejector (D) Natural draft

Last Answer : (D) Natural draft

Which of the following employs an accessory known as 'drift eliminator'? (A) Multiple effect evaporator (B) Mechanical draft cooling tower (C) Rotary dryer (D) Rotating disc contacto

Description : Which of the following employs an accessory known as 'drift eliminator'? (A) Multiple effect evaporator (B) Mechanical draft cooling tower (C) Rotary dryer (D) Rotating disc contacto

Last Answer : (B) Mechanical draft cooling tower

Use of natural draft cooling tower is practised, when the air has low (A) Humidity (B) Temperature (C) Both 'a' & 'b' (D) Neither 'a' nor 'b'

Description : Use of natural draft cooling tower is practised, when the air has low (A) Humidity (B) Temperature (C) Both 'a' & 'b' (D) Neither 'a' nor 'b'

Last Answer : (C) Both 'a' & 'b

A natural draft cooling tower is filled with wooden grids, which covers about __________ percent of the tower height. (A) 10-15 (B) 30-40 (C) 70-80 (D) 90-100

Description : A natural draft cooling tower is filled with wooden grids, which covers about __________ percent of the tower height. (A) 10-15 (B) 30-40 (C) 70-80 (D) 90-100

Last Answer : (A) 10-15

Which among the following are the components of natural draft cooling tower a) Supply basin b) reinforced concrete c) Hot water distribution d) none of the above

Description : Which among the following are the components of natural draft cooling tower a) Supply basin b) reinforced concrete c) Hot water distribution d) none of the above

Last Answer : reinforced concrete

In the natural draft cooling tower_________ is not required a) Fan b) tower c) Nozzle d) none of the above

Description : In the natural draft cooling tower_________ is not required a) Fan b) tower c) Nozzle d) none of the above

Last Answer : Fan

In natural draft cooling tower the air flow is obtained by___________ a) Difference in air pressure b) difference in air temperature c) Difference in air speed d) none of the above

Description : In natural draft cooling tower the air flow is obtained by___________ a) Difference in air pressure b) difference in air temperature c) Difference in air speed d) none of the above

Last Answer : Difference in air pressure

Natural draft cooling tower are mainly used in a) Steel Industry b) Alumina industry c) Fertilizer industry d) Power station

Description : Natural draft cooling tower are mainly used in a) Steel Industry b) Alumina industry c) Fertilizer industry d) Power station

Last Answer : Power station

Natural draft in hyperbolic cooling tower is used for production of a) Fertilizer b) Steel c) Chemical d) Electrical energy

Description : Natural draft in hyperbolic cooling tower is used for production of a) Fertilizer b) Steel c) Chemical d) Electrical energy

Last Answer : d) Electrical energy

Design of hyperbolic cooling tower standard for all cooling tower a) Mechanical draft b) Natural draft c) Both a & b d) Neither a & b

Description : Design of hyperbolic cooling tower standard for all cooling tower a) Mechanical draft b) Natural draft c) Both a & b d) Neither a & b

Last Answer : b) Natural draft

Differentiate between natural draught and forced draught cooling tower.

Description : Differentiate between natural draught and forced draught cooling tower.

Last Answer : Sr. No. Natural draught Forced draught 1 The air flows naturally without fan through tower and provides required cooling Fan is located at the top of the tower and enters the ... from tower cannot be controlled. The temp. of water coming out from tower can be controlled.

Write the elements of forced draught cooling tower.

Description : Write the elements of forced draught cooling tower.

Last Answer : Following are the elements of forced draught cooling tower; a) Forced draught fan b) Eliminator c) Spray header d) Spray nozzle e) Circulating pump

The ……….-induced response of cooling tower is the key factor to improve safety and to reduce tower crack. a) wind c) heat b) water d) steam

Description : The ……….-induced response of cooling tower is the key factor to improve safety and to reduce tower crack. a) wind c) heat b) water d) steam

Last Answer : wind

Name The Coolants Commonly Used For Fast Breeder Reactors?

Description : Name The Coolants Commonly Used For Fast Breeder Reactors?

Last Answer :  Liquid metal (Na (or) Na K)  Helium (He)  Carbon dioxide.

What Is Breeding In Nuclear Reactor?

Description : What Is Breeding In Nuclear Reactor?

Last Answer : The process of producing fissionable material from a fertile material such as uranium 238 (U 238) and thorium 232 (Th 232) by neutron absorption is known as breeding.

Name The Different Components Of Nuclear Reactor?

Description : Name The Different Components Of Nuclear Reactor?

Last Answer : 1. Nuclear fuel 2. Moderator 3. Control rods 4. Reflectors 5. Reactor vessel 6. Biological shielding 7. Coolant