As compared to ordinary Portland cement, high alumina cement has (A) Higher initial setting time but lower final setting time (B) Lower initial setting time but higher final setting time (C) Higher initial and final setting times (D) Lower initial and final setting times

As compared to ordinary Portland cement, high alumina cement has
(A) Higher initial setting time but lower final setting time
(B) Lower initial setting time but higher final setting time
(C) Higher initial and final setting times
(D) Lower initial and final setting times
by

1 Answer

Answer :

Answer: Option A
by

Related questions

For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2

Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2

Last Answer : (C) Initial setting time is not less than 30 minutes

The initial setting time for ordinary Portland cement as per IS specifications should not be less than (A) 10 minutes (B) 30 minutes (C) 60 minutes (D) 600 minutes

Description : The initial setting time for ordinary Portland cement as per IS specifications should not be less than (A) 10 minutes (B) 30 minutes (C) 60 minutes (D) 600 minutes

Last Answer : Answer: Option B

According to IS Code , the requirement of an ordinary Portland cement is (a) The residue does not exceed 10% when sieved through is sieve no .9 (b) Its initial setting time is not less than 30 minutes. (c) its expansion is not morethan 10mm for unaerated cement (d) All the above.

Description : According to IS Code , the requirement of an ordinary Portland cement is (a) The residue does not exceed 10% when sieved through is sieve no .9 (b) Its initial setting time is not less than 30 minutes. (c) its expansion is not morethan 10mm for unaerated cement (d) All the above.

Last Answer : (d) All the above.

As per IS specifications, the maximum final setting time for ordinary Portland cement should be (A) 30 minutes (B) 1 hour (C) 6 hours (D) 10 hour

Description : As per IS specifications, the maximum final setting time for ordinary Portland cement should be (A) 30 minutes (B) 1 hour (C) 6 hours (D) 10 hour

Last Answer : Answer: Option D

Which of the following cements is expected to have the highest compressive strength after 3 days (a) Ordinary Portland cement (b) Rapid hardening cement (c) High alumina cement (d) Sulphate resisting cement.

Description : Which of the following cements is expected to have the highest compressive strength after 3 days (a) Ordinary Portland cement (b) Rapid hardening cement (c) High alumina cement (d) Sulphate resisting cement.

Last Answer : (c) High alumina cement

Chief constituent of ordinary Portland cement is [ A ] Lime [ B ] Alumina [ C ] Magnesia [ D ] Iron oxide

Description : Chief constituent of ordinary Portland cement is [ A ] Lime [ B ] Alumina [ C ] Magnesia [ D ] Iron oxide

Last Answer : [ A ] Lime

As compared to ordinary Portland cement, use of pozzolana cement (A) Reduces workability (B) Increases bleeding (C) Increases shrinkage (D) Increases strength

Description : As compared to ordinary Portland cement, use of pozzolana cement (A) Reduces workability (B) Increases bleeding (C) Increases shrinkage (D) Increases strength

Last Answer : Answer: Option C

When compared to ordinary Portland cement, Rapid hardening Portland cement contains ______________ amount of lime content [ A ] Equal [ B ] Greater [ C ] Lesser [ D ] Zero

Description : When compared to ordinary Portland cement, Rapid hardening Portland cement contains ______________ amount of lime content [ A ] Equal [ B ] Greater [ C ] Lesser [ D ] Zero

Last Answer : [ B ] Greater

The cement whose strength is a little lower than the ordinary cement during the first three months but attains afterwards the same strength, is known as (A) Low-heat Portland cement (B) Rapid hardening Portland cement (C) Portland blast slag cement (D) Portland pozzolana cement

Description : The cement whose strength is a little lower than the ordinary cement during the first three months but attains afterwards the same strength, is known as (A) Low-heat Portland cement (B) Rapid hardening Portland cement (C) Portland blast slag cement (D) Portland pozzolana cement

Last Answer : Answer: Option A

Pick out the wrong statement. (A) High early strength cement are made from materials having high silica to lime ratio (B) The function of gypsum in cement is to enhance its initial setting rate (C) Acid resistant cements are known as silicate cement (D) Major component of greyish Portland cement is tricalcium silicate

Description : Pick out the wrong statement. (A) High early strength cement are made from materials having high silica to lime ratio (B) The function of gypsum in cement is to enhance its initial ... cements are known as silicate cement (D) Major component of greyish Portland cement is tricalcium silicate

Last Answer : (A) High early strength cement are made from materials having high silica to lime ratio

The main ingredients of Portland cement are (A) Lime and silica (B) Lime and alumina (C) Silica and alumina (D) Lime and iron

Description : The main ingredients of Portland cement are (A) Lime and silica (B) Lime and alumina (C) Silica and alumina (D) Lime and iron

Last Answer : Answer: Option A

The proportion of lime, silica, alumina and iron oxide in a Portland cement is (a) 63:22:6:3 (b) 63:22:3:6 (c) 22:63:6:3 (d) All the above

Description : The proportion of lime, silica, alumina and iron oxide in a Portland cement is (a) 63:22:6:3 (b) 63:22:3:6 (c) 22:63:6:3 (d) All the above

Last Answer : (a) 63:22:6:3

Pick up the correct statement regarding low heat cement from the following: (A) It possesses less compressive strength (B) Its initial setting time is about one hour (C) Its final setting time is about 10 hours (D) All the above

Description : Pick up the correct statement regarding low heat cement from the following: (A) It possesses less compressive strength (B) Its initial setting time is about one hour (C) Its final setting time is about 10 hours (D) All the above

Last Answer : Answer: Option D

Portland pozzolana cement possesses (A) Higher resistance to chemical attack (B) Lower heat of hydration (C) Lower shrinkage on drying (D) All the above

Description : Portland pozzolana cement possesses (A) Higher resistance to chemical attack (B) Lower heat of hydration (C) Lower shrinkage on drying (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The lime in excess makes the cement unsound and causes the cement to expand and disintegrate (B) The silica in excess makes the cement stronger but its setting time also increases (C) The excess amount of alumina weakens the cement (D) All the above

Description : Pick up the correct statement from the following: (A) The lime in excess makes the cement unsound and causes the cement to expand and disintegrate (B) The silica in excess makes the cement stronger ... time also increases (C) The excess amount of alumina weakens the cement (D) All the above

Last Answer : Answer: Option D

Newly constructed pavement with ordinary Portland cement attains its working strength after (A) 7 days (B) 14 days (C) 21 days (D) 28 days

Description : Newly constructed pavement with ordinary Portland cement attains its working strength after (A) 7 days (B) 14 days (C) 21 days (D) 28 days

Last Answer : Answer: Option D

An ordinary Portland cement when tested for its fineness, should not leave any residue on I.S. sieve No. 9, more than (A) 5 % (B) 10 % (C) 15 % (D) 20 %

Description : An ordinary Portland cement when tested for its fineness, should not leave any residue on I.S. sieve No. 9, more than (A) 5 % (B) 10 % (C) 15 % (D) 20 %

Last Answer : (B) 10 %

Ordinary Portland cement is manufactured from (A) Lime stone and clay (B) Gypsum and lime (C) Pozzolana (D) Lime, pozzolana and clay

Description : Ordinary Portland cement is manufactured from (A) Lime stone and clay (B) Gypsum and lime (C) Pozzolana (D) Lime, pozzolana and clay

Last Answer : Answer: Option B

You are asked to construct a massive dam, the type of cement you will use, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Description : You are asked to construct a massive dam, the type of cement you will use, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Last Answer : Answer: Option C

For the construction of thin R.C.C. structures, the type of cement to be avoided, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Description : For the construction of thin R.C.C. structures, the type of cement to be avoided, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Last Answer : Answer: Option D

For road pavements, the cement generally used, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Description : For road pavements, the cement generally used, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Last Answer : Answer: Option B

The normal consistency of ordinary Portland cement is about (A) 10 % (B) 20 % (C) 30 % (D) 40 %

Description : The normal consistency of ordinary Portland cement is about (A) 10 % (B) 20 % (C) 30 % (D) 40 %

Last Answer : Answer: Option C

Addition of pozzolana to ordinary Portland cement increases (A) Bleeding (B) Shrinkage (C) Permeability (D) Heat of hydration

Description : Addition of pozzolana to ordinary Portland cement increases (A) Bleeding (B) Shrinkage (C) Permeability (D) Heat of hydration

Last Answer : Answer: Option B

Which of the following cements is suitable for use in massive concrete structures such as large dams? (A) Ordinary Portland cement (B) Low heat cement (C) Rapid hardening cement (D) Sulphate resisting cement

Description : Which of the following cements is suitable for use in massive concrete structures such as large dams? (A) Ordinary Portland cement (B) Low heat cement (C) Rapid hardening cement (D) Sulphate resisting cement

Last Answer : Answer: Option B

According to IS specifications, the compressive strength of ordinary Portland cement after three days should not be less than (A) 7 MPa (B) 11.5 MPa (C) 16 MPa (D) 21 MPa

Description : According to IS specifications, the compressive strength of ordinary Portland cement after three days should not be less than (A) 7 MPa (B) 11.5 MPa (C) 16 MPa (D) 21 MPa

Last Answer : Answer: Option C

Which of the following cements contains maximum percentage of dicalcium silicate? (A) Ordinary Portland cement (B) Low heat cement (C) Rapid hardening cement (D) Sulphate resisting cement

Description : Which of the following cements contains maximum percentage of dicalcium silicate? (A) Ordinary Portland cement (B) Low heat cement (C) Rapid hardening cement (D) Sulphate resisting cement

Last Answer : Answer: Option B

The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Description : The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Last Answer : (b) 17.5 N/mm2

For Ordinary Portland cement concrete exposed to dry and hot weather conditions, good moist curing period is [ A ] 7 days [ B ] 10 days [ C ] 14 days [ D ] None of the above

Description : For Ordinary Portland cement concrete exposed to dry and hot weather conditions, good moist curing period is [ A ] 7 days [ B ] 10 days [ C ] 14 days [ D ] None of the above

Last Answer : [ B ] 10 days

Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2

Description : Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2

Last Answer : [ B ] 11.5 N/mm2

For mass concrete work, the type of cement preferable is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Description : For mass concrete work, the type of cement preferable is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Last Answer : [ C ] Low heat cement

For road pavements, the cement generally used, is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Description : For road pavements, the cement generally used, is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Last Answer : [ A ] Ordinary Portland cement

Ordinary Portland cement requires a specific surface of [ A ] 1250 cm2/gm [ B ] 2250 cm 2/gm [ C ] 3250 cm 2/gm [ D ] 3500 cm 2/gm

Description : Ordinary Portland cement requires a specific surface of [ A ] 1250 cm2/gm [ B ] 2250 cm 2/gm [ C ] 3250 cm 2/gm [ D ] 3500 cm 2/gm

Last Answer : [ B ] 2250 cm 2/gm

Low heat cement contains more amount of __________ than that of ordinary Portland cement [ A ] C3S [ B ] C2S [ C ] C3A [ D ] None of the above

Description : Low heat cement contains more amount of __________ than that of ordinary Portland cement [ A ] C3S [ B ] C2S [ C ] C3A [ D ] None of the above

Last Answer : [ B ] C2S

Portland cement manufactured from pure white chalk and clay but free from iron-oxide, is known as (A) Quick setting cement (B) Rapid hardening cement (C) White cement (D) Low heat Portland cement

Description : Portland cement manufactured from pure white chalk and clay but free from iron-oxide, is known as (A) Quick setting cement (B) Rapid hardening cement (C) White cement (D) Low heat Portland cement

Last Answer : Answer: Option C

Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is (A) 5CaO. 3 Al2O3 (B) 3CaO. Al2O3 (C) 3CaO. SiO2 (D) 2CaO. SiO2

Description : Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is (A) 5CaO. 3 Al2O3 (B) 3CaO. Al2O3 (C) 3CaO. SiO2 (D) 2CaO. SiO2

Last Answer : Option A

The main ingredients of Portland cement are a) Lime and silica* b) Lime and Alumina c) Alumina magnesia d) Silica and Alumina

Description : The main ingredients of Portland cement are a) Lime and silica* b) Lime and Alumina c) Alumina magnesia d) Silica and Alumina

Last Answer : a) Lime and silica*

Explain the method to determine initial and final setting time of cement.

Description : Explain the method to determine initial and final setting time of cement.

Last Answer : Procedure: i. Take 400 gm. of cement sample and add 0.85 times water required for its standard consistency to prepare homogenous cement paste. Note down the time at which water is added to cement as T1 min. ... a cement surface as T3 min. viii. Calculate final setting time i.e. FST = T3-T1 min.

For quality control of Portland cement, the test essentially done is (A) Setting time (B) Tensile strength (C) Consistency (D) All the above

Description : For quality control of Portland cement, the test essentially done is (A) Setting time (B) Tensile strength (C) Consistency (D) All the above

Last Answer : D

For construction of structures in sea water, the cement generally preferred to, is (A) Portland-pozzolana cement (B) Quick setting cement (C) Low heat Portland cement (D) Rapid hardening cement

Description : For construction of structures in sea water, the cement generally preferred to, is (A) Portland-pozzolana cement (B) Quick setting cement (C) Low heat Portland cement (D) Rapid hardening cement

Last Answer : Answer: Option A

Which type of following cement is used for mass concrete work a) High Alumina cement b) Quick setting cement c) Rapid hardening cement d) Low heat cement*

Description : Which type of following cement is used for mass concrete work a) High Alumina cement b) Quick setting cement c) Rapid hardening cement d) Low heat cement*

Last Answer : d) Low heat cement*

The gypsum is added to the cement for (a) Providing high strength to the cement (b) Controlling the initial setting time of cement. (c) Lowering the clinkering temp of cement (d) All the above.

Description : The gypsum is added to the cement for (a) Providing high strength to the cement (b) Controlling the initial setting time of cement. (c) Lowering the clinkering temp of cement (d) All the above.

Last Answer : (b) Controlling the initial setting time of cement.

Formation of ordinary Portland cement?

Description : Formation of ordinary Portland cement?

Last Answer : Ordinary Portland cement is form from materials of limestone or chalk and clay in proportion of 78and 22% respectively. The limestone and the clay are crushed and water is added to form slurry. The ... powder and a range of gypsum is added which generate setting or hardening when water is added.

List four major compounds of cement with their percentage in ordinary Portland cement.

Description : List four major compounds of cement with their percentage in ordinary Portland cement.

Last Answer : List four major compounds of cement with their percentage in ordinary Portland cement.

Pick out the wrong statement. (A) Dry process is used for the manufacture of cement, when the raw material is blast furnace slag (B) Portland cement is made employing wet process (C) Gypsum is added to Portland cement to lengthen its setting time (D) None of these

Description : Pick out the wrong statement. (A) Dry process is used for the manufacture of cement, when the raw material is blast furnace slag (B) Portland cement is made employing wet process (C) Gypsum is added to Portland cement to lengthen its setting time (D) None of these

Last Answer : (D) None of these

(3) preventing rapid setting of cement Explanation: Portland cement clinker is a hydraulic material which shall consist of at least two-thirds by mass of calcium silicates, the remainder consisting of aluminium- and ironcontaining clinker phases and other compounds. The ratio of CaO to SiO2 shall not be less than 2.0. The magnesium oxide content (MgO) shall not exceed 5.0% by mass. Cement sets when mixed with water by way of a complex series of chemical reactions still only partly understood.

Description : (3) preventing rapid setting of cement Explanation: Portland cement clinker is a hydraulic material which shall consist of at least two-thirds by mass of calcium silicates, the remainder consisting of ... mixed with water by way of a complex series of chemical reactions still only partly understood.

Last Answer : Milk is a colloidal system in which: (1) Water is dispersed in fat (2) Fat is dispersed in water (3) Fat and water are dispersed in each other (4) Fat is dissolved

The addition of gypsum to portland cement helps in : (1) increasing the strength of cement (2) rapid setting of cement (3) preventing rapid setting of cement (4) reduction in the cost of cement

Description : The addition of gypsum to portland cement helps in : (1) increasing the strength of cement (2) rapid setting of cement (3) preventing rapid setting of cement (4) reduction in the cost of cement

Last Answer : preventing rapid setting of cement

To retard the initial setting time of cement, the compound responsible, is (A) Tri-calcium silicate (B) Gypsum (C) Di-calcium silicate (D) Tri-calcium aluminate

Description : To retard the initial setting time of cement, the compound responsible, is (A) Tri-calcium silicate (B) Gypsum (C) Di-calcium silicate (D) Tri-calcium aluminate

Last Answer : Answer: Option B

Initial setting time of cement for asbestos cement products should be not less than (A) 30 minutes (B) 50 minutes (C) 75 minutes (D) 90 minutes

Description : Initial setting time of cement for asbestos cement products should be not less than (A) 30 minutes (B) 50 minutes (C) 75 minutes (D) 90 minutes

Last Answer : Answer: Option D

The basic purpose of a retarder in concrete is (A) To increase the initial setting time of cement paste in concrete (B) To decrease the initial setting time of cement paste in concrete (C) To render the concrete more water tight (D) To improve the workability of concrete mix

Description : The basic purpose of a retarder in concrete is (A) To increase the initial setting time of cement paste in concrete (B) To decrease the initial setting time of cement paste in concrete (C) To render the concrete more water tight (D) To improve the workability of concrete mix

Last Answer : Answer: Option A

If ‘W’ is the percentage of water required for normal consistency of cement, water to be added for determination of initial setting time is (a) 0.50 W (b) 0.62 W (c) 0.75 W (d) 0.85 W

Description : If ‘W’ is the percentage of water required for normal consistency of cement, water to be added for determination of initial setting time is (a) 0.50 W (b) 0.62 W (c) 0.75 W (d) 0.85 W

Last Answer : (d) 0.85 W