The moments developed in the slab are influenced by the following factors i.Short span ii.Long span iii.Type of supporting edge. iv.Magnitude and type of load on slab [ A ] i, iii and iv [ B ] ii ,iii and iv [ C ] i and iii [ D ] i, ii , iii and iv

The moments developed in the slab are influenced by the following factors
i.Short span
ii.Long span
iii.Type of supporting edge.
iv.Magnitude and type of load on slab
[ A ] i, iii and iv
[ B ] ii ,iii and iv
[ C ] i and iii
[ D ] i, ii , iii and iv
by

1 Answer

Answer :

[ D ] i, ii , iii and iv
by

Related questions

Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Description : Negative yield line form i. Near the supports in the case of slabs fixed or continuous at the edge. ii. At mid span in the case of slabs fixed. iii.At mid span for simply supported circular slab [ A ] i [ B ] i and ii [ C ] i and iii [ D ] i, ii and iii

Last Answer : [ A ] i

If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured parallel to the supported edge, the effective width of the slab be is (A) K/x (1 + x/d) + bw (B) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Description : If K is a constant depending upon the ratio of the width of the slab to its effective span l, x is the distance of the concentrated load from the nearer support, bw is the width of the area of contact of the concentrated load measured ... ) Kx (1 - x/l) + bw (C) Kx (1 + x/l) + bw (D) All the above

Last Answer : Answer: Option B

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C

In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : In a ring beam subjected to uniformly distributed load (i) Shear force at mid span is zero (ii) Shear force at mid span is maximum (iii) Torsion at mid span is zero (iv) Torsion at mid span is maximum The correct answer ... and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Option A

The slab is designed as one way if the ratio of long span to short span is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2 (D) Greater than 2

Description : The slab is designed as one way if the ratio of long span to short span is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2 (D) Greater than 2

Last Answer : Answer: Option D

When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.

Last Answer : (d) Two-way slab.

In a two way slab flexural bending develops [ A ] Along short span [ B ] Along long span [ C ] In Mutually perpendicular directions [ D ] At the center of short span

Description : In a two way slab flexural bending develops [ A ] Along short span [ B ] Along long span [ C ] In Mutually perpendicular directions [ D ] At the center of short span

Last Answer : [ C ] In Mutually perpendicular directions

In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed as a cantilever The correct answer is (A) (i) and (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Description : In counterfort type retaining walls (i) The vertical slab is designed as a continuous slab (ii) The heel slab is designed as a continuous slab (iii) The vertical slab is designed as a cantilever (iv) The heel slab is designed ... (ii) (B) (i)and(iv) (C) (ii) and (iii) (D) (iii) and (iv)

Last Answer : Answer: Option A

If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than (A) WL/12 (L - 2D/3)² (B) WL/10 (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Description : If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span ... (L + 2D/3)² (C) WL/10 (L - 2D/3)² (D) WL/12 (L - D/3)²

Last Answer : Answer: Option C

When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Description : When load is applied on concrete pavement (A) Away from edges, the maximum bending moment is negative (B) Away from edges, the maximum bending moment cause compression (C) On the edges, the maximum stress is parallel to the edge of the slab (D) None of these

Last Answer : Answer: Option C

A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held down and carrying uniformly distributed load. (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.

Description : A two way slab (a) May be simply supported on the four edges, with comers not held down and carrying uniformly distributed load. (b) May be simply supported on the four edge , with corners held ... . (c) May have edges fixed or continuous and carrying uniformly distributed load. (d) All the above.

Last Answer : (d) All the above.

Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to resist a sagging bending moment near mid-span. (c) When the slab is built into a brick or masonry wall the slab should be designed to resist a hogging moment at the face of the support. (d) All of the above.

Description : Find the correct statement from the followings. (a) For a cantilever slab, the ratio of span to overall depth should not 12. (b) One way slab which carry uniformly distributed load should be designed to ... be designed to resist a hogging moment at the face of the support. (d) All of the above.

Last Answer : (d) All of the above.

Compare pin type and suspension insulators on given points: (i) Position of insulator on cross arm. (ii) Position of conductor on insulator. (iii) Reaction on cross arm. (iv) Possibility of flash over due to large birds (v) Maintenance/Replacement cost (vi) Maximum voltage level (vii) Effect on height of supporting structure. (viii) Life

Description : Compare pin type and suspension insulators on given points: (i) Position of insulator on cross arm. (ii) Position of conductor on insulator. (iii) Reaction on cross arm. (iv) Possibility of ... Replacement cost (vi) Maximum voltage level (vii) Effect on height of supporting structure. (viii) Life 

Last Answer : S.No  Points Pin Type insulator Suspension or Disc Type insulator 1 Position of insulator on cross arm It is fixed on top of cross arm by using galvanized steel pin. So it is ... so to maintain minimum ground clearance height of pole increase.  8 Life Less More

Sinking of an intermediate support of a continuous beam (i) Reduces the negative moment at support (ii) Increases the negative moment at support (iii) Reduces the positive moment at center of span (iv) Increases the positive moment at center of span The correct answer is (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Description : Sinking of an intermediate support of a continuous beam (i) Reduces the negative moment at support (ii) Increases the negative moment at support (iii) Reduces the positive moment at center of span (iv) Increases the positive moment ... (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv)

Last Answer : Answer: Option B

In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top face near centre of span The correct answer is (A) Only (i) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Description : In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top ... ) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)

Last Answer : Answer: Option C

By applying the static equations i.e. H V M = 0, to a determinate structure, we may determine (A) Supporting reactions only (B) Shear forces only (C) Bending moments only (D) All the above

Description : By applying the static equations i.e. H V M = 0, to a determinate structure, we may  determine  (A) Supporting reactions only  (B) Shear forces only  (C) Bending moments only  (D) All the above

Last Answer : (D) All the above

Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Description : Thickened part of a flat slab over its supporting column, is technically known as (A) Drop panel (B) Capital (C) Column head (D) None of these

Last Answer : Answer: Option A

Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Description : Enlarged head of a supporting column of a flat slab is technically known as (A) Supporting end of the column (B) Top of the column (C) Capital (D) Drop panel

Last Answer : Answer: Option C

A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Description : A reinforcing slab, build monolithically with the supporting columns and is reinforced in two or more directions, without any provision of beams is called a (a) Two way slab (b) Flat slab (c) Continus slab (d) Cireulashion

Last Answer : (b) Flat slab

For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1

Description : For a slab supported on its four edges with corners held down and loaded uniformly, the Marcus correction factor to the moments obtained by Grashoff Rankine's theory (A) Is always less than 1 (B) Is always greater than 1 (C) Can be more than 1 (D) Can be less than 1

Last Answer : Answer: Option A

If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) w1/w2 = l2/l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Last Answer : Answer: Option D

Long and short spans of a two way slab are ly and lx and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. According to Rankine Grashoff theory (A) (wx /wy ) = (ly /lx ) (B) (wx/wy) = (ly/lx)² (C) (wx /wy ) = (ly /lx )4 (D) None of these

Description : Long and short spans of a two way slab are ly and lx and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. According to Rankine Grashoff theory (A) (wx /wy ) = (ly /lx ) (B) (wx/wy) = (ly/lx)² (C) (wx /wy ) = (ly /lx )4 (D) None of these

Last Answer : Answer: Option C

Finished tolerance on 10 cm. long st. edge on surface of head shall be? (i) 0 to 0.1 mm (ii) 0 to 0.2 mm (iii) 0 to 0.4 mm* (iv) 0 to 0.3 mm

Description : Finished tolerance on 10 cm. long st. edge on surface of head shall be? (i) 0 to 0.1 mm (ii) 0 to 0.2 mm (iii) 0 to 0.4 mm* (iv) 0 to 0.3 mm

Last Answer : (iii) 0 to 0.4 mm*

Finished tolerance on 10 cm long st. edge at the centre on gauge side shall be? (i) ± 0.4 mm (ii) ± 0.1 mm (iii) ± 0.2 mm (iv) ± 0.3 mm*

Description : Finished tolerance on 10 cm long st. edge at the centre on gauge side shall be? (i) ± 0.4 mm (ii) ± 0.1 mm (iii) ± 0.2 mm (iv) ± 0.3 mm*

Last Answer : iv) ± 0.3 mm*

Finished tolerance on 1 Mt. long st. edge on surface of head shall be? (i) 0 to .1 mm (ii) 1 to 1.5 mm (iii) 0 mm (iv) 0 to 1 mm*

Description : Finished tolerance on 1 Mt. long st. edge on surface of head shall be? (i) 0 to .1 mm (ii) 1 to 1.5 mm (iii) 0 mm (iv) 0 to 1 mm*

Last Answer : (iv) 0 to 1 mm*

While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia(D) None of the above

Description : While using three moments equation, a fixed end of a continuous beam is replaced by an additional span of (A) Zero length (B) Infinite length (C) Zero moment of inertia (D) None of the above

Last Answer : (A) Zero length

The three moments equation is applicable only when (A) The beam is prismatic (B) There is no settlement of supports (C) There is no discontinuity such as hinges within the span (D) The spans are equal

Description : The three moments equation is applicable only when (A) The beam is prismatic (B) There is no settlement of supports (C) There is no discontinuity such as hinges within the span (D) The spans are equal

Last Answer : (C) There is no discontinuity such as hinges within the span

The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Description : The name of the welded joint made by placing the plates edge to edge is (i) Fillet welded joint (ii) Butt welded joint (iii) Fillet-Butt welded joint (iv) None

Last Answer : (ii) Butt welded joint

Choose the option that lists the set of statements that are NOT TRUE according to the poem. I. The tiger is in quiet rage because he has been imprisoned. II. A tiger is caged and kept in the zoo. III. He criticises the brilliant stars from behind the bars. 1V. The poet alternates between the description of a caged tiger and a tiger in jungle. V. Tiger shouldn‘t have been prowling at the jungle‘s edge. (a) II & V (b) I, IV & V (c) I, II & III (d) III & V

Description : Choose the option that lists the set of statements that are NOT TRUE according to the poem. I. The tiger is in quiet rage because he has been imprisoned. II. A tiger is caged and kept in the zoo. III. He criticises the brilliant stars ... edge. (a) II & V (b) I, IV & V (c) I, II & III (d) III & V

Last Answer : (d) III & V

Finished tolerance on 1 Mt. st. edge at the centre on gauge side shall be? (i) ± 0.2 mm (ii) ± 0.3 mm (iii) ± 0.5 mm* (iv) ± 1.0 mm

Description : Finished tolerance on 1 Mt. st. edge at the centre on gauge side shall be? (i) ± 0.2 mm (ii) ± 0.3 mm (iii) ± 0.5 mm* (iv) ± 1.0 mm

Last Answer : (iii) ± 0.5 mm*

Finishing tolerances are measured by? (i) On 30 cm scale (ii) 1 MT straightedge or 10 CM straightedge.* (iii) On 15 cm straight edge (iv) On 30 cm straight edge

Description : Finishing tolerances are measured by? (i) On 30 cm scale (ii) 1 MT straightedge or 10 CM straightedge.* (iii) On 15 cm straight edge (iv) On 30 cm straight edge

Last Answer : (ii) 1 MT straightedge or 10 CM straightedge.*

In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Description : In new Rail as well as second hand rails how much end bends of the rails in vertical are permitted when checked with one meter straight edge before welding? (i) +0.5mm, -0 mm in vertical * (ii) +0.2mm, -.3 mm in vertical (iii) +0.3mm, -2 mm in vertical (iv) 0 mm, +.5 mm in vertical

Last Answer : (i) +0.5mm, -0 mm in vertical *

Define following terms: i) Economic span ii) Afflux iii) Waterway iv) Free board

Description : Define following terms: i) Economic span ii) Afflux iii) Waterway iv) Free board

Last Answer : i) Economic span: The span for which the total cost of the bridge is minimum is known as economical span of a bridge. ii) Afflux: It is the rise in water surface caused due to the obstruction ... , if any, and the lowest point on the underside of the bridge super structure is called free board.

The maximum ratio of span to depth of a cantilever slab, is (A) 8 (B) 10 (C) 12 (D) 16

Description : The maximum ratio of span to depth of a cantilever slab, is (A) 8 (B) 10 (C) 12 (D) 16

Last Answer : Answer: Option C

The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Description : The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Last Answer : Answer: Option D

The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Last Answer : Answer: Option B

For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Description : For a continuous floor slab supported on beams, the ratio of end span length and intermediate span length, is (A) 0.6 (B) 0.7 (C) 0.8 (D) 0.9

Last Answer : Answer: Option D

If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Description : The maximum ratio of span to depth of a slab simply supported and spanning in two directions, is (A) 25 (B) 30 (C) 35 (D) 40

Last Answer : Answer: Option C

If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Description : If the length of an intermediate span of a continuous slab is 5m, the length of the end span is kept (A) 4.5 m (B) 4.0 m (C) 3.5 m (D) 3.0 m

Last Answer : Answer: Option A

Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of the column (C) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Last Answer : Answer: Option C

In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span

Description : In a simply supported slab, alternate bars are curtailed at (A) 1/4th of the span (B) 1/5th of the span (C) 1/6th of the span (D) 1/7th of the span

Last Answer : Answer: Option D

The neutral axis of a T-beam exists (A) Within the flange (B) At the bottom edge of the slab (C) Below the slab (D) All the above

Description : The neutral axis of a T-beam exists (A) Within the flange (B) At the bottom edge of the slab (C) Below the slab (D) All the above

Last Answer : Answer: Option D

The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Description : The width of the flange of a L-beam, should be less than (A) One-sixth of the effective span (B) Breadth of the rib + four times thickness of the slab (C) Breadth of the rib + half clear distance between ribs (D) Least of the above

Last Answer : Answer: Option D

The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20

Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction, is (A) 35 (B) 25 (C) 30 (D) 20

Last Answer : Answer: Option C

The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Description : The diameter of the column head support a flat slab, is generally kept (A) 0.25 times the span length (B) 0.25 times the diameter of the column (C) 4.0 cm larger than the diameter of the column (D) 5.0 cm larger than the diameter of the column

Last Answer : Option A

The maximum ratio of span to depth of a cantilever slab is (a) 8 (b) 10 (c) 12 (d) 14

Description : The maximum ratio of span to depth of a cantilever slab is (a) 8 (b) 10 (c) 12 (d) 14

Last Answer : (c) 12

The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Description : The maximum ratio of span to depth of a slab simple supported and spanning in two directions, is (a) 25 (b) 30 (c) 35 (d) 40

Last Answer : (c) 35

The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20

Description : The maximum ratio of span to depth of a slab simply supported and spanning in one direction is (a) 35 (b) 25 (c) 30 (d) 20

Last Answer : (c) 30