The leakage current must not be more than ____________ of maximum supply current

The leakage current must not be more than ____________ of maximum supply current
by

1 Answer

Answer :

The leakage current must not be more than 1 / 5000 of maximum supply current

by

Related questions

When a megohmmeter is used to test the insulation of a large motor, the initial dip of the pointer toward 'zero' is caused by ____________. A. good insulation B. the capacitance of the windings C. the leakage of the current along the surface of dirty insulation D. the dielectric-absorption effect of the insulation

Description : When a megohmmeter is used to test the insulation of a large motor, the initial dip of the pointer toward 'zero' is caused by ____________. A. good insulation B. the capacitance of the ... of the current along the surface of dirty insulation D. the dielectric-absorption effect of the insulation

Last Answer : Answer: B

When using a megohmmeter to test the dielectric strength of wire insulation, a continuous series of slight downscale kicks by the pointer is result of ____________. A. good insulation B. the leakage of current along the surface of dirty insulation C. the capacitance of the windings D. the dielectric-absorption effect of the insulation

Description : When using a megohmmeter to test the dielectric strength of wire insulation, a continuous series of slight downscale kicks by the pointer is result of ____________. A. good insulation B. the ... dirty insulation C. the capacitance of the windings D. the dielectric-absorption effect of the insulation

Last Answer : Answer: B

You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, becoming fairly steady as the leakage current stabilizes B. remain constant as the temperature of the windings increases C. continue to drop as the potential is maintained, becoming fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Description : You are testing the insulation in an AC generator with a megohmeter. The resistance value of a dry, clean winding will ____________. A. continue to rise as the test potential is maintained, ... fairly steady after 5 to 7 minutes D. stabilize after approximately 2 to 4 minutes of fluctuation

Last Answer : Answer: A

When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Description : When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Last Answer : Answer: B

Describe the procedure to locate leakage in Compressed Natural Gas Fuel supply system of a car. State relevant precaution.

Description : Describe the procedure to locate leakage in Compressed Natural Gas Fuel supply system of a car. State relevant precaution.

Last Answer : Procedure to locate Leakage in Compressed Natural Gas Fuel Supply System of a Car: 1. The first indicator is the foul smelling agent present in CNG.. 2. The second level of test you can do is to take a ... , incense sticks, etc. 2. Close the CNG regulator and 3. Put the safety cap on the cylinder.

When applying to pressure ratings listed in ASME B16.5 at high or low temperatures which of the following must be considered? a) Risk of leakage due to forces and moments developed. b) Bursting of the flanged fitting. c) The bolting forces at the flange. d) All of the above.

Description : When applying to pressure ratings listed in ASME B16.5 at high or low temperatures which of the following must be considered? a) Risk of leakage due to forces and moments developed. b) Bursting of the flanged fitting. c) The bolting forces at the flange. d) All of the above.

Last Answer : a) Risk of leakage due to forces and moments developed.

The maximum pressure which the pipe can withstand without any leakage during hydrostatic pressure test, is called (A) Working pressure (B) Design pressure (C) Test pressure (D) Hydrostatic pressure

Description : The maximum pressure which the pipe can withstand without any leakage during hydrostatic pressure test, is called (A) Working pressure (B) Design pressure (C) Test pressure (D) Hydrostatic pressure

Last Answer : (C) Test pressure

The leakage current in the transmission lines is referred to as the a) Resistance b) Radiation c) Conductance d) Polarisation

Description : The leakage current in the transmission lines is referred to as the a) Resistance b) Radiation c) Conductance d) Polarisation

Last Answer : Ans: C

An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage

Description : An electrical connection between the wiring of an electric motor and its metal frame is known as a/an _____________. A. eddy current B. ground C. impedance D. flux leakage

Last Answer : Answer: B

One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Description : One of the generator or motor bearings is generally insulated from the end housing in order to prevent ________. A. rapid brush wear B. current leakage from the shaft C. excessive field winding heat D. circulation of shaft currents induced in the machine's frame

Last Answer : Answer: D

When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter pointer _____________. A. fluctuating around a constant resistance reading B. dipping towards 'zero', then rising slowly C. kicking slightly downscale as voltage is applied D. continually rising as the test voltage is applied

Description : When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter pointer _____________. A. fluctuating around a ... slightly downscale as voltage is applied D. continually rising as the test voltage is applied

Last Answer : Answer: C

When a megohmmeter is used to test the dielectric strength of wire insulation, the initial dip of the pointer toward 'zero' is caused by _____________. A. good insulation B. the leakage of current along the surface of dirty insulation C. the capacitance of the circuit D. the dielectric absorption effect of the insulation

Description : When a megohmmeter is used to test the dielectric strength of wire insulation, the initial dip of the pointer toward 'zero' is caused by _____________. A. good insulation B. the leakage of ... of dirty insulation C. the capacitance of the circuit D. the dielectric absorption effect of the insulation

Last Answer : Answer: C

When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter's pointer _____________. A. dipping toward zero then raising slowly B. continually rising as test voltage is applied C. kicking slightly down scale as voltage is applied D. fluctuating around a constant resistance reading

Description : When a megohmmeter is being used to test insulation resistance, current leakage along the surface of the insulation is indicated by the megohmmeter's pointer _____________. A. dipping toward ... kicking slightly down scale as voltage is applied D. fluctuating around a constant resistance reading

Last Answer : Answer: C

When a megohmmeter is used to test insulation, the gradual rise of the pointer reading as a result of continued cranking, is caused by _____________. A. good conductor resistance B. the leakage of current along the surface of dirty insulation C. the inductive reactance of the windings D. the dielectric-absorption effect of the insulation

Description : When a megohmmeter is used to test insulation, the gradual rise of the pointer reading as a result of continued cranking, is caused by _____________. A. good conductor resistance B. the ... insulation C. the inductive reactance of the windings D. the dielectric-absorption effect of the insulation

Last Answer : Answer: D

The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Last Answer : Answer: A

How do you measure the leakage current in a house wiring?

Description : How do you measure the leakage current in a house wiring?

Last Answer : There are two ways for it. First one is to keep all lights and other domestic electric appliances OFF for an hour and record the energy consumption in the energy meter. Calculate current from it. Second way is by measuring the current in the house earth conductor as leakage current goes to earth.

What is the purpose of HV / leakage current test on stator?

Description : What is the purpose of HV / leakage current test on stator?  

Last Answer : This is to find out weakness in the stator winding. If the ambient conditions are right, and the insulation is weak, the leakage current will increase non-linearly.  The record of voltage ... current. In HV test starting leakage current should be more than switching off current in μ Amps. 

Insulators perform which of the following functions? a) Conduction b) Convection c) Provide electrical insulation d) Allows current leakage at interfaces

Description : Insulators perform which of the following functions? a) Conduction b) Convection c) Provide electrical insulation d) Allows current leakage at interfaces

Last Answer : c) Provide electrical insulation

The records of exports and imports in goods and services and transfer payments is known as a) Current account b) Budget surplus c) Economic leakage d) degree of openness

Description : The records of exports and imports in goods and services and transfer payments is known as a) Current account b) Budget surplus c) Economic leakage d) degree of openness

Last Answer : a) Current account

A cable carrying alternating current has (a) hysteresis losses only (b) hysteresis and leakage losses only (c) hysteresis, leakage and copper losses only (d) hysteresis, leakage, copper and friction losses

Description : A cable carrying alternating current has (a) hysteresis losses only (b) hysteresis and leakage losses only (c) hysteresis, leakage and copper losses only (d) hysteresis, leakage, copper and friction losses

Last Answer : (b) hysteresis and leakage losses only

In a reverse biased PN-junction, which current carriers cause leakage current?

Description : In a reverse biased PN-junction, which current carriers cause leakage current?

Last Answer : The minority carriers

Describe the leakage current in a transmission line and in what unit it is expressed.

Description : Describe the leakage current in a transmission line and in what unit it is expressed.

Last Answer : The small amount of current that flows through the dielectric between two wires of a transmission line and is expressed in micro ohms per unit length.

As a transistor ages, what happens to the leakage current?

Description : As a transistor ages, what happens to the leakage current?

Last Answer : It tends to increase

The leakage current that flows through a photodiode with no light input ∙ A. dark voltage ∙ B. dark impedance ∙ C. dark power ∙ D. dark current

Description : The leakage current that flows through a photodiode with no light input ∙ A. dark voltage ∙ B. dark impedance ∙ C. dark power ∙ D. dark current

Last Answer : D. dark current

Dark current in light detectors is caused by ∙ a. Thermally generated carriers in the diode ∙ b. The absence of light input ∙ c. Small leakage current ∙ d. Its imperfection

Description : Dark current in light detectors is caused by ∙ a. Thermally generated carriers in the diode ∙ b. The absence of light input ∙ c. Small leakage current ∙ d. Its imperfection

Last Answer : a. Thermally generated carriers in the diode

In a PIN diode, leakage current in the absence of light is called: a. baseline current b. zero-point current c. dark current d. E-H current

Description : In a PIN diode, leakage current in the absence of light is called: a. baseline current b. zero-point current c. dark current d. E-H current

Last Answer : c. dark current

Silicon transistors are preferred because: (a) High operating temperature (b) Low leakage current (c) Suited to high frequency circuits (d) All

Description : Silicon transistors are preferred because: (a) High operating temperature (b) Low leakage current (c) Suited to high frequency circuits (d) All

Last Answer : (d) All

27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Description : 27] In a transformer, the leakage flux of each winding is proportional to the current in that winding because A. Ohm's law applies to magnetic circuits B. Leakage paths do no saturate C. the two windings are electrically isolated D. mutual flux is confined to the core

Last Answer : B. Leakage path do not saturate

The slot leakage can be calculated by making which of the following assumptions ? (a) The current in the slot conductors is uniformly distributed over their cross-section (b) The leakage path is straight across the slot and around the iron at the bottom (c) The permanence of air paths is only considered. The reluctance of iron paths is assumed as zero (d) All of the above

Description : The slot leakage can be calculated by making which of the following assumptions ? (a) The current in the slot conductors is uniformly distributed over their cross-section (b) The leakage path is straight ... is only considered. The reluctance of iron paths is assumed as zero (d) All of the above

Last Answer : (d) All of the above

Leakage current flows through the thyristor in

Description : Leakage current flows through the thyristor in

Last Answer : Leakage current flows through the thyristor in Forward blocking mode and Reverse blocking mode.

In a transistor leakage current mainly depends on

Last Answer : In a transistor leakage current mainly depends on temperature.

The leakage current in a pn junction is of the order of

Description : The leakage current in a pn junction is of the order of

Last Answer : The leakage current in a pn junction is of the order of µA.

The leakage current across a pn junction is due to …………..

Last Answer : The leakage current across a pn junction is due to Minority carriers.

The leakage current of PN junction is caused by?

Description : The leakage current of PN junction is caused by?

Last Answer : The leakage current of PN junction is caused by heat energy.

what is the leakage current of diode?

Last Answer : In Reverse bias of diode when the cathode is connected to positive and anode is connected to negative very small current flows this very small current is known as leakage current of diode.

Describe the concept of leakage flux, useful flux and fringing with neat diagram.

Description : Describe the concept of leakage flux, useful flux and fringing with neat diagram.

Last Answer : Leakage Flux

Define : i) MMF ii) Reluctance iii) Fringing iv) Leakage flux

Description : Define : i) MMF ii) Reluctance iii) Fringing iv) Leakage flux

Last Answer : i) MMF:  It is the force that drives magnetic flux through magnetic circuit. It is measured in amp-turns.  ii) Reluctance (s) :-  Reluctance is the property of the substance ... through the magnetic circuit, leaks through the air surrounding the core. This flux is called as leakage flux.

Leakage fluxes in a transformer may be minimized by :

Description : Leakage fluxes in a transformer may be minimized by : (A) Avoiding overloads (B) Keeping magnetizing current minimum (C) Reducing the reluctance of the iron core to minimum (D) Sectionalizing and interleaving the primary and secondary windings

Last Answer : Leakage fluxes in a transformer may be minimized by : Sectionalizing and interleaving the primary and secondary windings

If a three-phase induction motor malfunctions and drops to a single-phase (one supply line open) ____________. A. the motor will continue to run if it is not heavily loaded B. more torque will be developed C. the motor will immediately stop and not be able to be restarted D. the motor will immediately stop and can only be restarted at no load

Description : If a three-phase induction motor malfunctions and drops to a single-phase (one supply line open) ____________. A. the motor will continue to run if it is not heavily loaded B. more torque will be ... be able to be restarted D. the motor will immediately stop and can only be restarted at no load

Last Answer : Answer: A

Before using an all-purpose electric measuring instrument (multimeter) utilizing internal batteries to supply power for resistance measurements, you should FIRST ____________. A. remove one of the batteries B. remove all the batteries C. calibrate using a known external resistance D. select the proper resistance range

Description : Before using an all-purpose electric measuring instrument (multimeter) utilizing internal batteries to supply power for resistance measurements, you should FIRST ____________. A. remove one of the ... batteries C. calibrate using a known external resistance D. select the proper resistance range

Last Answer : Answer: D

Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three-phase voltage supply C. improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Description : Erratic operation of the devices represented in the diagrams shown in the illustration could be traced to ____________. EL-0092 A. improper contact at 'R' slip rings or 'S' connections B. a low three- ... . improper contact at 'S' slip rings or 'R' connections D. a high three-phase voltage supply

Last Answer : Answer: A

A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Description : A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Last Answer : Answer: D

The circuit shown in the illustration represents a/an ____________. EL-0085 A. operational amplifier B. Wheatstone bridge C. magnetic amplifier D. power supply

Description : The circuit shown in the illustration represents a/an ____________. EL-0085 A. operational amplifier B. Wheatstone bridge C. magnetic amplifier D. power supply

Last Answer : Answer: D

The kVA rating required for a transformer that must handle a maximum load current of 8 A with a ...

Description : The kVA rating required for a transformer that must handle a maximum load current of 8 A with a secondary voltage of 2 kV will be: A. 4 kVA B. 0.25 kVA C. 16 kVA D. 8 kVA

Last Answer : The kVA rating required for a transformer that must handle a maximum load current of 8 A with a secondary voltage of 2 kV will be: 16 kVA

There Are A transformer And An Induction Machine. Those Two Have The Same Supply. For Which Device The Load Current Will Be Maximum? And Why?

Description : There Are A transformer And An Induction Machine. Those Two Have The Same Supply. For Which Device The Load Current Will Be Maximum? And Why?

Last Answer : The motor has max load current compare to that of trformer because the motor consumes real power.. and the trformer is only producing the working flux and its not consuming.. hence the load current in the trformer is because of core loss so it is minimum.

The inrush current of a transformer at no load is maximum if the supply voltage is switched on

Description : The inrush current of a transformer at no load is maximum if the supply voltage is switched on  (1) at peak voltage value (2) at zero voltage value (3) at half voltage value (4) at 0.866 time voltage value

Last Answer : At 0.866 time voltage value

Define : i) Maximum Value ii) RMS Value of ac supply

Description : Define : i) Maximum Value ii) RMS Value of ac supply

Last Answer : i) Maximum Value :- The maximum or peak value attained by an alternating quantity during positive or negative half cycle, is called maximum value or peak value.  ii) RMS Value of ac ... as produced by the alternating current when flowing through the same resistance and for the same time. 

Actual lift of a pump is always less than the theoretical lift and is limited by the (A) Specific gravity & temperature of the liquid (B) Leakage & pressure decreasing at higher elevations (C) Frictional resistance through pipes, fittings & passages (D) All (A), (B) and (C)

Description : Actual lift of a pump is always less than the theoretical lift and is limited by the (A) Specific gravity & temperature of the liquid (B) Leakage & pressure decreasing at higher elevations (C) Frictional resistance through pipes, fittings & passages (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Two taps M and N can alone fill a tank in 80 minutes and 120 minutes respectively. But due to a leakage of tank, it took 12 more minutes to fill the tank. In how many hours, the leak can alone empty the full tank? A) 240 B) 230 C) 248 D) 256

Description : Two taps M and N can alone fill a tank in 80 minutes and 120 minutes respectively. But due to a leakage of tank, it took 12 more minutes to fill the tank. In how many hours, the leak can alone empty the full tank? A) 240 B) 230 C) 248 D) 256

Last Answer : A A and B can fill tank in (1/80 + 1/120) = 1/48 so 48minutes But it took 12 more minutes, this means the tank got full in 48+12= 60 minutes So (1/80 + 1/120 – 1/x) = 1/60 1/X=1/80+1/120-1/60 Solve, x = 240