Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Propellers are
(A) Axial flow mixers
(B) Low speed impeller
(C) Used for mixing liquids of high viscosity
(D) Radial flow mixers
by

1 Answer

Answer :

(A) Axial flow mixers
by

Related questions

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Last Answer : (A) Density of the liquid

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Description : Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Last Answer : (D) None of these

Which of the following agitators having a large blade area, rotating at slow speed is used for mixing high viscosity liquids (> 50000 centipoise)? (A) Propeller(B) Helical screw(C) Flat blade turbine(D) Curved blade turbine

Description : Which of the following agitators having a large blade area, rotating at slow speed is used for mixing high viscosity liquids (> 50000 centipoise)? (A) Propeller (B) Helical screw (C) Flat blade turbine (D) Curved blade turbine

Last Answer : (B) Helical screw

Highly viscous liquids & pastes are agitated by (A) Propellers (B) Turbine agitators (C) Multiple blade paddles (D) None of these

Description : Highly viscous liquids & pastes are agitated by (A) Propellers (B) Turbine agitators (C) Multiple blade paddles (D) None of these

Last Answer : (C) Multiple blade paddles

__________ is an example of axial flow impeller. (A) Paddle (B) Turbine (C) Propeller (D) All (A), (B) and (C)

Description : __________ is an example of axial flow impeller. (A) Paddle (B) Turbine (C) Propeller (D) All (A), (B) and (C)

Last Answer : (C) Propeller

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Last Answer : (A) Axial

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Description : A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Last Answer : (C) Presence of lateral mixing

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction

Description : A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction

Last Answer : (B) Is same as ideal stirred tank reactor

In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Description : In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Last Answer : (B) Velocity of reaction can be controlled

How many mixing speeds are featured on Kitchenaid mixers?

Description : How many mixing speeds are featured on Kitchenaid mixers?

Last Answer : All Kitchenaid mixers include 11 mixing speeds. There is a sliding lever that can be set to speeds label 1 thru 10 as well as a speed labeled 'stir'

The Prandtl mixing length is (A) Zero at the pipe wall and is a universal constant (B) Independent of radial distance from the pipe axis (C) Independent of the shear stress (D) Useful for computing laminar flow problems

Description : The Prandtl mixing length is (A) Zero at the pipe wall and is a universal constant (B) Independent of radial distance from the pipe axis (C) Independent of the shear stress (D) Useful for computing laminar flow problems

Last Answer : (D) Useful for computing laminar flow problems

In an ideal tubular-flow reactor (A) There is no mixing in longitudinal direction (B) Mixing takes place in radial direction (C) There is a uniform velocity across the radius (D) All (A), (B) and (C)

Description : In an ideal tubular-flow reactor (A) There is no mixing in longitudinal direction (B) Mixing takes place in radial direction (C) There is a uniform velocity across the radius (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a measure of its capacity and is equal to the residence time when the density of reaction mixture is constant (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty (D) In an ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Description : Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a ... ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Last Answer : (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty

Turbine impeller (A) Produces only radial current (B) Produces only tangential current (C) Is effective over wide range of viscosities (D) Does not produce tangential current

Description : Turbine impeller (A) Produces only radial current (B) Produces only tangential current (C) Is effective over wide range of viscosities (D) Does not produce tangential current

Last Answer : (C) Is effective over wide range of viscosities

Which one of the following types of compressor is mostly used for supercharging of IC engines? (a) Radial flow compressor (b) Axial flow compressor (c) Root blower (d) Reciprocating compressor

Description : Which one of the following types of compressor is mostly used for supercharging of IC engines? (a) Radial flow compressor (b) Axial flow compressor (c) Root blower (d) Reciprocating compressor

Last Answer : Ans : c

Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Description : Compressor mostly used for supercharging of IC engine is A. Radial flow compressor B. Axial flow compressor C. Root blower compressor D. Reciprocating compressor

Last Answer : ANSWER : A

Which one of the following type of compressor is mostly used for supercharging of I.C engine A. Radial flow compressor B. Axial flow compressor C. Root blower D. Reciprocating compressor.

Description : Which one of the following type of compressor is mostly used for supercharging of I.C engine A. Radial flow compressor B. Axial flow compressor C. Root blower D. Reciprocating compressor.

Last Answer : ANSWER : C

__________ are mixed using ribbon blenders. (A) Lumpy solids and low viscosity liquids (B) Dry powders (C) High viscosity liquids (D) Thick pastes

Description : __________ are mixed using ribbon blenders. (A) Lumpy solids and low viscosity liquids (B) Dry powders (C) High viscosity liquids (D) Thick pastes

Last Answer : (B) Dry powders

Among liquids, water has a comparatively high value of thermal conductivity, due to its (A) Low density (B) High viscosity (C) Partial ionisation (D) Dense structure

Description : Among liquids, water has a comparatively high value of thermal conductivity, due to its (A) Low density (B) High viscosity (C) Partial ionisation (D) Dense structure

Last Answer : (C) Partial ionisation

Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Description : Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Last Answer : ANSWER : C

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocity(B) Newton's law of viscosity is not applicable to the turbulent flow of fluidwith linear velocity distribution(C) Laminar flow of viscous liquids is involved in the lubrication of varioustypes of bearings(D) Rise of water in capillary tubes reduces with the increasing diameter ofcapillary tubes

Description : Pick out the wrong statement. (A) A fluid mass is free from shearing forces, when it is made to rotate with a uniform velocit (B) Newton's law of viscosity is not applicable to the ... types of bearings (D) Rise of water in capillary tubes reduces with the increasing diameter of capillary tubes

Last Answer : (B) Newton's law of viscosity is not applicable to the turbulent flow of fluid with linear velocity distribution

Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Description : Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these

Last Answer : (B) Centrifugal

Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Description : Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Last Answer : (A) Mixing highly viscous pastes

The process of one substance mixing with another because of molecular motion is called _________.  a. diffusion  b. viscosity  c. streamline flow  d. solution

Description : The process of one substance mixing with another because of molecular motion is called _________.  a. diffusion  b. viscosity  c. streamline flow  d. solution

Last Answer : diffusion

A fountain pen works on the principle of (1) Flow of liquids from higher to lower potential (2) Capillary action (3) Bernoulli's principle (4) Viscosity of liquids

Description : A fountain pen works on the principle of (1) Flow of liquids from higher to lower potential (2) Capillary action (3) Bernoulli's principle (4) Viscosity of liquids

Last Answer : (2) Capillary action Explanation: A fountain pen is a nib pen that, unlike its predecessor the dip pen, contains an internal reservoir of water-based liquid ink. The pen draws ink from the ... to flow in narrow spaces without the assistance of, and in opposition to external forces like gravity.

The term "laminar flow" is most often associated with the description of: w) conduction of sound by waves x) current flow in transistors y) effects of viscosity of liquids z) passage of light rays through a liquid

Description : The term "laminar flow" is most often associated with the description of: w) conduction of sound by waves x) current flow in transistors y) effects of viscosity of liquids z) passage of light rays through a liquid

Last Answer : ANSWER: Y -- EFFECTS OF VISCOSITY OF LIQUIDS

A fountain pen works on the principle of (1) flow of liquids from higher to lower potential (2) capillary action (3) Bernoulli’s principle (4) Viscosity of liquids

Description : A fountain pen works on the principle of (1) flow of liquids from higher to lower potential (2) capillary action (3) Bernoulli’s principle (4) Viscosity of liquids

Last Answer : capillary action

At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 /μ: Reynold's number N is the impeller rotational speed, and D is the impeller diameter. (A) Po ∝ Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

In a mixer, the quantity, (v. L/D) is termed as __________ number (where, v = longitudinal velocity of material, L = length of the mixer, D = diffusivity in axial mixing). (A) Weber (B) Peclet (C) Brinkman (D) Schmidt

Description : In a mixer, the quantity, (v. L/D) is termed as __________ number (where, v = longitudinal velocity of material, L = length of the mixer, D = diffusivity in axial mixing). (A) Weber (B) Peclet (C) Brinkman (D) Schmidt

Last Answer : (B) Peclet

In a counter-current extractor, as the axial mixing increases, the extraction efficiency (A) Increases (B) Decreases (C) Remains unchanged (D) Depends on the pressure of the system

Description : In a counter-current extractor, as the axial mixing increases, the extraction efficiency (A) Increases (B) Decreases (C) Remains unchanged (D) Depends on the pressure of the system

Last Answer : (B) Decreases

In most of the mechanically agitated liquid-liquid extractors, baffles or horizontal compartmental plates are provided, which helps in (A) Reducing the axial mixing (B) Increasing the rate of extraction (C) Maintaining the concentration difference between the two phases (D) All 'a', 'b' & 'c'

Description : In most of the mechanically agitated liquid-liquid extractors, baffles or horizontal compartmental plates are provided, which helps in (A) Reducing the axial mixing (B) Increasing the rate of extraction (C) Maintaining the concentration difference between the two phases (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Description : High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these

Last Answer : (C) Axial flow

Ribbon blenders are exclusively meant for (A) Blending miscible liquids (B) Non-flowing powder and thin pastes (C) Bath mixing (D) Continuous mixing

Description : Ribbon blenders are exclusively meant for (A) Blending miscible liquids (B) Non-flowing powder and thin pastes (C) Bath mixing (D) Continuous mixing

Last Answer : (B) Non-flowing powder and thin pastes

If an ideal solution is formed by mixing two pure liquids in any proportion, then the __________ of mixing is zero (A) Enthalpy (B) Volume (C) Both 'a' & 'b' (D) Neither 'a' nor 'b'

Description : If an ideal solution is formed by mixing two pure liquids in any proportion, then the __________ of mixing is zero (A) Enthalpy (B) Volume (C) Both 'a' & 'b' (D) Neither 'a' nor 'b'

Last Answer : (C) Both 'a' & 'b'

Liquids having low viscosity are called?

Description : Liquids having low viscosity are called?

Last Answer : Mobile liquids eg : Water; Kerosene; Alcohol; Petro -

Vacuum filter is most suitable for the (A) Removal of fines from liquid (B) Liquids having high vapour pressure (C) Liquids of very high viscosity (D) None of these

Description : Vacuum filter is most suitable for the (A) Removal of fines from liquid (B) Liquids having high vapour pressure (C) Liquids of very high viscosity (D) None of these

Last Answer : (D) None of these

Solvent extraction is the terminology applied to the liquid-liquid extraction, which is preferred for the separation of the components of liquids, when (A) Extracting solvent is cheaply & abundantly available (B) One of the liquid components is heat sensitive (C) Viscosity of liquid components is very high (D) One of the liquid components has very high affinity towards the solvent

Description : Solvent extraction is the terminology applied to the liquid-liquid extraction, which is preferred for the separation of the components of liquids, when (A) Extracting solvent is cheaply & abundantly available ... very high (D) One of the liquid components has very high affinity towards the solvent

Last Answer : (D) One of the liquid components has very high affinity towards the solvent

Forced circulation evaporators are normally used for concentrating liquids having (A) Scaling characteristics (B) High viscosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Forced circulation evaporators are normally used for concentrating liquids having (A) Scaling characteristics (B) High viscosity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Description : Load acting on bearing in its plane of rotation is called as a... A. Radial load B. Axial load C. Perpendicular load D. Thrust load

Last Answer : A. Radial load

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads