The maximum average depth due to one day storm over an area of 100 km² is 100 mm. Depth￾Area-Duration (DAD) curves indicate the same area of 100 km² the maximum average depth for a 3 hour storm will be (A) 100 mm (B) More than 100 mm (C) Less than 100 mm (D) None of the above

The maximum average depth due to one day storm over an area of 100 km² is 100 mm. Depth￾Area-Duration (DAD) curves indicate the same area of 100 km² the maximum average depth for a
3 hour storm will be
(A) 100 mm
(B) More than 100 mm
(C) Less than 100 mm
(D) None of the above
by

1 Answer

Answer :

Answer: Option B
by

Related questions

For a catchment area of 120 km², the equilibrium discharge in m3/hour of a Scurve obtained by the summation of 6 hour unit hydro graph is (A) 0.2 × 106 (B) 0.6 × 106 (C) 2.4 × 106 (D) 7.2 × 10

Description : For a catchment area of 120 km², the equilibrium discharge in m3/hour of a Scurve obtained by the summation of 6 hour unit hydro graph is (A) 0.2 × 106 (B) 0.6 × 106 (C) 2.4 × 106 (D) 7.2 × 10

Last Answer : Answer: Option A

A unit hydrograph is a hydrograph of a rain storm of a specified duration resulting from a run-off of (A) 15 mm (B) 20 mm (C) 25 mm (D) 30 mm

Description : A unit hydrograph is a hydrograph of a rain storm of a specified duration resulting from a run-off of (A) 15 mm (B) 20 mm (C) 25 mm (D) 30 mm

Last Answer : Answer: Option B

Pick up the correct statement from the following: (A) The unit hydrograph of a specified unit duration obtained from the past data can be used to obtain the hydrograph of future storms of like duration (B) To obtain the ordinates of storm hydrograph, the ordinates of unit hydrograph are multiplied by the multiplying factor (C) The multiplying factor for storm hydrograph may be obtained by dividing the run off in mm by 25 mm (D) All the above

Description : Pick up the correct statement from the following: (A) The unit hydrograph of a specified unit duration obtained from the past data can be used to obtain the hydrograph of future storms of like duration (B) ... hydrograph may be obtained by dividing the run off in mm by 25 mm (D) All the above

Last Answer : Answer: Option D

The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Description : The Maximum spacing of Secondary reinforcement in slabs should be [ A ] Less than 450 mm [ B ] Less than 300 mm [ C ] Smaller of three times the effective depth and 450 mm [ D ] Smaller of five times the effective depth and 450 mm

Last Answer : [ D ] Smaller of five times the effective depth and 450 mm

An intense rain is falling at a uniform rate of 7.5 cm/hour for a period of 60 minutes on a basin whose area is 500 hectares. If the average infiltration capacity during the entire rain period is assumed to be 1.5 cm/hr, the maximum run-off rate based on 10 minute peak percentage of 16% from distributing graph of the basin, is (A) 40 cumecs (B) 60 cumecs (C) 80 cumecs (D) 100 cumecs

Description : An intense rain is falling at a uniform rate of 7.5 cm/hour for a period of 60 minutes on a basin whose area is 500 hectares. If the average infiltration capacity during the entire rain period is assumed to be 1.5 ... of the basin, is (A) 40 cumecs (B) 60 cumecs (C) 80 cumecs (D) 100 cumecs

Last Answer : Answer: Option C

Busy hour traffic is the (A) maximum average simultaneous traffic. (B) traffic during peak hour. (C) traffic when all subscribers are engaged. (D) the duration of maximum calls.

Description : Busy hour traffic is the (A) maximum average simultaneous traffic. (B) traffic during peak hour. (C) traffic when all subscribers are engaged. (D) the duration of maximum calls.

Last Answer : (B) traffic during peak hour.

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

Time of concentration (A) Is the time taken, for precipitation (B) Duration of rainfall (C) Time taken for all the ran off to reach the drain (D) Time taken for the storm water to travel from the most remote point to the drain

Description : Time of concentration  (A) Is the time taken, for precipitation  (B) Duration of rainfall  (C) Time taken for all the ran off to reach the drain  (D) Time taken for the storm water to travel from the most remote point to the drain 

Last Answer : (D) Time taken for the storm water to travel from the most remote point to the drain 

Pick up the correct statement from the following: (A) The specified duration of unit hydrograph, is called unit duration (B) The rain during specified duration, is called unit storm (C) The number of unit hydrographs for a given basin, is theoretically infinite (D) All the above

Description : Pick up the correct statement from the following: (A) The specified duration of unit hydrograph, is called unit duration (B) The rain during specified duration, is called unit storm (C) The number of unit hydrographs for a given basin, is theoretically infinite (D) All the above

Last Answer : Answer: Option D

For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Description : For a continuous slab of 3 m × 3.5 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (A) 50 mm (B) 75 mm (C) 100 mm (D) 120 mm

Last Answer : (B) 75 mm

For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Description : For a continuous slab of 3 m x 35 m size, the minimum overall depth of slab to satisfy vertical deflection limits is (a) 120 mm (b) 100 mm (c) 75 mm (d) 50 mm

Last Answer : (a) 120 mm

The settling velocity of the particles larger than 0.06 mm in a settling tank of depth 2.4 is 0.33 m per sec. The detention period recommended for the tank, is A. 30 minutes B. 1 hour C. 1 hour and 30 minutes D. 2 hours

Description : The settling velocity of the particles larger than 0.06 mm in a settling tank of depth 2.4 is 0.33 m per sec. The detention period recommended for the tank, is A. 30 minutes B. 1 hour C. 1 hour and 30 minutes D. 2 hours

Last Answer : ANS: D

In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Description : In slabs the Maximum horizontal distance between parallel main reinforcement should not exceed i.Three times effective depth ii Five times effective depth iii 300mm iv 450 mm [ A ] i and iii [ B ] i and iv [ C ] ii and iii [ D ] ii and iv

Last Answer : [ A ] i and iii

The respective storm totals at three surrounding stations A, B and C are 110, 90 and 70 mm. If the normal annual precipitation amounts at stations X, A, B and C are respectively 1000, 1100, 1200 and 1250 mm, the estimated storm precipitation at X is (A) 75 mm (B) 77 mm (C) 79 mm

Description : The respective storm totals at three surrounding stations A, B and C are 110, 90 and 70 mm. If the normal annual precipitation amounts at stations X, A, B and C are respectively 1000, 1100, 1200 and 1250 mm, the estimated storm precipitation at X is (A) 75 mm (B) 77 mm (C) 79 mm

Last Answer : Answer: Option B

Which of the following ranges identifies the amount of pressure within the endotracheal tube cuff that is believed to prevent both injury and aspiration? a) 20-25 mm Hg water pressure. Usually the pressure is maintained at less than 25 cm water pressure to prevent injury and at more than 20 cm water pressure to prevent aspiration. b) 10-15 mm Hg water pressure. A measure of 10–15 mm Hg water pressure would indicate that the cuff is underinflated. c) 30-35 mm Hg water pressure. A measure of 30–35 mm Hg water pressure would indicate that the cuff is overinflated. d) 0-5 mm Hg water pressure A measure of 0-5 mm Hg water pressure would indicate that the cuff is underinflated.

Description : Which of the following ranges identifies the amount of pressure within the endotracheal tube cuff that is believed to prevent both injury and aspiration? a) 20-25 mm Hg water pressure. Usually the ... pressure A measure of 0-5 mm Hg water pressure would indicate that the cuff is underinflated.

Last Answer : a) 20-25 mm Hg water pressure. Usually the pressure is maintained at less than 25 cm water pressure to prevent injury and at more than 20 cm water pressure to prevent aspiration.

Pick up the correct statement from the following: A. The maximum rate of storm runoff is called peak drainage discharge B. Rational method of estimating peak run off, may be used precisely for areas less than 50 hectares C. The period after which the entire area starts contributing to the runoff, is called the time of concentration D. All the above

Description : Pick up the correct statement from the following: A. The maximum rate of storm runoff is called peak drainage discharge B. Rational method of estimating peak run off, may be used precisely for ... entire area starts contributing to the runoff, is called the time of concentration D. All the above

Last Answer : ANS: D

Pick up the correct statement from the following: (A) The tides at any place occur a little less than 1 hour later, each succeeding day (B) The influence of the earth's gravity alone produces level-tidal less sea (C) The spinning force is maximum at the equator and zero at the poles (D) All of the above

Description : Pick up the correct statement from the following: (A) The tides at any place occur a little less than 1 hour later, each succeeding day (B) The influence of the earth's gravity alone produces level-tidal ... ) The spinning force is maximum at the equator and zero at the poles (D) All of the above

Last Answer : (D) All of the above

To compensate the loss of tractive force of vehicles along curves of radius R, the percentage reduction of gradient, is (A) 50/R (B) 75/R (C) 100/R (D) 125/R

Description : To compensate the loss of tractive force of vehicles along curves of radius R, the percentage reduction of gradient, is (A) 50/R (B) 75/R (C) 100/R (D) 125/R

Last Answer : Answer: Option B

When the nurse notes that the post cardiac surgery patient demonstrates low urine output (< 25 ml/hr) with high specific gravity (> 1.025), the nurse suspects: a) Inadequate fluid volume Urine output of less than 25 ml/hr may indicate a decrease in cardiac output. A high specific gravity indicates increased concentration of solutes in the urine which occurs with inadequate fluid volume. b) Normal glomerular filtration Indices of normal glomerular filtration are output of 25 ml or greater per hour and specific gravity between 1.010 and 1.025. c) Overhydration Overhydration is manifested by high urine output with low specific gravity. d) Anuria The anuric patient does not produce urine.

Description : When the nurse notes that the post cardiac surgery patient demonstrates low urine output (< 25 ml/hr) with high specific gravity (> 1.025), the nurse suspects: a) Inadequate fluid volume Urine ... by high urine output with low specific gravity. d) Anuria The anuric patient does not produce urine.

Last Answer : a) Inadequate fluid volume Urine output of less than 25 ml/hr may indicate a decrease in cardiac output. A high specific gravity indicates increased concentration of solutes in the urine which occurs with inadequate fluid volume.

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

Pick up the correct statement from the following: (A) Safety fences are provided on either side of a roadway if embankments are in excess of 6 metres (B) Safety fences are provided on outside of the curves of radii less than 750 m if the embankments are between 3 metres and 6 metres (C) Guard stones are provided at 2.5 metres intervals if embankments are between 1.6 metres to 3 metres (D) All the above

Description : Pick up the correct statement from the following: (A) Safety fences are provided on either side of a roadway if embankments are in excess of 6 metres (B) Safety fences are provided on outside of the ... 2.5 metres intervals if embankments are between 1.6 metres to 3 metres (D) All the above

Last Answer : Answer: Option D

Widening of the roads on curves in hilly region, is done (A) On the outer side (B) On the inner side (C) On the outer and inner sides equally (D) Less on outer side and more on inner side

Description : Widening of the roads on curves in hilly region, is done (A) On the outer side (B) On the inner side (C) On the outer and inner sides equally (D) Less on outer side and more on inner side

Last Answer : Answer: Option B

The maximum safe speed on roads, depends on the (A) Type of road surface (B) Type of curves (C) Sight distance (D) All the above

Description : The maximum safe speed on roads, depends on the (A) Type of road surface (B) Type of curves (C) Sight distance (D) All the above

Last Answer : Answer: Option D

Floating gradients are generally provided (A) Along maximum gradients (B) Along minimum gradients (C) At summit curves (D) At valley curves

Description : Floating gradients are generally provided (A) Along maximum gradients (B) Along minimum gradients (C) At summit curves (D) At valley curves

Last Answer : Answer: Option C

To ensure that bullock carts may not overturn on curves, the maximum value of super-elevation, recommended by I.R.C., is (A) 1 in 10 (B) 1 in 12 (C) 1 in 15 (D) 1 in 20

Description : To ensure that bullock carts may not overturn on curves, the maximum value of super-elevation, recommended by I.R.C., is (A) 1 in 10 (B) 1 in 12 (C) 1 in 15 (D) 1 in 20

Last Answer : Answer: Option C

For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Description : For a simply supported beam of span 15 m, the minimum effective depth to satisfy the vertical deflection limits should be (A) 600 mm (B) 750 mm (C) 900 mm (D) More than 1 m

Last Answer : Answer: Option B

Do leaves on a tree really indicate the coming of a storm?

Description : Do leaves on a tree really indicate the coming of a storm?

Last Answer : It doesn't have to be a storm. The leaves will turn when it is very humid or before it rains, period. It isn't that it is necessarily going to storm.. it just means that the atmosphere has a lot ... soft and they sort of wilt. From the ground, it appears as if they are turning before it rains. :)

The rainfall on five successive days on a catchment was 3, 6, 9, 5 and 1 cm respectively. If the  -index for the storm can be assumed to be 3 cm/day, the total direct runoff from the catchment due to this storm is (a) 11 cm (b) 24 cm (c) 9 cm (d) 20 cm

Description : The rainfall on five successive days on a catchment was 3, 6, 9, 5 and 1 cm respectively. If the  -index for the storm can be assumed to be 3 cm/day, the total direct runoff from the catchment due to this storm is (a) 11 cm (b) 24 cm (c) 9 cm (d) 20 cm

Last Answer : (a) 11 cm

In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Description : In reinforced concrete footing on soil, the minimum thickness at edge should not be less than (A) 100 mm (B) 150 mm (C) 200 mm (D) 250 mm

Last Answer : Answer: Option B

A hardness depth of about 3 mm can be achieved by induction hardness in __________ seconds. (A) 5 (B) 100 (C) 250 (D) 500

Description : A hardness depth of about 3 mm can be achieved by induction hardness in __________ seconds. (A) 5 (B) 100 (C) 250 (D) 500

Last Answer : (A) 5

The compressive strength of 100 mm cube as compared to 150 mm cube is always (A) Less (B) More (C) Equal (D) None of the above

Description : The compressive strength of 100 mm cube as compared to 150 mm cube is always (A) Less (B) More (C) Equal (D) None of the above

Last Answer : Answer: Option B

The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for maximum strength are: (A) b = 57.73 cm d = 81.65 cm (B) b = 81.65 cm d = 57.73 cm (C) b = 50.00 cm d = 50.00 cm (D) b = 40.00 cm d = 80.00 cm

Description : The width b and depth d of a beam cut from a wooden cylindrical log of 100 cm diameter for  maximum strength are:  (A) b = 57.73 cm d = 81.65 cm  (B) b = 81.65 cm d = 57.73 cm  (C) b = 50.00 cm d = 50.00 cm  (D) b = 40.00 cm d = 80.00 cm 

Last Answer : (A) b = 57.73 cm d = 81.65 cm 

The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm

Description : The maximum thickness of expansion joint in rigid pavements is (A) 0 (B) 25 mm (C) 50 mm (D) 100 mm

Last Answer : Answer: Option B

The maximum total settlement for raft foundation on clayey soils should be limited to (A) 25 mm (B) 25 to 40 mm (C) 40 to 65 mm (D) 65 to 100 mm

Description : The maximum total settlement for raft foundation on clayey soils should be limited to (A) 25 mm (B) 25 to 40 mm (C) 40 to 65 mm (D) 65 to 100 mm

Last Answer : Answer: Option D

The maximum total settlement for isolated foundations on clayey soils should be limited to (A) 25 mm (B) 40 mm (C) 65 mm (D) 100 mm

Description : The maximum total settlement for isolated foundations on clayey soils should be limited to (A) 25 mm (B) 40 mm (C) 65 mm (D) 100 mm

Last Answer : Option C

If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier (C) Is equal to the depth of critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Description : If the depth of actual neutral axis of a doubly reinforced beam (A) Is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier (B) Is less ... critical neutral axis; the concrete and steel attain their maximum stresses simultaneously (D) All the above

Last Answer : Answer: Option D

Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach its maximum permissible value first. (c) The moment of resistance will be less than that of the balanced section. (d) The concrete on the tension side is also be considered for calculating the moment of resistance of the section.

Description : Regarding the working stress design of under reinforced concrete section, (a) The neutral axis depth will be greater than that of a balanced section. (b) The stress in steel intension will reach ... on the tension side is also be considered for calculating the moment of resistance of the section.

Last Answer : both b&c

The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Description : The Maximum spacing of Main reinforcement „m‟ slabs shall be [ A ] Less than three times of the effective depth [ B ] Less than 300mm [ C ] Smaller of (a) and (b) [ D ] Greater of (a) and (b)

Last Answer : [ C ] Smaller of (a) and (b)

The area bounded by the curves `y=6x-x^(2)` and `y=x^(2)-2x` is less then

Description : The area bounded by the curves `y=6x-x^(2)` and `y=x^(2)-2x` is less then

Last Answer : The area bounded by the curves `y=6x-x^(2)` and `y=x^(2)-2x` is less then A. 18 B. 19 C. 22 D. 20

For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Last Answer : (a) 1.5 mm less than the plate thickness

The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Description : The Minimum bar spacing should not be less than [ A ] Diameter of the largest bar [ B ] Maximum size of aggregate [ C ] Greater of diameter of the largest bar and maximum size of aggregate [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Last Answer : [ D ] Greater of diameter of the largest bar and maximum size of aggregate plus 5 mm

Maximum root zone depth for Maize (a) 200-300 mm (b) 400-600 mm (c) 500-600 mm (d) 350- 450 mm

Description : Maximum root zone depth for Maize (a) 200-300 mm (b) 400-600 mm (c) 500-600 mm (d) 350- 450 mm

Last Answer : (b) 400-600 mm

A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Description : A uniformly distributed load of 20 kN/m acts on a simply supported beam of rectangular cross section of width 20 mm and depth 60 mm. What is the maximum bending stress acting on the beam of 5m? a. 5030 Mpa b. 5208 Mpa c. 6600 Mpa d. Insufficient data

Last Answer : b. 5208 Mpa

If the radii of a compound curve and a reverse curve are respectively the same, the length of common tangent (A) Of compound curve will be more (B) Of reverse curve will be more (C) Of both curves will be equal (D) None of these

Description : If the radii of a compound curve and a reverse curve are respectively the same, the length of common tangent (A) Of compound curve will be more (B) Of reverse curve will be more (C) Of both curves will be equal (D) None of these

Last Answer : Answer: Option C

A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm

Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free  end. If the modulus of elasticity of the material is 0.2 × 106  N/mm2 , the deflection of the free end,  is  (A) 2 mm  (B) 3 mm  (C) 4 mm  (D) 5 mm

Last Answer : (D) 5 mm

Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm

Description : Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm

Last Answer : [ D ] 750 mm

¾th or ¼th extra space is left in sewer pipes at maximum discharge for A. Low estimates of the average and maximum flows B. Large scale infiltration of storm water C. Unexpected increase in population D. All the above

Description : ¾th or ¼th extra space is left in sewer pipes at maximum discharge for A. Low estimates of the average and maximum flows B. Large scale infiltration of storm water C. Unexpected increase in population D. All the above

Last Answer : ANS: D

If the coefficient of friction on the road surface is 0.15 and a maximum super-elevation 1 in 15 is provided, the maximum speed of the vehicles on a curve of 100 metre radius, is (A) 32.44 km/hour (B) 42.44 kg/hour (C) 52.44 km/hour (D) 62.44 km/hour

Description : If the coefficient of friction on the road surface is 0.15 and a maximum super-elevation 1 in 15 is provided, the maximum speed of the vehicles on a curve of 100 metre radius, is (A) 32.44 km/hour (B) 42.44 kg/hour (C) 52.44 km/hour (D) 62.44 km/hour

Last Answer : Answer: Option C