Widening of the roads on curves in hilly region, is done (A) On the outer side (B) On the inner side (C) On the outer and inner sides equally (D) Less on outer side and more on inner side

Widening of the roads on curves in hilly region, is done
(A) On the outer side
(B) On the inner side
(C) On the outer and inner sides equally
(D) Less on outer side and more on inner side
by

1 Answer

Answer :

Answer: Option B
by

Related questions

The width of different roads as recommended in Nagpur plan by the Indian Road Conference for hilly region, is (A) Same for National Highways (B) Different for National Highways (C) Same for State Highways (D) Same for Major District roads

Description : The width of different roads as recommended in Nagpur plan by the Indian Road Conference for hilly region, is (A) Same for National Highways (B) Different for National Highways (C) Same for State Highways (D) Same for Major District roads

Last Answer : Answer: Option B

no super elevation is provided on a road along curves, pot holes may develop at (A) Inner edge of the road (B) Outer edge of the road (C) Centre of the road (D) Nowhere on the road

Description : no super elevation is provided on a road along curves, pot holes may develop at (A) Inner edge of the road (B) Outer edge of the road (C) Centre of the road (D) Nowhere on the road

Last Answer : Answer: Option B

The most commonly adopted method to provide super-elevation on roads, is by pivoting the road surface about (A) Outer edge so that the inner edge is lowered (B) Crown so that outer edge is raised and inner edge is lowered (C) Inner edge so that outer edge is raised (D) None of these

Description : The most commonly adopted method to provide super-elevation on roads, is by pivoting the road surface about (A) Outer edge so that the inner edge is lowered (B) Crown so that outer edge is raised and inner edge is lowered (C) Inner edge so that outer edge is raised (D) None of these

Last Answer : Answer: Option C

State the necessity of providing extra widening on horizontal curves.

Description : State the necessity of providing extra widening on horizontal curves.

Last Answer : The necessity of providing extra widening on horizontal curves: - 1) When a vehicle travels on horizontal curves, it occupies more width than that it occupies on straight road. This reduces the capacity ... 5) Drivers have psychological fear to drive close to the edge of the pavements on curves.

The usual width of side drains along Highways in hilly region, is (A) 50 cm (B) 60 cm (C) 70 cm (D) 100 cm

Description : The usual width of side drains along Highways in hilly region, is (A) 50 cm (B) 60 cm (C) 70 cm (D) 100 cm

Last Answer : Answer: Option B

According to IRC : 52-1973, for a single lane National Highway in hilly region, (A) Width of the carriageway must be 3.75 m (B) Shoulders on either side must be 1.25 m (C) Total width of the road-way must be 6.25 m (D) Total of the above

Description : According to IRC : 52-1973, for a single lane National Highway in hilly region, (A) Width of the carriageway must be 3.75 m (B) Shoulders on either side must be 1.25 m (C) Total width of the road-way must be 6.25 m (D) Total of the above

Last Answer : Answer: Option D

Border Roads Organisation for hilly regions (India), was formed in (A) 1947 (B) 1954 (C) 1958 (D) 1960

Description : Border Roads Organisation for hilly regions (India), was formed in (A) 1947 (B) 1954 (C) 1958 (D) 1960

Last Answer : Answer: Option D

The gradients of trace cuts for hilly roads, are kept (A) Equal to ruling gradient (B) 10 to 20 per cent easier than ruling gradients (C) 10 to 20 per cent steeper than ruling gradients (D) None of these

Description : The gradients of trace cuts for hilly roads, are kept (A) Equal to ruling gradient (B) 10 to 20 per cent easier than ruling gradients (C) 10 to 20 per cent steeper than ruling gradients (D) None of these

Last Answer : Answer: Option B

Side drains on both sides of a hill road, are essential when the road is (A) Along the spur curves (B) Along the re-entrant curves (C) In cutting (D) None of these

Description : Side drains on both sides of a hill road, are essential when the road is (A) Along the spur curves (B) Along the re-entrant curves (C) In cutting (D) None of these

Last Answer : Answer: Option C

The maximum safe speed on roads, depends on the (A) Type of road surface (B) Type of curves (C) Sight distance (D) All the above

Description : The maximum safe speed on roads, depends on the (A) Type of road surface (B) Type of curves (C) Sight distance (D) All the above

Last Answer : Answer: Option D

The type of transition curves generally provided on hill roads, is (A) Circular (B) Cubic parabola (C) Lemniscate (D) Spiral

Description : The type of transition curves generally provided on hill roads, is (A) Circular (B) Cubic parabola (C) Lemniscate (D) Spiral

Last Answer : Answer: Option D

Hill roads are (A) Provided camber along spur curves (B) Provided camber along valley curves (C) Seldom provided a camber (D) None of these

Description : Hill roads are (A) Provided camber along spur curves (B) Provided camber along valley curves (C) Seldom provided a camber (D) None of these

Last Answer : Answer: Option C

In hill roads the side drains arc provided (A) Only on the hill side of road (B) Only on the opposite side of hill (C) On both sides of roa(D) None of the above

Description : In hill roads the side drains arc provided (A) Only on the hill side of road (B) Only on the opposite side of hill (C) On both sides of roa (D) None of the above

Last Answer : Answer: Option A

Along a hill road, a side drain is provided on (A) Outer side of a spur curve(B) Outer side of a re-entrant curve (C) Outer side of both (a) and (b) (D) Inner side of both (a) and (b)

Description : Along a hill road, a side drain is provided on (A) Outer side of a spur curve (B) Outer side of a re-entrant curve (C) Outer side of both (a) and (b) (D) Inner side of both (a) and (b)

Last Answer : Answer: Option D

Formation width of a hill road is the distance between (A) Outer end of side drain to outer end of parapet wall (B) Outer end of side drain to inner end of parapet wall (C) Inner end of side drain to outer end of parapet wall (D) Inner end of side drain to inner end of parapet wall

Description : Formation width of a hill road is the distance between (A) Outer end of side drain to outer end of parapet wall (B) Outer end of side drain to inner end of parapet wall (C) Inner end of side drain to outer end of parapet wall (D) Inner end of side drain to inner end of parapet wall

Last Answer : Answer: Option A

Why is it dangerous to drive on hilly roads ?

Description : Why is it dangerous to drive on hilly roads ?

Last Answer : Hilly roads are usually winding. Many times there are also invisible curves so that the next road is at about 900 angles. This is why driving on hilly roads is extremely dangerous.

What are the precautions to be taken on hilly roads ?

Last Answer : Maintain a safe distance from the car in front. Carefully move up slowly in gear 1 or first gear. You have to go to the top of the hill and climb more slowly , because the visibility on ... to maintain additional distance from the vehicle in front. No overtaking can be done during the ups and downs.

What is the main natural cause of disruption of roads in hilly areas

Description : What is the main natural cause of disruption of roads in hilly areas

Last Answer : landslide

State any four preventive measures of landslides in hilly roads

Description : State any four preventive measures of landslides in hilly roads

Last Answer : a) By providing proper and effective drainage system to intercept and divert seeping water b) By constructing buttress at toe and providing retaining structures c) By providing slopes and their treatment to ... g) By providing nets. h) Chemical treatment. i) Growth of vegetation on the slopes.

The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Description : The temperature reinforcement in the vertical slab of a T-shaped R.C. retaining wall is (A) Not needed (B) Provided equally on inner and front faces (C) Provided more on inner face than on front face (D) Provided more on front face than on inner face

Last Answer : Answer: Option D

The usual width of parapet walls along Highways in hilly region, is (A) 50 cm (B) 60 cm (C) 70 cm (D) 80 cm

Description : The usual width of parapet walls along Highways in hilly region, is (A) 50 cm (B) 60 cm (C) 70 cm (D) 80 cm

Last Answer : Answer: Option B

Pick up the correct statement from the following: (A) Safety fences are provided on either side of a roadway if embankments are in excess of 6 metres (B) Safety fences are provided on outside of the curves of radii less than 750 m if the embankments are between 3 metres and 6 metres (C) Guard stones are provided at 2.5 metres intervals if embankments are between 1.6 metres to 3 metres (D) All the above

Description : Pick up the correct statement from the following: (A) Safety fences are provided on either side of a roadway if embankments are in excess of 6 metres (B) Safety fences are provided on outside of the ... 2.5 metres intervals if embankments are between 1.6 metres to 3 metres (D) All the above

Last Answer : Answer: Option D

In highway construction on super-elevated curves, the rolling shall proceed from (A) Sides towards the centre (B) Centre towards the sides (C) Lower edge towards the upper edge (D) Upper edge towards the lower edge

Description : In highway construction on super-elevated curves, the rolling shall proceed from (A) Sides towards the centre (B) Centre towards the sides (C) Lower edge towards the upper edge (D) Upper edge towards the lower edge

Last Answer : Answer: Option C

The graph shown in the illustration represents the speed droop curves of two equal capacity alternators about to be paralleled. When paralleled, the greater portion of the total load above 60% for each unit will be picked up _____________. EL-0025 A. by unit 'A' B. by unit 'B' C. equally by each unit D. none of the above

Description : The graph shown in the illustration represents the speed droop curves of two equal capacity alternators about to be paralleled. When paralleled, the greater portion of the total load above 60% for each unit will be picked up ... unit 'A' B. by unit 'B' C. equally by each unit D. none of the above

Last Answer : Answer: A

Before providing super-elevation on roads, the portion of the carriageway between the crown and the outer edge is made (A) To have a reduced fall (B) Horizontal (C) To have slope of the camber on the other half of the carriageway (D) None of these

Description : Before providing super-elevation on roads, the portion of the carriageway between the crown and the outer edge is made (A) To have a reduced fall (B) Horizontal (C) To have slope of the camber on the other half of the carriageway (D) None of these

Last Answer : Answer: Option C

Roads are bent inwards on curves. Why?

Description : Roads are bent inwards on curves. Why?

Last Answer : Ans: The roads are bent inwards on the curves and at the turns because the bents avoid falling outside and prevent the accidents. OR When an object turns in a circle it is influenced by a centrifugal ... in a way that these bent inward at the turns to avoid falling outside and to prevent accidents.

Roads are bent inwards on curves.

Description : Roads are bent inwards on curves.

Last Answer : 1- The centrifugal force experienced by the vehicle is lowered by the raised end, so the vehicle doesn’t skit or goes off from the road. 2- The centripetal force is supplemented by the gravitaional forces from below.

List various types of curves provided on Hill Roads.

Description : List various types of curves provided on Hill Roads. 

Last Answer : Types of curves provided on hill roads: - 1) Hair pin curves 2) Salient curves 3) Re-entrant curves

Read the different components from (i) to (iv) in the list given below and tell the correct order of the components with reference to their arrangement from outer side to inner side in a woody dicot stem. (i) Secondary cortex (ii) Wood (iii)Secondary phloem (iv) Phellem The correct order is (a) (iv), (i), (iii), (ii) (b) (iv), (iii), (i), (ii) (c) (iii), (iv), (ii), (i) (d) (i), (ii), (iv), (iii).

Description : Read the different components from (i) to (iv) in the list given below and tell the correct order of the components with reference to their arrangement from outer side to inner side in a woody dicot stem. (i) Secondary cortex (ii) Wood ... ) (c) (iii), (iv), (ii), (i) (d) (i), (ii), (iv), (iii).

Last Answer : (a) (iv), (i), (iii), (ii)

When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that (A) The head of the load reaches the section (B) The tail of the load reaches the section (C) The load position should be such that the section divides it equally on both sides (D) The load position should be such that the section divides the load in the same ratio as it divides the span

Description : When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that (A) The head of the load ... position should be such that the section divides the load in the same ratio as it divides the span

Last Answer : (D) The load position should be such that the section divides the load in the same ratio as it divides the span

If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque  when t attains maximum shear stress fs  the ratio of inner diameter to outer diameter, is 17/64  (fs/N)  (A) 1/2  (B) 1/3  (C) 1/4  (D) 1/5

Last Answer : (C) 1/4 

The yield moment of a cross section is defined as the moment that will just produce the yield stress in (A) The outer most fibre of the section (B) The inner most fibre of the section (C) The neutral fibre of the section (D) The fibre everywhere

Description : The yield moment of a cross section is defined as the moment that will just produce the yield  stress in  (A) The outer most fibre of the section  (B) The inner most fibre of the section  (C) The neutral fibre of the section  (D) The fibre everywhere 

Last Answer : (A) The outer most fibre of the section 

Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of the column (C) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Description : Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than (A) 42 diameters from the centre of the column (B) 42 diameters from the inner edge of ... ) 42 diameters from the outer edge of the column (D) 24 diameters from the centre of the column

Last Answer : Answer: Option C

Raising of outer edge of a road with respect to inner edge, is known (A) Super elevation (B) Cant (C) Banking (D) All the above

Description : Raising of outer edge of a road with respect to inner edge, is known (A) Super elevation (B) Cant (C) Banking (D) All the above

Last Answer : Answer: Option D

If the width of carriage way is 12.5 metres, outer edge 50 cm higher than the inner edge, the required super elevation is (A) 50 cm (B) 1 in 25 (C) 1 in 400 (D) 1 in 40

Description : If the width of carriage way is 12.5 metres, outer edge 50 cm higher than the inner edge, the required super elevation is (A) 50 cm (B) 1 in 25 (C) 1 in 400 (D) 1 in 40

Last Answer : Answer: Option B

If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Last Answer : (B) Always between h1 and h2

What is the major factor that makes coaxial cable less susceptible to noisethan twisted-pair cable? A) inner conductor B) diameterof cable C) outer conductor D) insulating material

Description : What is the major factor that makes coaxial cable less susceptible to noisethan twisted-pair cable? A) inner conductor B) diameterof cable C) outer conductor D) insulating material

Last Answer : outer conductor

Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its(A) Inner diameter(B) Outer diameter(C) Thickness(D) Neither inner nor outer diameter

Description : Nominal Pipe Size (NPS) of a pipe less than 12 inches in diameter indicates its (A) Inner diameter (B) Outer diameter (C) Thickness (D) Neither inner nor outer diameter

Last Answer : (D) Neither inner nor outer diameter

A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Description : A vessel is said to be thin if a. Its wall has less thickness b. Stresses are uniform over the entire thickness c. Stresses vary at inner and at outer radius d. None of the above

Last Answer : b. Stresses are uniform over the entire thickness

In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Description : In bridge widening projects, the method of stitching is normally employed for connecting existing deck to the new deck. What are the problems associated with this method in terms of shrinkage of concrete?

Last Answer : In the method of stitching, it is a normal practice to construct the widening part of the bridge at first and let it stay undisturbed for several months. After that, concreting will then be ... Stitching refers to formation of a segment of bridge deck between an existing bridge and a new bridge.

Extra widening required at a horizontal curve on a single lane hill road of radius 80 m for a design speed of 50 km ph and for a vehicle with wheel base 6.0 m is (A) 0.225 m (B) 0.589 m (C) 1.250 m (D) None of these

Description : Extra widening required at a horizontal curve on a single lane hill road of radius 80 m for a design speed of 50 km ph and for a vehicle with wheel base 6.0 m is (A) 0.225 m (B) 0.589 m (C) 1.250 m (D) None of these

Last Answer : Answer: Option B

Length of vehicles does not affect (A) Extra widening (B) Minimum radius of turning (C) Passing sight distance (D) Width of shoulders

Description : Length of vehicles does not affect (A) Extra widening (B) Minimum radius of turning (C) Passing sight distance (D) Width of shoulders

Last Answer : Answer: Option D

The total value of extra widening required at a horizontal curve on a two lane hill road of radius 42 m for a design speed of 50 kmph and for vehicles with wheel base 6 m, is (A) 0.500 m (B) 0.589 m (C) 1.089 m (D) 0.089 m

Description : The total value of extra widening required at a horizontal curve on a two lane hill road of radius 42 m for a design speed of 50 kmph and for vehicles with wheel base 6 m, is (A) 0.500 m (B) 0.589 m (C) 1.089 m (D) 0.089 m

Last Answer : Answer: Option C

The Chennai – Bengaluru – Coimbatore - Madurai region is ______. (a) A major industrial region (b) A major agricultural region (c) Mangrove forest region (d) Dry Mountainous (Hilly) region

Description : The Chennai – Bengaluru – Coimbatore - Madurai region is ______. (a) A major industrial region (b) A major agricultural region (c) Mangrove forest region (d) Dry Mountainous (Hilly) region

Last Answer : Ans: (a)

The critical combination of stresses for corner region in cement concrete roads is (A) Load stress + warping stress frictional stress (B) Load stress + warping stress + frictional stress (C) Load stress + warping stress (D) Load stress + frictional stress

Description : The critical combination of stresses for corner region in cement concrete roads is (A) Load stress + warping stress frictional stress (B) Load stress + warping stress + frictional stress (C) Load stress + warping stress (D) Load stress + frictional stress

Last Answer : Answer: Option C

Setting out of Lemniscate transition curves, is done with (A) Perpendicular offsets (B) Radial offsets (C) Deflection angles (D) Polar deflection angles

Description : Setting out of Lemniscate transition curves, is done with (A) Perpendicular offsets (B) Radial offsets (C) Deflection angles (D) Polar deflection angles

Last Answer : Answer: Option D

Ferromagnetic materials owe their properties to __________ inner subshells. (A) Completely filled (B) Partially filled (C) Equally filled (D) Vacant

Description : Ferromagnetic materials owe their properties to __________ inner subshells. (A) Completely filled (B) Partially filled (C) Equally filled (D) Vacant

Last Answer : Option B

The maximum average depth due to one day storm over an area of 100 km² is 100 mm. Depth￾Area-Duration (DAD) curves indicate the same area of 100 km² the maximum average depth for a 3 hour storm will be (A) 100 mm (B) More than 100 mm (C) Less than 100 mm (D) None of the above

Description : The maximum average depth due to one day storm over an area of 100 km² is 100 mm. Depth￾Area-Duration (DAD) curves indicate the same area of 100 km² the maximum average depth for a 3 hour storm will be (A) 100 mm (B) More than 100 mm (C) Less than 100 mm (D) None of the above

Last Answer : Answer: Option B

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

Which has more to offer an explorer, inner space or outer space?

Description : Which has more to offer an explorer, inner space or outer space?

Last Answer : Until they get some kind of FTL drive working, outer space might not hold a lot of promise. I’m all for building a gigantic ship that can be home to generations of explorer’s, though. As long as it’s designed by Hollywood and not a submarine builder.