Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when (A) Strain rate is increased (B) Grain size is increased (C) Prior cold deformation is increased (D) Not affected by any of the above parameters

Other parameters remaining same, the recrystallisation temperature of an alloy is lowered, when
(A) Strain rate is increased
(B) Grain size is increased
(C) Prior cold deformation is increased
(D) Not affected by any of the above parameters
by

1 Answer

Answer :

(A) Strain rate is increased
by

Related questions

Pick out the wrong statement. (A) Lead can creep under its own weight at room temperature (B) The electrical conductivity of gold is considerably reduced by alloying additions due to the decrease in electron movement (C) Recrystallisation temperature decreases with decrease in strain in a cold worked metal (D) With increase in temperature, the electrical conductivity of intrinsic semi-conductor will increase

Description : Pick out the wrong statement. (A) Lead can creep under its own weight at room temperature (B) The electrical conductivity of gold is considerably reduced by alloying additions due to ... metal (D) With increase in temperature, the electrical conductivity of intrinsic semi-conductor will increase

Last Answer : (C) Recrystallisation temperature decreases with decrease in strain in a cold worked metal

Pick out the wrong statement. (A) Tin can be readily and very easily drawn into very fine wire (B) Tin can be severely cold worked without the necessity of annealing due to its low recrystallisation temperature (C) Tin exists in two allotropic forms

Description : Pick out the wrong statement. (A) Tin can be readily and very easily drawn into very fine wire (B) Tin can be severely cold worked without the necessity of annealing due to its low recrystallisation temperature (C) Tin exists in two allotropic forms

Last Answer : (A) Tin can be readily and very easily drawn into very fine wire

Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its fatigue strength (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Description : Pick out the wrong statement. (A) The toughness of a material decreases, when it is heated (B) Crane hooks are normally made of wrought iron (C) Cold working of a metal decreases its ... (D) The temperature at which new grains are formed in a metal is known as the recrystallisation temperature

Last Answer : (C) Cold working of a metal decreases its fatigue strength

03. A fluid whose viscosity changes with the rate of deformation or shear strain is known as Non￾Newtonian fluid. A) True B) False

Description : 03. A fluid whose viscosity changes with the rate of deformation or shear strain is known as Non￾Newtonian fluid. A) True B) False

Last Answer : A

A fluid whose viscosity does not change with the rate of deformation or shear strain is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Description : A fluid whose viscosity does not change with the rate of deformation or shear strain is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Last Answer : Answer: Option C

Stoke's law states that the velocity at which a grain settles out of suspension, the other factors remaining constant, is dependent upon (A) Shape of grain (B) Weight of grain (C) Size of grain (D) Shape, size and weight of grain

Description : Stoke's law states that the velocity at which a grain settles out of suspension, the other factors remaining constant, is dependent upon (A) Shape of grain (B) Weight of grain (C) Size of grain (D) Shape, size and weight of grain

Last Answer : Answer: Option D

Secondary hardening in steels arises out of the (A) Precipitation of fine alloy carbides at high temperatures (B) Refinement of ferrite grain size by working (C) Decomposition of retained austenite upon heat treatment (D) Precipitation of complex inter-metallic upon heat treatment

Description : Secondary hardening in steels arises out of the (A) Precipitation of fine alloy carbides at high temperatures (B) Refinement of ferrite grain size by working (C) Decomposition of retained austenite upon heat treatment (D) Precipitation of complex inter-metallic upon heat treatment

Last Answer : Option C

__________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning

Description : __________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning

Last Answer : (C) Strain ageing

While the recrystallisation temperature for pure metals is 0.3 Tm, the same for alloys is equal to __________ × Tm (where, Tm Melting temperature). (A) 0.25 (B) 0.45 (C) 0.70 (D) 0.95

Description : While the recrystallisation temperature for pure metals is 0.3 Tm, the same for alloys is equal to __________ × Tm (where, Tm Melting temperature). (A) 0.25 (B) 0.45 (C) 0.70 (D) 0.95

Last Answer : (C) 0.70

Pick out the wrong statement. (A) Bronze is an alloy of copper & tin (B) Brass is an alloy of copper & zinc (C) The alloy named 'German silver' does not contain any silver (D) The ability of a material to fracture without appreciable deformation is called its ductility

Description : Pick out the wrong statement. (A) Bronze is an alloy of copper & tin (B) Brass is an alloy of copper & zinc (C) The alloy named 'German silver' does not contain any silver (D) The ability of a material to fracture without appreciable deformation is called its ductility

Last Answer : (D) The ability of a material to fracture without appreciable deformation is called its ductility

Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C

Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Last Answer : (A) Applies to elastic deformation

In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Description : In cold working of metal as compared to its hot working (A) Cracks and blow holes are eliminated (B) Ductility and impact strength improves (C) Appreciable strain hardening is produced (D) Yield stress, hardness and fatigue strength is not at all affected

Last Answer : (C) Appreciable strain hardening is produced

The temperature at which new grains are formed in the metal is called the __________ temperature. (A) Eutectic (B) Recrystallisation (C) Upper critical (D) Lower critical

Description : The temperature at which new grains are formed in the metal is called the __________ temperature. (A) Eutectic (B) Recrystallisation (C) Upper critical (D) Lower critical

Last Answer : (B) Recrystallisation

Which of the following terminology is used for the temperature at which new grains are formed in a metal? (A) Eutectic temperature (B) Lower critical temperature (C) Recrystallisation temperature (D) Upper critical temperature

Description : Which of the following terminology is used for the temperature at which new grains are formed in a metal? (A) Eutectic temperature (B) Lower critical temperature (C) Recrystallisation temperature (D) Upper critical temperature

Last Answer : Recrystallisation temperature

Recrystallisation temperature of steel is __________ °C. (A) 50 (B) 300 (C) 500 (D) 800

Description : Recrystallisation temperature of steel is __________ °C. (A) 50 (B) 300 (C) 500 (D) 800

Last Answer : (D) 800

There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Last Answer : b) False

The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Description : The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Last Answer : (B) Flexibility

The deformation of a solid when stress is applied is called a) Strain b) Elasticity c) Rigidity d) Pressure

Description : The deformation of a solid when stress is applied is called a) Strain b) Elasticity c) Rigidity d) Pressure

Last Answer : a) Strain

The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these

Description : The deformation per unit length is called (a) Strain (b) Stress (c) Elasticity (d) None of these

Last Answer : (a) Strain

Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

Transformer cores are normally made from (A) Soft ferrites (B) High purity iron (C) Grain oriented Fe-Si alloy (D) Al-Ni-Co alloy

Description : Transformer cores are normally made from (A) Soft ferrites (B) High purity iron (C) Grain oriented Fe-Si alloy (D) Al-Ni-Co alloy

Last Answer : (C) Grain oriented Fe-Si alloy

Corrosion rate cannot be lowered by reducing the __________ of the corroding medium. (A) Concentration (B) Velocity (C) Temperature (D) None of these

Description : Corrosion rate cannot be lowered by reducing the __________ of the corroding medium. (A) Concentration (B) Velocity (C) Temperature (D) None of these

Last Answer : (A) Concentration

Keeping other parameters constant brake power of diesel engine can be increased by (a) Decreasing the density of intake air (b) Increasing the temperature of intake air (c) Increasing the pressure of intake air (d) Decreasing the pressure of intake air

Description : Keeping other parameters constant brake power of diesel engine can be increased by (a) Decreasing the density of intake air (b) Increasing the temperature of intake air (c) Increasing the pressure of intake air (d) Decreasing the pressure of intake air

Last Answer : Ans : c

Which of the following phenomenon/ phenomena is/are diffusion controlled? (A) Dislocation climb (B) Cross-slip (C) Twinning (D) Recrystallisation

Description : Which of the following phenomenon/ phenomena is/are diffusion controlled? (A) Dislocation climb (B) Cross-slip (C) Twinning (D) Recrystallisation

Last Answer : (D) Recrystallisation

Assuming all other parameters remain constant, what happens to the pressure of a gas when the volume of the gas is increased? w) increases x) decreases y) fluctuates sinusoidally z) remains the same

Description : Assuming all other parameters remain constant, what happens to the pressure of a gas when the volume of the gas is increased? w) increases x) decreases y) fluctuates sinusoidally z) remains the same

Last Answer : ANSWER: X -- DECREASES

Hot & cold working of material causes its __________ deformation. (A) Visco-elastic (B) Isotropic (C) Elastic (D) Plastic

Description : Hot & cold working of material causes its __________ deformation. (A) Visco-elastic (B) Isotropic (C) Elastic (D) Plastic

Last Answer : (D) Plastic

If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its resonant frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Description : If the length of a Hertz dipole is decreased A. its resonant frequency will be lowered its distributed inductance will be increased B. its distributed inductance will be decreased C. its ... frequency will be increased D. its distributed capacitance between the antenna and ground will be increased.

Last Answer : C. its resonant frequency will be increased

In an induction machine, if the air gap increased a) Speed will be reduced b) Efficiency will be improved c) Power factor will be lowered d) Breakdown torque will be reduced

Description : In an induction machine, if the air gap increased a) Speed will be reduced b) Efficiency will be improved c) Power factor will be lowered d) Breakdown torque will be reduced

Last Answer : Ans: Power factor will be lowered

10 years-old boy looses a permanent mandibular molar; what is affected: A. Teeth adjacent to extracted teeth B. Teeth on both arches on same side C. The remaining teeth in the mouth D. Teeth directly opposite to the extracted tooth E. Teeth on the same quadrant

Description : 10 years-old boy looses a permanent mandibular molar; what is affected: A. Teeth adjacent to extracted teeth B. Teeth on both arches on same side C. The remaining teeth in the mouth D. Teeth directly opposite to the extracted tooth E. Teeth on the same quadrant

Last Answer : C. The remaining teeth in the mouth

Dislocation cross-slip is difficult in those materials, which have (A) Large number of slip systems (B) High work hardening rate (C) Coarse grain size (D) Low stacking fault energy

Description : Dislocation cross-slip is difficult in those materials, which have (A) Large number of slip systems (B) High work hardening rate (C) Coarse grain size (D) Low stacking fault energy

Last Answer : (D) Low stacking fault energy

If the evaporator temperature of a plant is lowered, keeping the condenser temperature constant, the h.p. of compressorrequired will be (a) same (b) more (c) less (d) more/less depending on rating

Description : If the evaporator temperature of a plant is lowered, keeping the condenser temperature constant, the h.p. of compressorrequired will be (a) same (b) more (c) less (d) more/less depending on rating

Last Answer : Ans: b

If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Description : If the temperature of intake air in internal combustion engine is lowered, the efficiency will a. increase b. decrease c. remains same d. increases upto certain limit and then decrease

Last Answer : ANSWER a. increase

The hardenability of steel decreases with (A) Decrease in dislocation density (B) Increase in solutionising temperature (C) Increase in strength (D) Decrease in grain size

Description : The hardenability of steel decreases with (A) Decrease in dislocation density (B) Increase in solutionising temperature (C) Increase in strength (D) Decrease in grain size

Last Answer : D) Decrease in grain size

A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co￾efficient for air will vary in the ratio of (A) 2 (B) 2 0.8 (C) 2 0.2 (D) 2 0.5

Description : A single pass air heater is connected to a two pass unit. For the air flow rate and other conditions remaining the same, the film heat transfer co￾efficient for air will vary in the ratio of (A) 2 (B) 2 0.8 (C) 2 0.2 (D) 2 0.5

Last Answer : (B) 2 0.8

As the temperature is lowered towards the absolute zero, the value of ∂(∆F)/∂T, then approaches (A) Unity (B) Zero (C) That of the heat of reaction (D) Infinity

Description : As the temperature is lowered towards the absolute zero, the value of ∂(∆F)/∂T, then approaches (A) Unity (B) Zero (C) That of the heat of reaction (D) Infinity

Last Answer : B) Zero

As the temperature is lowered towards the absolute zero, the value of the quantity (∂∆F/∂T) approaches (A) Zero (B) Unity (C) Infinity (D) None of these

Description : As the temperature is lowered towards the absolute zero, the value of the quantity (∂∆F/∂T) approaches (A) Zero (B) Unity (C) Infinity (D) None of these

Last Answer : (A) Zero

Boiling point of water gets lowered at high altitudes (e.g., hills), because (A) Temperature is low (B) Atmospheric pressure is low (C) Atmospheric pressure is high (D) None of these

Description : Boiling point of water gets lowered at high altitudes (e.g., hills), because (A) Temperature is low (B) Atmospheric pressure is low (C) Atmospheric pressure is high (D) None of these

Last Answer : Option B

Presence of SO2 in furnace gases attacks the ferrous metal by way of (A) Accelerating the rate of scaling (B) Causing metal embrittlement (C) Attacking the grain boundaries; particularly severe on low carbon and nickel bearing steels at high temperature (D) All (A), (B) and (C)

Description : Presence of SO2 in furnace gases attacks the ferrous metal by way of (A) Accelerating the rate of scaling (B) Causing metal embrittlement (C) Attacking the grain boundaries; particularly severe on low carbon and nickel bearing steels at high temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Description : Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Last Answer : (b) 50 percent

. A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid. (A) Newtonian (B) Non-Newtonian (C) Ideal (D) Incompressible

Description : . A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid. (A) Newtonian (B) Non-Newtonian (C) Ideal (D) Incompressible

Last Answer : (A) Newtonian

As per Newton's law of viscosity, the shear stress for a given rate of angular deformation of fluid is proportional to (where, μ = fluid viscosity) (A) 1/μ (B) μ (C) μ 2 (D) 1/μ

Description : As per Newton's law of viscosity, the shear stress for a given rate of angular deformation of fluid is proportional to (where, μ = fluid viscosity) (A) 1/μ (B) μ (C) μ 2 (D) 1/μ

Last Answer : (B) μ

Newton's law of viscosity relates the (A) Shear stress and velocity (B) Velocity gradient and pressure intensity (C) Shear stress and rate of angular deformation in a fluid (D) Pressure gradient and rate of angular deformation

Description : Newton's law of viscosity relates the (A) Shear stress and velocity (B) Velocity gradient and pressure intensity (C) Shear stress and rate of angular deformation in a fluid (D) Pressure gradient and rate of angular deformation

Last Answer : (C) Shear stress and rate of angular deformation in a fluid

In a heat exchanger with steam outside the tubes, a liquid gets heated to 45°C, when its flow velocity in the tubes is 2 m/s. If the flow velocity is reduced to 1 m/s, other things remaining the same, the temperature of the exit liquid will be (A) Less than 45°C (B) More than 45°C (C) Equal to 45°C (D) Initially decreases and remains constant thereafter

Description : In a heat exchanger with steam outside the tubes, a liquid gets heated to 45°C, when its flow velocity in the tubes is 2 m/s. If the flow velocity is reduced to 1 m/s, other things remaining ... than 45°C (B) More than 45°C (C) Equal to 45°C (D) Initially decreases and remains constant thereafter

Last Answer : (B) More than 45°C

When the continuing auditor intends to use information about the entity and its environment obtained in prior periods, the auditor shoulda. Assess control risk as "high" for theassertions affected by the prior-periodinformation.b. Seek permission with the client in usingthe prior period information obtained bythe auditor.c. Determine whether changes haveoccurred that may affect therelevance of such information in thecurrent audit.d. Determine whether to equitably reducethe audit fee due to lower audit effortexpended during the engagement

Description : When the continuing auditor intends to use information about the entity and its environment obtained in prior periods, the auditor should a. Assess control risk as "high" for the assertions ... whether to equitably reduce the audit fee due to lower audit effort expended during the engagement

Last Answer : Determine whether changes have occurred that may affect the relevance of such information in the current audit.

Roughness index of roads, is expressed as (A) Size of the stone on the pavement (B) Number of patches on the pavement (C) Cumulative deformation of surface per horizontal distance (D) Type of the road surface

Description : Roughness index of roads, is expressed as (A) Size of the stone on the pavement (B) Number of patches on the pavement (C) Cumulative deformation of surface per horizontal distance (D) Type of the road surface

Last Answer : Answer: Option C

Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Description : Which of the following problem arises in D.C. motors which are fed from thyristor bridge circuits ? (a) Increased I R losses (b) Increased core losses (c) Poor commutation (d) Change in motor parameters (e) All of the above

Last Answer : (e) All of the above

Which of the following statements concerning the specific gravity of a battery electrolyte is true? A. The electrolyte becomes less dense when it is cooled. B. The specific gravity reading is lowered when the electrolyte is heated. C. The most accurate hydrometer reading is obtained immediately after water is added. D. The temperature does not affect the specific gravity of the electrolyte.

Description : Which of the following statements concerning the specific gravity of a battery electrolyte is true? A. The electrolyte becomes less dense when it is cooled. B. The specific gravity reading is lowered ... water is added. D. The temperature does not affect the specific gravity of the electrolyte.

Last Answer : Answer: B

Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) The damping capacity of a material is due to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Description : Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) ... to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Last Answer : Option B