Hot & cold working of material causes its __________ deformation. (A) Visco-elastic (B) Isotropic (C) Elastic (D) Plastic

Hot & cold working of material causes its __________ deformation. (A) Visco-elastic
(B) Isotropic
(C) Elastic
(D) Plastic
by

1 Answer

Answer :

(D) Plastic
by

Related questions

The behaviour of visco-elastic material is time dependent. This behaviour is common in __________ materials. (A) Non-crystalline solid (B) Crystalline (C) Rubbery (D) Non-crystalline organic polymeric

Description : The behaviour of visco-elastic material is time dependent. This behaviour is common in __________ materials. (A) Non-crystalline solid (B) Crystalline (C) Rubbery (D) Non-crystalline organic polymeric

Last Answer : (D) Non-crystalline organic polymeric

Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Description : Visco-elastic behaviour exhibited by plastics is a __________ like behaviour. (A) Solid (B) Liquid (C) Combination of solid & liquid (D) Neither solid nor liquid

Last Answer : (C) Combination of solid & liquid

The spring operates (A) Within plastic limit (B) Within elastic limit (C) Within elasto-plastic limit (D) Within visco-elastic limit

Description : The spring operates (A) Within plastic limit (B) Within elastic limit (C) Within elasto-plastic limit (D) Within visco-elastic limit

Last Answer : (B) Within elastic limit

Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) The damping capacity of a material is due to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Description : Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) ... to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Last Answer : Option B

If a material has identical properties in all directions, it is called (a) Elastic (b) Plastic (c) Isotropic (d) Homogeneous

Description : If a material has identical properties in all directions, it is called (a) Elastic (b) Plastic (c) Isotropic (d) Homogeneous

Last Answer : (c) Isotropic

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Description : The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Last Answer : Ductile

Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco-elastic material, stress-strain relation is dependent on time (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Description : Pick up the correct statement from the following: (A) The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance (B) In visco ... (C) An orthotropic material has different properties in three mutually perpendicular directions (D) All the above

Last Answer : (D) All the above

Visco-elastic behaviour of materials which is time dependent is common in (A) Plastics (B) Crystalline solid (C) Non-crystalline solids (D) Non-crystalline organic polymer

Description : Visco-elastic behaviour of materials which is time dependent is common in (A) Plastics (B) Crystalline solid (C) Non-crystalline solids (D) Non-crystalline organic polymer

Last Answer : (D) Non-crystalline organic polymer

Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Last Answer : Answer: Option D

A member which does not regain its original shape after removed of load producing deformation is said (A) Plastic (B) Elastic (C) Rigid (D) None of these

Description : A member which does not regain its original shape after removed of load producing deformation is said (A) Plastic (B) Elastic (C) Rigid (D) None of these

Last Answer : (A) Plastic

Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Description : Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Last Answer : ductile substances

Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Last Answer : d) All of the mentioned

Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)? (A) E = 2G (1 + v) (B) E = G (1 + v) (C) E = G (1 + v)/2 (D) E = 2G (1 + 2v)

Description : Which of the following relationships is correct for relating the three elastic constants of an isotropic elastic material (where, E = Young's modulus, G = Modulus of rigidity or shear modulus v = Poisson's ratio)? (A) E = 2G (1 + v) (B) E = G (1 + v) (C) E = G (1 + v)/2 (D) E = 2G (1 + 2v)

Last Answer : (A) E = 2G (1 + v)

Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does not occur (C) Initiation of crack occurs on the surface of the machine part (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface

Description : Which of the following is not a characteristic observed in material failure by fatigue fracture? (A) Plastic deformation of material does not occur (B) Initiation of crack from below the surface does ... (D) Presence of both rough & smooth zone with conchoidal markings in smooth zone of the surface

Last Answer : Option B

Isotropic materials have the same __________ in all directions. (A) Induced stresses (B) Density (C) Elastic properties (D) Thermal properties

Description : Isotropic materials have the same __________ in all directions. (A) Induced stresses (B) Density (C) Elastic properties (D) Thermal properties

Last Answer : C) Elastic properties

In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. normal stress varies linearly in the material c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Description : In a simple bending theory, one of the assumption is that the material of the beam is isotropic. This assumption means that the a. normal stress remains constant in all directions b. ... c. elastic constants are same in all the directions d. elastic constants varies linearly in the material

Last Answer : c. elastic constants are same in all the directions

Is it true Elastic deformation occurs when a material deforms as stress is applied?

Description : Is it true Elastic deformation occurs when a material deforms as stress is applied?

Last Answer : Yes

For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure does not fail (a) Firstly Maximum Principal Theory (b) Secondly Maximum Shear Stress Theory (c) Thirdly Maximum Principal Energy Theory (d) None

Description : For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure does not fail (a) Firstly Maximum Principal Theory (b) Secondly Maximum Shear Stress Theory (c) Thirdly Maximum Principal Energy Theory (d) None

Last Answer : (a) Firstly Maximum Principal Theory

For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure fails (a) Firstly Maximum Principal Theory (b) Secondly Maximum Principal strain Theory (c) Thirdly Maximum Principal Energy Theory (d) None

Description : For a homogeneous & isotropic body under hydrostatic pressure, which theory of elastic failure fails (a) Firstly Maximum Principal Theory (b) Secondly Maximum Principal strain Theory (c) Thirdly Maximum Principal Energy Theory (d) None

Last Answer : (c) Thirdly Maximum Principal Energy Theory

Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Description : Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Last Answer : (B) Toughness

Pick out the correct statement. (A) Stainless steel is nothing but chromium coated steel (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal (C) Plastic deformation of a material is its temporary distortion under the action of applied stress (D) Rusting of iron is not electrochemical in nature

Description : Pick out the correct statement. (A) Stainless steel is nothing but chromium coated steel (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal (C) ... its temporary distortion under the action of applied stress (D) Rusting of iron is not electrochemical in nature

Last Answer : (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal

The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Description : Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Last Answer : (C) Creep

…. is the property of a material which enables it to resist plastic deformation.

Description : …. is the property of a material which enables it to resist plastic deformation.

Last Answer : …. is the property of a material which enables it to resist plastic deformation. (A) elasticity (B) plasticity (C) hardness (D) ductility

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength

Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C

Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Last Answer : (A) Applies to elastic deformation

The materials which have the same elastic properties in all directions, are called (A) Isotropic (B) Brittle (C) Homogeneous (D) Hard

Description : The materials which have the same elastic properties in all directions, are called  (A) Isotropic  (B) Brittle  (C) Homogeneous  (D) Hard 

Last Answer : (A) Isotropic 

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is proportional to the age of the member at the time of loading. (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

__________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning

Description : __________ of a material results, when its strength is increased & ductility is decreased by heating at a relatively lower temperature after cold working. (A) Solid solution hardening (B) Screw dislocation (C) Strain ageing (D) Twinning

Last Answer : (C) Strain ageing

A material no longer behaves elastically beyond (A) Plastic limit (B) Limiting load (C) Elastic limit (D) Breaking load

Description : A material no longer behaves elastically beyond (A) Plastic limit (B) Limiting load (C) Elastic limit (D) Breaking load

Last Answer : (C) Elastic limit

Which of the following is the most elastic material? (A) Plastic (B) Glass (C) Steel (D) Rubber

Description : Which of the following is the most elastic material? (A) Plastic (B) Glass (C) Steel (D) Rubber

Last Answer : (C) Steel

Pick out the wrong statement. (A) Bronze is an alloy of copper & tin (B) Brass is an alloy of copper & zinc (C) The alloy named 'German silver' does not contain any silver (D) The ability of a material to fracture without appreciable deformation is called its ductility

Description : Pick out the wrong statement. (A) Bronze is an alloy of copper & tin (B) Brass is an alloy of copper & zinc (C) The alloy named 'German silver' does not contain any silver (D) The ability of a material to fracture without appreciable deformation is called its ductility

Last Answer : (D) The ability of a material to fracture without appreciable deformation is called its ductility

An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Description : An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Last Answer : (A) Sewage sludge

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Description : The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Last Answer : Option C

All thermoplastic, thermosetting & elastic materials can be processed in a extrusion machine, however it cannot be used for the production of plastic (A) Filaments (B) Pipes (C) Buckets (D) Tubings

Description : All thermoplastic, thermosetting & elastic materials can be processed in a extrusion machine, however it cannot be used for the production of plastic (A) Filaments (B) Pipes (C) Buckets (D) Tubings

Last Answer : (C) Buckets

Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these

Description : Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these

Last Answer : (C) Limit of proportionality

The addition of antimony in tin-based alloys improves its (A) Rupture strength and hot hardness (B) Impact strength and bonding strength (C) Deformation resistance (D) Wear resistance

Description : The addition of antimony in tin-based alloys improves its (A) Rupture strength and hot hardness (B) Impact strength and bonding strength (C) Deformation resistance (D) Wear resistance

Last Answer : (C) Deformation resistance

At ‘yield point’ of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become plastic C. even the plastic stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Description : At yield point' of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become ... stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Last Answer : the load has already exceeded the elastic limit and the material has become plastic

The stress at which extension of a material takes place more quickly as compared to the increase in load, is called (A) Elastic point (B) Plastic point (C) Breaking point (D) Yielding point

Description : The stress at which extension of a material takes place more quickly as compared to the increase in load, is called (A) Elastic point (B) Plastic point (C) Breaking point (D) Yielding point

Last Answer : (D) Yielding point

The limit beyond which the material does not behave elastically is known as (a) Proportional limit (b) Elastic limit (c) Plastic limit (d) Yield Point

Description : The limit beyond which the material does not behave elastically is known as (a) Proportional limit (b) Elastic limit (c) Plastic limit (d) Yield Point

Last Answer : (b) Elastic limit

Every material obeys the Hooke’s law within (a) Elastic limit (b) Plastic limit (c) Limit of proportionality (d) None of these

Description : Every material obeys the Hooke’s law within (a) Elastic limit (b) Plastic limit (c) Limit of proportionality (d) None of these

Last Answer : c) Limit of proportionality