The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is
(A) More
(B) Less
(C) Same
(D) More but less than the diameter of bolt
by

1 Answer

Answer :

(A) More
by

Related questions

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Last Answer : (B) Making shank diameter equal to core diameter of threads

The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it. (A) Tension (B) Shear (C) Compression (D) Bending & tension

Description : The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it. (A) Tension (B) Shear (C) Compression (D) Bending & tension

Last Answer : Option A

When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size

Description : The inner diameter of washer is (A) Equal to the nut size (B) More than the nut size (C) Less than the nut size (D) Independent of the nut size

Last Answer : (B) More than the nut size

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

Front load washers cost so much more than top load washers. What are the benefits of the front load washer since it is more costly?

Description : Front load washers cost so much more than top load washers. What are the benefits of the front load washer since it is more costly?

Last Answer : Front load washers will use much less water than a conventional model. They also typically require less soap. Some believe that front load washers clean more thoroughly in that the clothes repeatedly hit the water, instead of just being immersed in it.

A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Description : A washer is specified by (A) Outer diameter (B) Inner diameter (C) Thickness (D) Mean diameter

Last Answer : (B) Inner diameter

Screws are specified by their __________ diameters. (A) Minor (B) Major (C) Pitch (D) None of these

Description : Screws are specified by their __________ diameters. (A) Minor (B) Major (C) Pitch (D) None of these

Last Answer : (B) Major

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

A packed tower compared to a plate tower for a particular mass transfer operation (A) Incurs smaller pressure drop (B) Allows installation of cooling coils (C) Is less costly when built in large sizes/diameters (D) Is more suitable, if suspended solids are present in fluid stream

Description : A packed tower compared to a plate tower for a particular mass transfer operation (A) Incurs smaller pressure drop (B) Allows installation of cooling coils (C) Is less costly when built in large sizes/diameters (D) Is more suitable, if suspended solids are present in fluid stream

Last Answer : (A) Incurs smaller pressure drop

Which of the following fastening devices has its both ends threaded? (A) Bolt (B) Stud (C) Set screw (D) Split nut

Description : Which of the following fastening devices has its both ends threaded? (A) Bolt (B) Stud (C) Set screw (D) Split nut

Last Answer : (B) Stud

Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Description : Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Last Answer : Option B

Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Description : Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Last Answer : Option B

The diameter of earth is 12,757 kilometers the diameter of satum is 120,664 the diameters of uranus is 51,499 is the sum of these three plantes diameters more or less than jupiter diameter of 142,804 kilometers by how much answer?

Description : The diameter of earth is 12,757 kilometers the diameter of satum is 120,664 the diameters of uranus is 51,499 is the sum of these three plantes diameters more or less than jupiter diameter of 142,804 kilometers by how much answer?

Last Answer : 2

The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Last Answer : Answer: Option C

A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Description : A rolling contact bearing is specified as X307. Calculate the bearing diameter. (a) 35 mm (b) 28 mm (c) 21 mm (d) 7 mm

Last Answer : (a) 35 mm

The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Description : The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Last Answer : (B) Have different diameters

Why don't americans have butt-hole washers in bathrooms?

Description : Why don't americans have butt-hole washers in bathrooms?

Last Answer : It is a little known fact that President Jimmy Carter in 1977 in his first month in office, wanted to sign a bill mandating outhouses for all Americans and due to a strong Republican push ... a bill was passed that any indoor plumbing was limited to toilets only .virtually outlawing fancy bidets.

I forgot to put water in pressure cooker while cooking , do u have the part that i need to replace It is some kind of nut n bolt near to the wishtle?

Description : I forgot to put water in pressure cooker while cooking , do u have the part that i need to replace It is some kind of nut n bolt near to the wishtle?

Last Answer : Check with Sears parts and Repair in your local area. If they dont have it thet can order it for you. Just check for your model number at the bottom of your pressure cooker.. Check with Sears parts ... can order it for you. Just check for your model number at the bottom of your pressure cooker..

In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Description : In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Last Answer : b) False

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (B) h = 0.25 dc

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Description : Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Last Answer : (D) All the above

(2) experience collision less frequently Explanation: When an electric field is applied, both the valence electrons and the free electrons move in the same direction. The hole direction is opposite to that of valence electron but the mobility is the same. Even for the same electric field, valence electrons cannot move as freely as the free electrons because its movement is restricted due to collisions. Therefore, the velocity of valence electrons is less compared to free electrons. In other words, the velocity of holes is less compared to free electrons. This means mobility is also less for a hole compared to free electron.

Description : (2) experience collision less frequently Explanation: When an electric field is applied, both the valence electrons and the free electrons move in the same direction. The hole direction is opposite to that ... to free electrons. This means mobility is also less for a hole compared to free electron.

Last Answer : Carbon dioxide is called a greenhouse gas because - (1) its concentration remains always higher than other gases (2) it is used in photosynthesis (3) it absorbs infrared radiation (4) it emits visible radiation

The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Last Answer : Answer: Option C

is a circular concave revolving steel plate using for cutting and inverting the soil. a. Gang bolt. c. Disc b. Bearing d. None

Description : is a circular concave revolving steel plate using for cutting and inverting the soil. a. Gang bolt. c. Disc b. Bearing d. None

Last Answer : Bearing 

is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Description : is essential to counter act the and thrust of gang due to soil thrust. a. Gang c. Spacer b. Bearing. d. Gang bolt

Last Answer : Bearing.

The flanked tube mounted on the gang bold between every two disc to prevent the lateral movement of the disc on the shaft is called............ a. Bearing. c. Gang bolt b. Gang. d. Spool

Description : The flanked tube mounted on the gang bold between every two disc to prevent the lateral movement of the disc on the shaft is called............ a. Bearing. c. Gang bolt b. Gang. d. Spool

Last Answer : Spool

is essential to counter act the end thrust of gang due to soil thrust.. A) Spool. C ) Gang B) Bearing. D) Gang bolt

Description : is essential to counter act the end thrust of gang due to soil thrust.. A) Spool. C ) Gang B) Bearing. D) Gang bolt

Last Answer : Bearing

For specified tube outside diameter, higher BWG means higher (A) Tube thickness (B) Cross-sectional area (C) Weight per unit length (D) None of these

Description : For specified tube outside diameter, higher BWG means higher (A) Tube thickness (B) Cross-sectional area (C) Weight per unit length (D) None of these

Last Answer : (B) Cross-sectional area

Multimode step-index fibers have relatively large core diameters and large numerical apertures. These provide what benefit?

Description : Multimode step-index fibers have relatively large core diameters and large numerical apertures. These provide what benefit?

Last Answer : Make it easier to couple light from a light-emitting diode (LED) into the fiber.

The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable

Description : The equivalent diameter for the annulus of a double pipe heat exchanger, whose inner pipe has fins on the outside is __________ compared to the same size pipes without fins. (A) More (B) Less (C) Same (D) Unpredictable

Last Answer : (B) Less

Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the possibility of tower wall collapse (B) Packed towers are preferred over plate towers for handling corrosive and foamy liquids (C) Diameter of randomly packed tower is normally more than 1.2 metres (D) Due to uneven supply and improper distribution of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Description : Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the ... of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Last Answer : (C) Diameter of randomly packed tower is normally more than 1.2 metres

What nut has a hole and is squishy? -Riddles

Description : What nut has a hole and is squishy? -Riddles

Last Answer : Doughnut

The shock absorbing capacity of bolt can be increased by making the shank diameter ________ the root diameter. a) Lesser than b) Equal to c) Greater than d) No effect

Description : The shock absorbing capacity of bolt can be increased by making the shank diameter ________ the root diameter. a) Lesser than b) Equal to c) Greater than d) No effect

Last Answer : b) Equal to

Pick out the wrong statement. (A) Nitrogen is normally supplied in fertiliser either in Ammoniacal or the nitrate form, from which the soil takes it up in the form of ammonium ions ornitrate ions and forms amino acids(B) Calcium present in the fertiliser helps in correcting the soil acidity(C) Particle size range of a good granular fertiliser is 10-15 mesh and itcontains less moisture as compared to finely divided powder form of fertiliser(D) Ammonium nitrate fertiliser is obtained as a by-product in an integratedsteel plant having by-product coke ovens

Description : Pick out the wrong statement. (A) Nitrogen is normally supplied in fertiliser either in Ammoniacal or the nitrate form, from which the soil takes it up in the form of ammonium ions ornitrate ... nitrate fertiliser is obtained as a by-product in an integrated steel plant having by-product coke ovens

Last Answer : (D) Ammonium nitrate fertiliser is obtained as a by-product in an integrated steel plant having by-product coke ovens

The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1

Description : The length to diameter ratio for a square bearing is (A) More than 1 (B) Less than 1 (C) 8 (D) 1

Last Answer : (D) 1

The length to diameter ratio for a short bearing is (A) More than 1 (B) Less than 1 (C) 8

Description : The length to diameter ratio for a short bearing is (A) More than 1 (B) Less than 1 (C) 8

Last Answer : (B) Less than 1

If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm

Description : If core diameter of bolt is 13.8cm the it’s nominal diameter is given by? a) 17.27mm b) 15.34mm c) 14.67mm d) 16.34mm

Last Answer : a) 17.27mm

The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Description : The shock absorbing capacity of bolts can be increased by a) Increasing the shank diameter b) Decreasing the length of shank portion of bolt c) Increase the shank diameter and decreasing the length of shank d) None of the listed

Last Answer : d) None of the listed

The shock absorbing capacity of a bolt can be increased by (A) Increasing stress in shank (B) Increasing stress in core diameter of threads (C) Decreasing stress in shank (D) Decreasing stress in core diameter of threads

Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing stress in shank (B) Increasing stress in core diameter of threads (C) Decreasing stress in shank (D) Decreasing stress in core diameter of threads

Last Answer : (A) Increasing stress in shank

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

Resilience of a bolt can be increased by increasing its (A) Length (B) Shank diameter (C) Head diameter (D) None of these

Description : Resilience of a bolt can be increased by increasing its (A) Length (B) Shank diameter (C) Head diameter (D) None of these

Last Answer : (A) Length