Which of the following fastening devices has its both ends threaded? (A) Bolt (B) Stud (C) Set screw (D) Split nut

Which of the following fastening devices has its both ends threaded? (A) Bolt
(B) Stud
(C) Set screw
(D) Split nut
by

1 Answer

Answer :

(B) Stud
by

Related questions

Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Description : Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Last Answer : Option B

Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Description : Which of the following fastening devices has a head at one end and a nut fitted to the other? (A) Bolt (B) Stud (C) Top bolt (D) None of these

Last Answer : Option B

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Description : Which type of screw fasteners are threaded through out its length? a. Cap screws b. Set screws c. Studs d. Tap bolt

Last Answer : b. Set screws

If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Description : If a fastener is threaded into a tapped hole, then the fastener is likely to be called as a) Screw b) Bolt c) Washer d) Screw or bolt

Last Answer : a) Screw

The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Description : The shear plane in case of bolts should (a) be across threaded portion of shank (b) be parallel to axis of bolt (c) be normal to threaded portion of shank (d) never be across the threaded portion (e) none of the above.

Last Answer : (d) never be across the threaded portion

The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Description : The maximum efficiency of a square threaded screw is (A) (1 - sinφ)/ (1 + sinφ) (B) (1 + sinφ)/ (1 - sinφ)s (C) (1 - sinφ)/ (1 + cosφ) (D) (1 + cosφ)/ (1 - sinφ)

Last Answer : (A) (1 - sinφ)/ (1 + sinφ)

Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Description : Screw jack can be adjusted no more than? a. 300mm (12 inches) of threaded length showing b. 2/3 of the total threaded length showing c. 150mm (6 inches) of threaded length showing d. 1/3 of the total threaded length showing

Last Answer : b. 2/3 of the total threaded length showing

The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Description : The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Last Answer : (A) More

The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it. (A) Tension (B) Shear (C) Compression (D) Bending & tension

Description : The bolt is subjected to __________ when the nut is tightened by putting the washer beneath it. (A) Tension (B) Shear (C) Compression (D) Bending & tension

Last Answer : Option A

I forgot to put water in pressure cooker while cooking , do u have the part that i need to replace It is some kind of nut n bolt near to the wishtle?

Description : I forgot to put water in pressure cooker while cooking , do u have the part that i need to replace It is some kind of nut n bolt near to the wishtle?

Last Answer : Check with Sears parts and Repair in your local area. If they dont have it thet can order it for you. Just check for your model number at the bottom of your pressure cooker.. Check with Sears parts ... can order it for you. Just check for your model number at the bottom of your pressure cooker..

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Description : In nut and bolt fastener, nut is generally held stationary while bolt is rotated. a) True b) False

Last Answer : b) False

The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Description : The shock absorbing capacity of a bolt can be increased by (A) Increasing shank diameter (B) Making shank diameter equal to core diameter of threads (C) Using castle nut in place of ordinary hexagonal nut (D) Using a washer

Last Answer : (B) Making shank diameter equal to core diameter of threads

When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the threads of bolt are subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (B) h = 0.25 dc

When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : When a nut is tightened by placing a washer below it, the shank of bolt is subjected to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (C) Tensile stress

Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Description : Setscrews are (A) Similar to tap bolts except that a greater variety of shapes of heads are available (B) Slotted for screw driver and generally used with a nut (C) Used to prevent relative motion between parts (D) Similar to studs

Last Answer : (C) Used to prevent relative motion between parts

While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Description : While designing screw threads, adequate length of engaged threads between the screw and nut is provided so as to prevent failure of threads due to (A) Direct shear stress (B) Torsional shear stress (C) Tensile stress (D) Compressive stress

Last Answer : (A) Direct shear stress

Explain following constructional details of CNC machines with neat sketches. (i) Hydrostatic slideways (ii) Recirculating ball screw and nut

Description : Explain following constructional details of CNC machines with neat sketches. (i) Hydrostatic slideways (ii) Recirculating ball screw and nut

Last Answer : (i) Hydrostatic slideways: In hydrostatic slideways, air or oil is pumped into small pockets or cavities into the carrieage or slides which are in contact with the slide ways. The pressure of ... nut strokes on the screw shaft, the balls repeat the same recirculation inside the return tube. 

The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are operated by the same relay coil B. screw connections are on terminal board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Description : The vertical dotted line connecting the small circular symbols at coordinates '05L', '09L', '13L', '21L', '25L', etc., shown in the illustration, indicate that all _______________. EL-0100 A. contacts are ... board 'TB2' C. wires are grounded at both ends of the line D. wires have a common shield

Last Answer : Answer: B

Whitcome Judson in 1891 invented what for fastening shoes?

Description : Whitcome Judson in 1891 invented what for fastening shoes?

Last Answer : Zip Fastener

what is a fastening?

Description : what is a fastening?

Last Answer : The answer is rivet.

What is the fastening method of your foot?

Description : What is the fastening method of your foot?

Last Answer : Need answer

Cotter joint is a permanent fastening. a) true b) false

Description : Cotter joint is a permanent fastening. a) true b) false

Last Answer : b) false

Whitcome Judson in 1891 invented what for fastening shoes

Description : Whitcome Judson in 1891 invented what for fastening shoes 

Last Answer : Zip Fastener

How should I tackle the multiple split-ends of my hair?

Description : How should I tackle the multiple split-ends of my hair?

Last Answer : A really good conditioner and always brush from the bottom up. Don’t pull any tangles out gently loosen them from the bottom.

What can I put in my hair that will get rid of split ends?

Description : What can I put in my hair that will get rid of split ends?

Last Answer : answer:A pair of scissors. Then, stop fucking with it. Only shampoo your head to the base of your neck, condition all your hair. Stop using heat and damaging chemicals, resist styling as much as ... those in high school when I had classic length' hair. Once every two weeks, alternating treatments.

What can I do for my split ends?

Description : What can I do for my split ends?

Last Answer : Cutting split ends is really the only way to fix them. Trims are helpful of course, but ultimately the hair will continue to split if the damaged hair isn't cut off. Nothing will actually heal your hair, ... decision, those things are hard on your hair pretty as it may look after it's styled. :)

Does Your Hair Grow Faster By Regularly Cutting Your Split-Ends?

Description : Does Your Hair Grow Faster By Regularly Cutting Your Split-Ends?

Last Answer : Your hair is really dead proteins. Cutting the tips of it won't stimulate new growth, because the tissue is dead and can't communicate, even if it may be theoretically possible. No technique or cream has ever ... to back that up. Human hair grows at about half an inch per month, or 6 inches a year.

I have long hair. My hair have split ends. Is it possible to remove splits end any how?

Description : I have long hair. My hair have split ends. Is it possible to remove splits end any how?

Last Answer : Haircare is important and especially if you have long hair. You will need to have a good brush to use and most people suggest that brushing your hair will cause split ends. Conditioning your hair and ... much sun. visit the beauty shop and have the split ends trimmed to keep your hair healthy.

What is the best hair care product to use when you have split ends?

Description : What is the best hair care product to use when you have split ends?

Last Answer : Use products from Suave and Garnier to strengthen your hair and release its inner beauty

Why do I have so many split ends?

Description : Why do I have so many split ends?

Last Answer : Split ends can happen for a variety of reasons. Dying your hair often and using the high heat setting on you hair dryer contributes to split ends. Your hair can be damaged, either from the ... can cause split ends. Excessive washing with shampoos can strip your hair, which also cause split ends.

How to Repair Split Ends

Description : How to Repair Split Ends

Last Answer : How to Repair Split Ends Do you have small wisps of hair sticking out from the ends of your locks? These are split ends. Not only do they ruin a great hairstyle, but split ends also make your hair ... 't be a problem. Follow these tips so you'll never have to split with your sleek, beautiful hair.

A set of discs are mounted on the i. Gang bolt c) Both a) and b) ii. Arbor bolt. d) Non of the above

Description : A set of discs are mounted on the i. Gang bolt c) Both a) and b) ii. Arbor bolt. d) Non of the above

Last Answer : Both a) and b)

Which type of joints is better when the product is subjected to large vibrations: welded or threaded? a) Welded b) Threaded c) Both have same results d) Depends on the magnitude of the vibrational force

Description : Which type of joints is better when the product is subjected to large vibrations: welded or threaded? a) Welded b) Threaded c) Both have same results d) Depends on the magnitude of the vibrational force

Last Answer : a) Welded

Projection welding & stud welding is categorised as the __________ welding. (A) Pressure (B) Thermit (C) Resistance (D) Arc

Description : Projection welding & stud welding is categorised as the __________ welding. (A) Pressure (B) Thermit (C) Resistance (D) Arc

Last Answer : C) Resistance

Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Last Answer : d) All of the listed

Each set of disk that are mounted on the common shaft is called the………… a. Gang control lever c. Spool b. Gang bolt. d. Gang

Description : Each set of disk that are mounted on the common shaft is called the………… a. Gang control lever c. Spool b. Gang bolt. d. Gang

Last Answer : Gang

An idiot threaded my eyebrows horribly, will they ever grow back?

Description : An idiot threaded my eyebrows horribly, will they ever grow back?

Last Answer : They will. Give it time but they will. And they will grow back same as before. It takes many years of plucking or threading before they won’t come back, and you haven’t done that.

In a single threaded worm and worm wheel the number of teeth on the worm wheel is 60. The diameter of the effort wheel is 12 cm and that of load drum is 8 cm. The velocity ratio will be a.90 b.120 c.60 d.45 e.107 dynes

Description : In a single threaded worm and worm wheel the number of teeth on the worm wheel is 60. The diameter of the effort wheel is 12 cm and that of load drum is 8 cm. The velocity ratio will be a.90 b.120 c.60 d.45 e.107 dynes

Last Answer : a. 90

In a single threaded worm and worm wheel the number of teeth on the worm wheel is 80. The diameter of the effort wheel is 12 cm and that of load drum is 8 cm. The velocity ratio will be a.60 b.45 c.120 d.107 dynes e.90

Description : In a single threaded worm and worm wheel the number of teeth on the worm wheel is 80. The diameter of the effort wheel is 12 cm and that of load drum is 8 cm. The velocity ratio will be a.60 b.45 c.120 d.107 dynes e.90

Last Answer : c. 120

Who invented the threaded Jenny ?

Description : Who invented the threaded Jenny ?

Last Answer : James Hargreaves discovers the thread Jenny.

From which direction should the waist belt be threaded?

Description : I know there are different rules for men than for women, but what are the rules for fastening your belt?

Last Answer : It is customary to fasten the belt from left to right. There are also direct-patterned buckled belts, usually designed to be threaded from left to right. But I think who gets it. The one with the left guarantor is the other way around. 

Do I need threaded or flanged type of vacuum relief valve?

Description : Do I need threaded or flanged type of vacuum relief valve?

Last Answer : You should take your current one off and see what type you have. If you can't take it off, then you should go down to your local parts store and ask them which one your vehicle takes. They have a huge database that typically lists all of the different parts that are needed.

Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets connecting a lifeboat and the vessel's electrical system must have threaded plugs. C. Machinery spaces must contain sufficient outlets for lighting all machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Description : Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets ... machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Last Answer : Answer: A

Threaded joints are non-separable joints. a) True b) False

Description : Threaded joints are non-separable joints. a) True b) False

Last Answer : b) False

Maximum efficiency of a square threaded is given by a) 1-sinǾ/1+sinǾ b) 1+sinǾ/1-sinǾ c) 1-2sinǾ/1+2sinǾ d) 1+2sinǾ/1-2sinǾ

Description : Maximum efficiency of a square threaded is given by a) 1-sinǾ/1+sinǾ b) 1+sinǾ/1-sinǾ c) 1-2sinǾ/1+2sinǾ d) 1+2sinǾ/1-2sinǾ

Last Answer : a) 1-sinǾ/1+sinǾ