The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

The pump impeller and the turbine runner in a hydraulic torque
converter
(A) Have the same diameter
(B) Have different diameters
(C) Are directly coupled
(D) None of these
by

1 Answer

Answer :

(B) Have different diameters
by

Related questions

With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Last Answer : (B) Head varies as the square of speed

At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Description : A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Last Answer : (B) Vaned diffusion casing

For a turbine agitated and baffled tank, operating at low Reynold's number (based on impeller diameter), the power number (Np ) varies with NRe as (A) Np ∝ NRe (B) Np ∝ √NRe (C) Np → constan(D) Np ∝ 1/NRe

Description : For a turbine agitated and baffled tank, operating at low Reynold's number (based on impeller diameter), the power number (Np ) varies with NRe as (A) Np ∝ NRe (B) Np ∝ √NRe (C) Np → constan (D) Np ∝ 1/NRe

Last Answer : (D) Np ∝ 1/NRe

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Last Answer : (A) Density of the liquid

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Description : The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Last Answer : (A) Barometric pressure

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Last Answer : (A) D = 1840 H0.5 /N

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Hydraulic __________ works on the principle of Pascal's law of transmission of fluid pressure. (A) Press (B) Turbine (C) Pump (D) Coupling

Description : Hydraulic __________ works on the principle of Pascal's law of transmission of fluid pressure. (A) Press (B) Turbine (C) Pump (D) Coupling

Last Answer : (A) Press

Turbine impeller (A) Produces only radial current (B) Produces only tangential current (C) Is effective over wide range of viscosities (D) Does not produce tangential current

Description : Turbine impeller (A) Produces only radial current (B) Produces only tangential current (C) Is effective over wide range of viscosities (D) Does not produce tangential current

Last Answer : (C) Is effective over wide range of viscosities

__________ is an example of axial flow impeller. (A) Paddle (B) Turbine (C) Propeller (D) All (A), (B) and (C)

Description : __________ is an example of axial flow impeller. (A) Paddle (B) Turbine (C) Propeller (D) All (A), (B) and (C)

Last Answer : (C) Propeller

Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Description : Two shafts A and B are made of same material. The diameters of shaft A and B are dA and dB respectively. The ratio of torque transmitted by shaft A to that of shaft B will be (A) dA/dB- (B) (dA/dB-)2 (C) (dA/dB-)3 (D) (dA/dB-)4

Last Answer : (C) (dA/dB-)3

The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Description : The most important function of a washer is to provide bearing area and washers are normally specified by their hole diameters. The diameter of washer as compared to the nut is (A) More (B) Less (C) Same (D) More but less than the diameter of bolt

Last Answer : (A) More

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

What do you call a circuit that controls the magnetron output?A. Inverter B. Impeller C. Modulator D. Converter

Description : What do you call a circuit that controls the magnetron output? A. Inverter B. Impeller C. Modulator D. Converter

Last Answer : C. Modulator

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Last Answer : (C) Avoid chances of separation inside the impeller

Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Description : Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Last Answer : (B) Type of casing

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these

Last Answer : (B) Loss of kinetic head

In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Description : In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller

Last Answer : A) Mechanical

Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid from the periphery of the impeller and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Description : Which of the following is not the function of a volute casing provided in a centrifugal pump? (A) To reduce the head loss in discharge (B) To increase the pump efficiency (C) To collect liquid ... and to transmit it to the delivery pipe at constant velocity (D) To increase the pump discharge rate

Last Answer : Option D

How can you determine the largest impeller that a pump can handle?

Description : How can you determine the largest impeller that a pump can handle?

Last Answer : The motor amperage should be measured in the field with the pump discharge valve wide open. Subtract about 10% from the pumps maximum rated amperage. Then the maximum impeller size can be ... minus 10% A1 = Current operating amperage d2 = Maximum impeller diameter d1 = Current impeller diameter

Assume that water vaporizes at an absolute pressure of 1.5 m, barometric pressure head is 9.5 m and cavitation coefficient is 0.1 A turbine operates under a head of 40 m. the safe height of the runner above the tail water level, in meters, is : a) 6 b) 4 c) 3 d) 2

Description : Assume that water vaporizes at an absolute pressure of 1.5 m, barometric pressure head is 9.5 m and cavitation coefficient is 0.1 A turbine operates under a head of 40 m. the safe height of the runner above the tail water level, in meters, is : a) 6 b) 4 c) 3 d) 2

Last Answer : b) 4

For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing guide vane angle at inlet as 90o c) Providing runner vane angle at exit as 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Description : For attaining maximum efficiency, a Francis turbine runner is so designed as to result in radial discharge at exit. This is done by : a) Providing runner vane angle at inlet as 90o b) Providing ... 90o d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Last Answer : d) Designing for absolute velocity at outlet to be inclined at 90o to direction of vane there

Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters

Last Answer : Answer: Option A

The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Description : The ratio of strength of a hollow shaft to that of a solid shaft subjected to torsion if both are of the same material and of the same outer diameters, the inner diameter of hollow shaft being half of the outer diameter is a. 15/16 b. 16/15 c. 7/8 d. 8/7

Last Answer : a. 15/16

In parallel hybrid vehicle Internal Combustion Engine and electric motor are coupled by a …………………..device. a. Hydraulic b. Pneumatic c. Mechanical d. Electric

Description : In parallel hybrid vehicle Internal Combustion Engine and electric motor are coupled by a …………………..device. a. Hydraulic b. Pneumatic c. Mechanical d. Electric

Last Answer : c. Mechanical

At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 /μ: Reynold's number N is the impeller rotational speed, and D is the impeller diameter. (A) Po ∝ Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5

Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Description : Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Last Answer : (D) None of these

If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind its normal position as it rotates. This co A. hunting B. direct coupling C. peaking D. harmonic coupling

Description : If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind ... as it rotates. This co A. hunting B. direct coupling C. peaking D. harmonic coupling

Last Answer : Answer: A

If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ahead or behind its normal position as it rotates. This hu A. amortisseur windings B. direct coupling C. increase governor speed droop D. decreasing governor speed droop

Description : If the driving torque, such as that produced by a diesel engine, creates pulsations when coupled with a synchronous generator operating in parallel; the generator rotor may be periodically pulled ... windings B. direct coupling C. increase governor speed droop D. decreasing governor speed droop

Last Answer : Answer: A

The diameter of earth is 12,757 kilometers the diameter of satum is 120,664 the diameters of uranus is 51,499 is the sum of these three plantes diameters more or less than jupiter diameter of 142,804 kilometers by how much answer?

Description : The diameter of earth is 12,757 kilometers the diameter of satum is 120,664 the diameters of uranus is 51,499 is the sum of these three plantes diameters more or less than jupiter diameter of 142,804 kilometers by how much answer?

Last Answer : 2

The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Description : The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or (A) 12 bar diameters (B) 18 bar diameters (C) 24 bar diameters (D) 30 bar diameters

Last Answer : Answer: Option C

The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters

Last Answer : Answer: Option C

Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Description : Pick up the correct statement from the following: (A) All pipes and fittings are classified according to their diameters (B) The diameter of the pipes is the nominal diameter of internal bore (C) All pipes are measured along the centre line of the pipes in metres (D) All the above

Last Answer : (D) All the above

A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to

Description : A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to produce power at 50 Hz, the number of poles required in the generator are (A) 6 (B) 12 (C) 16 (D) 24

Last Answer : A hydraulic turbine having rated speed of 250 rpm is connected to a synchronous generator. In order to produce power at 50 Hz, the number of poles required in the generator are 24

For harnessing low variable water heads, the suitable hydraulic turbine with high percentage of reaction and

Description : For harnessing low variable water heads, the suitable hydraulic turbine with high percentage of reaction and runner adjustable vanes is  (A) Kaplan (B) Francis (C) Pelton (D) Impeller

Last Answer : For harnessing low variable water heads, the suitable hydraulic turbine with high percentage of reaction and runner adjustable vanes is Kaplan 

The success of oral rehydration therapy of diarrhoea depends upon the following process in the intestinal mucosa: A. Sodium pump mediated Na+ absorption B. Glucose coupled Na+ absorption C. Bicarbonate coupled Na+ absorption D. Passive Na+ diffusion secondary to nutrient absorption

Description : The success of oral rehydration therapy of diarrhoea depends upon the following process in the intestinal mucosa: A. Sodium pump mediated Na+ absorption B. Glucose coupled Na+ absorption C. Bicarbonate coupled Na+ absorption D. Passive Na+ diffusion secondary to nutrient absorption

Last Answer : B. Glucose coupled Na+ absorption

Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these

Last Answer : (A) Turbine

In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan

Description : In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan

Last Answer : (B) Turbine

Hydraulic intensifier is used for increasing the (A) Rate of velocity of liquid supply (B) Rate of flow through delivery pipeline of a pump (C) Intensity of pressure of the liquid (D) Momentum rate through delivery pipe

Description : Hydraulic intensifier is used for increasing the (A) Rate of velocity of liquid supply (B) Rate of flow through delivery pipeline of a pump (C) Intensity of pressure of the liquid (D) Momentum rate through delivery pipe

Last Answer : (C) Intensity of pressure of the liquid