Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation temperature of the liquid (C) Heat transfer from the surface of the liquid is less than that in film boiling (D) The temperature is less than that of film boiling

Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface
(B) Surface temperature is greater than the saturation temperature of the liquid
(C) Heat transfer from the surface of the liquid is less than that in film boiling
(D) The temperature is less than that of film boiling
by

1 Answer

Answer :

(D) The temperature is less than that of film boiling
by

Related questions

Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than that of the damp material (C) Ratio of its capacity to economy equals the steam consumption in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Description : Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than ... in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Last Answer : (B) Thermal conductivity of a dry material is more than that of the damp material

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

In case of __________ boiling, the liquid temperature is below the saturation temperature and the boiling takes place in the vicinity of the heated surface. (A) Nucleate (B) Local (C) Pool (D) Saturated

Description : In case of __________ boiling, the liquid temperature is below the saturation temperature and the boiling takes place in the vicinity of the heated surface. (A) Nucleate (B) Local (C) Pool (D) Saturated

Last Answer : (B) Local

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Description : The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Last Answer : (B) Vapour density

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Description : Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Last Answer : Option A

When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Description : When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Last Answer : (B) Nucleate boiling

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of a system decreases with the evolution of heat (C) Change of internal energy is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Description : Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of ... is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Last Answer : (D) The eccentric factor for all materials is always more than one

Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The boiling point of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Description : Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The ... of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Last Answer : (B) Filmwise condensation takes place on non-wettable surfaces

When vaporisation takes place through a blanketting film of gas, the phenomenon is termed as __________ boiling. (A) Pool (B) Nucleate (C) Transition (D) Film

Description : When vaporisation takes place through a blanketting film of gas, the phenomenon is termed as __________ boiling. (A) Pool (B) Nucleate (C) Transition (D) Film

Last Answer : (D) Film

Steady state temperature reached by a small amount of liquid evaporating into a large amount of unsaturated vapour-gas mixture is called the __________ temperature. (A) Dry-bulb (B) Wet-bulb (C) Dew point (D) Adiabatic saturation

Description : Steady state temperature reached by a small amount of liquid evaporating into a large amount of unsaturated vapour-gas mixture is called the __________ temperature. (A) Dry-bulb (B) Wet-bulb (C) Dew point (D) Adiabatic saturation

Last Answer : (B) Wet-bulb

In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Description : In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Last Answer : (B) Pool

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) Bubbles from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Description : In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) ... from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Last Answer : (B) Temperature of the heating surface is more than the boiling point of the liquid

Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Description : Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Last Answer : (A) Film

Relative humidity is the ratio of the (A) Partial pressure of the vapour to the vapour pressure of the liquid at room temperature (B) Partial pressure of the vapour to the vapour pressure of the liquid at gas temperature (C) Actual humidity to saturation humidity (D) None of these

Description : Relative humidity is the ratio of the (A) Partial pressure of the vapour to the vapour pressure of the liquid at room temperature (B) Partial pressure of the vapour to the vapour pressure of the liquid at gas temperature (C) Actual humidity to saturation humidity (D) None of these

Last Answer : (B) Partial pressure of the vapour to the vapour pressure of the liquid at gas temperatur

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

Pick up the correct statement from the following: (A) Absolute humidity at a given temperature is equal to weight of moisture present in a unit volume (B) Relative humidity is the ratio of actual vapour pressure and saturation vapour pressure at the same temperature (C) Relative humidity is the ratio of the weight of the vapours present per unit volume to the weight of vapours which could be contained at the same temperature when fully saturated (D) All the above

Description : Pick up the correct statement from the following: (A) Absolute humidity at a given temperature is equal to weight of moisture present in a unit volume (B) Relative humidity is the ratio of ... of vapours which could be contained at the same temperature when fully saturated (D) All the above

Last Answer : Answer: Option D

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Pick out the correct statement. (A) If an insoluble gas is passed through a volatile liquid placed in a perfectly insulated container, the temperature of the liquid will increase (B) A process is irreversible as long as Δ S for the system is greater than zero (C) The mechanical work done by a system is always equal to∫P.dV (D) The heat of formation of a compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Description : Pick out the correct statement. (A) If an insoluble gas is passed through a volatile liquid placed in a perfectly insulated container, the temperature of the liquid will increase (B) A ... compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Last Answer : (D) The heat of formation of a compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Pick out the wrong statement (A) Phase rule variables are intensive properties (B) Heat and work are both state function (C) The work done by expansion of a gas in vacuum is zero (D) CPand CVare state function

Description : Pick out the wrong statement (A) Phase rule variables are intensive properties (B) Heat and work are both state function (C) The work done by expansion of a gas in vacuum is zero (D) CPand CVare state function

Last Answer : (B) Heat and work are both state function

Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature (C) Double pipe heat exchangers are mostly used in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Description : Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat ... in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Last Answer : (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature

Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Description : Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Last Answer : (B) Sharp melting points

Pick out the wrong statement (A) A horizontal line on the humidity chart indicates the temperature changes at constant molal humidity (B) When water is cooled from 80 to 70°C by exposure to the air with a wet bulb temperature of 60°C, then both the approach & the range would be 10°C (C) For unsaturated air-water vapor mixture at atmospheric conditions, the wet bulb temperature & adiabatic cooling lines are the same (D) Relative saturation of unsaturated mixture of water vapor & air cannot be increased by either reducing the mixture temperature or by increasing the total pressure

Description : Pick out the wrong statement (A) A horizontal line on the humidity chart indicates the temperature changes at constant molal humidity (B) When water is cooled from 80 to 70°C by exposure ... & air cannot be increased by either reducing the mixture temperature or by increasing the total pressure

Last Answer : (D) Relative saturation of unsaturated mixture of water vapor & air cannot be increased by either reducing the mixture temperature or by increasing the total pressure

Film boiling is usually not desired in commercial equipments, because (A) The heat transfer rate is low in view of the large temperature drop (B) It is difficult to maintain (C) It is not economic (D) None of these

Description : Film boiling is usually not desired in commercial equipments, because (A) The heat transfer rate is low in view of the large temperature drop (B) It is difficult to maintain (C) It is not economic (D) None of these

Last Answer : (A) The heat transfer rate is low in view of the large temperature drop

Clapeyron equation is applicable for registration at (a) saturation point of vapour (b) saturation point of liquid (c) sublimation temperature (d) triple point.

Description : Clapeyron equation is applicable for registration at (a) saturation point of vapour (b) saturation point of liquid (c) sublimation temperature (d) triple point.

Last Answer : Ans: a

Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Last Answer : (D) Boiling of a liquid on a hot surface

The relative saturation of a partially saturated mixture of vapour and gas can be increased by __________ of the mixture. (A) Reducing the total pressure (B) Increasing the total pressure (C) Reducing the temperature (D) Both (B) and (C)

Description : The relative saturation of a partially saturated mixture of vapour and gas can be increased by __________ of the mixture. (A) Reducing the total pressure (B) Increasing the total pressure (C) Reducing the temperature (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Description : Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Last Answer : (A) Mass transfer co-efficient does not account for gas-liquid diffusion

Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Last Answer : (A) Less than the vapour pressure of the liquid at that temperature

Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in the tubes of natural circulation evaporators is in the range of 0.3 to 0.9 metre/second (C) Duhring's plot is used for calculating the concentration of solution (D) In a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Description : Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in ... a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Last Answer : (C) Duhring's plot is used for calculating the concentration of solution

Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year showing the cost at that time relative to a certain base year (C) Turnover ratio of a chemical plant is the ratio of gross annual sales to the fixed capital investment (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Description : Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year ... butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Last Answer : (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

__________________ is a liquid at the saturations which has temperature equal to the boiling point corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : __________________ is a liquid at the saturations which has temperature equal to the boiling point corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Saturated Liquid

Nucleate boiling is promoted (A) On polished surfaces (B) On rough surfaces (C) In the absence of agitation (D) None of these

Description : Nucleate boiling is promoted (A) On polished surfaces (B) On rough surfaces (C) In the absence of agitation (D) None of these

Last Answer : (B) On rough surfaces

Pick out the wrong statement. (A) The Reynolds analogy for mass transfer is given by Lewis relation and is applicable, when Schmidt number is one (B) Sherwood number for flow in pipes can be expressed as the ratio of the concentration gradient at wall to the overall concentration difference (C) According to film theory for equimolar counter diffusion, the mass transfer coefficient is given by DAB(B)P - 3, Q - 2 (D) The z-component of the total mass flux of a component A in binary mixture of A and B is given by - Dab'.dCA/dz

Description : Pick out the wrong statement. (A) The Reynolds analogy for mass transfer is given by Lewis relation and is applicable, when Schmidt number is one (B) Sherwood number for flow in pipes can be expressed ... flux of a component A in binary mixture of A and B is given by - Dab'.dCA/dz

Last Answer : (C) According to film theory for equimolar counter diffusion, the mass transfer coefficient is given by DAB(B)P - 3, Q - 2

The pressure outside a bubble/droplet of liquid is __________ the internal pressure. (A) Greater than (B) Less than (C) Equal to (D) Unpredictable; depends on the bubble size

Description : The pressure outside a bubble/droplet of liquid is __________ the internal pressure. (A) Greater than (B) Less than (C) Equal to (D) Unpredictable; depends on the bubble size

Last Answer : Option B

Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to Nusselt number in heat transfer and Schmidt number to Prandtl number (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger (D) Hot gases at moderate pressure are usually in the shell side of shell and tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Description : Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to ... tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Last Answer : (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger

Pick out the correct statement. (A) For identical gas flow rates, less pressure drop occurs through a plate tower than through a packed tower (B) Plate column can handle greater liquid loads without flooding than packed column, but the liquid hold up is more in the case of plate column (C) For the same duty, plate columns weigh less than packed columns (D) All (A), (B) and (C)

Description : Pick out the correct statement. (A) For identical gas flow rates, less pressure drop occurs through a plate tower than through a packed tower (B) Plate column can handle greater liquid loads without flooding than packed ... duty, plate columns weigh less than packed columns (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement: (A) Absorption factor is constant, when the equilibrium and operating lines are straight (B) In case of a stripper, the equilibrium curve is always below the operating line (C) In case of an absorber, the operating line is always above the equilibrium curve (D) In the absorption of low solubility gases, the liquid film is the controlling resistance

Description : Pick out the wrong statement: (A) Absorption factor is constant, when the equilibrium and operating lines are straight (B) In case of a stripper, the equilibrium curve is always below ... (D) In the absorption of low solubility gases, the liquid film is the controlling resistance

Last Answer : (B) In case of a stripper, the equilibrium curve is always below the operating line

Pick out the wrong statement. (A) Swenson-Walker crystalliser is a batch crystalliser (B) Super saturation of the solution is the driving potential for a crystal growth (C) The liquor left after the removal of crystals from a solution is called mother liquor (D) The first stage of crystal formation is called nucleation

Description : Pick out the wrong statement. (A) Swenson-Walker crystalliser is a batch crystalliser (B) Super saturation of the solution is the driving potential for a crystal growth (C) The ... a solution is called mother liquor (D) The first stage of crystal formation is called nucleation

Last Answer : (A) Swenson-Walker crystalliser is a batch crystalliser

Pick out the wrong statement: (A) The expansion of a gas in vacuum is an irreversible process (B) An isometric process is a constant pressure process (C) Entropy change for a reversible adiabatic process is zero (D) Free energy change for a spontaneous process is negative

Description : Pick out the wrong statement: (A) The expansion of a gas in vacuum is an irreversible process (B) An isometric process is a constant pressure process (C) Entropy change for a reversible adiabatic process is zero (D) Free energy change for a spontaneous process is negative

Last Answer : (B) An isometric process is a constant pressure process