The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

The burnout heat flux in the nucleate boiling regime is not a function of the
(A) Liquid density
(B) Vapour density
(C) Temperature difference
(D) Heat of evaporation
by

1 Answer

Answer :

(B) Vapour density
by

Related questions

Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation temperature of the liquid (C) Heat transfer from the surface of the liquid is less than that in film boiling (D) The temperature is less than that of film boiling

Description : Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation ... less than that in film boiling (D) The temperature is less than that of film boiling

Last Answer : (D) The temperature is less than that of film boiling

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

In a boiling curve, the peak heat flux is called the __________ point. (A) Nusselt (B) Leidenfrost (C) Boiling (D) Burnout

Description : In a boiling curve, the peak heat flux is called the __________ point. (A) Nusselt (B) Leidenfrost (C) Boiling (D) Burnout

Last Answer : (D) Burnout

In the free convection regime of pool boiling, the heat flux is proportional to (A) Δt 1/2 (B) Δt 2 (C) Δt 5/4 (D) Δt

Description : In the free convection regime of pool boiling, the heat flux is proportional to (A) Δt 1/2 (B) Δt 2 (C) Δt 5/4 (D) Δt

Last Answer : (C) Δt 5/4

When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Description : When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Last Answer : (B) Nucleate boiling

In case of __________ boiling, the liquid temperature is below the saturation temperature and the boiling takes place in the vicinity of the heated surface. (A) Nucleate (B) Local (C) Pool (D) Saturated

Description : In case of __________ boiling, the liquid temperature is below the saturation temperature and the boiling takes place in the vicinity of the heated surface. (A) Nucleate (B) Local (C) Pool (D) Saturated

Last Answer : (B) Local

In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Description : In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Last Answer : (B) Pool

Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than that of the damp material (C) Ratio of its capacity to economy equals the steam consumption in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Description : Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than ... in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Last Answer : (B) Thermal conductivity of a dry material is more than that of the damp material

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Description : Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Last Answer : Option A

Heat flux increases with temperature drop beyond the Leiden frost point in the plot of heat flux vs. temperature drop for a boiling liquid, because (A) Convection becomes important (B) Conduction becomes important (C) Radiation becomes important (D) Sub-cooled boiling occurs

Description : Heat flux increases with temperature drop beyond the Leiden frost point in the plot of heat flux vs. temperature drop for a boiling liquid, because (A) Convection becomes important (B) Conduction becomes important (C) Radiation becomes important (D) Sub-cooled boiling occurs

Last Answer : (C) Radiation becomes important

Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward feeding in multiple effect evaporation (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Description : Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward ... (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Last Answer : (A) Get economical temperature difference by using moderate pressure steam

Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Last Answer : (D) Boiling of a liquid on a hot surface

Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Description : Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Last Answer : (A) Film

When vaporisation takes place through a blanketting film of gas, the phenomenon is termed as __________ boiling. (A) Pool (B) Nucleate (C) Transition (D) Film

Description : When vaporisation takes place through a blanketting film of gas, the phenomenon is termed as __________ boiling. (A) Pool (B) Nucleate (C) Transition (D) Film

Last Answer : (D) Film

Nucleate boiling is promoted (A) On polished surfaces (B) On rough surfaces (C) In the absence of agitation (D) None of these

Description : Nucleate boiling is promoted (A) On polished surfaces (B) On rough surfaces (C) In the absence of agitation (D) None of these

Last Answer : (B) On rough surfaces

In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) Bubbles from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Description : In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) ... from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Last Answer : (B) Temperature of the heating surface is more than the boiling point of the liquid

The amount of heat required to change a boiling liquid to a gas at the same temperature depends on one of the following properties of the liquid. Does it depend on the liquid's: w) heat of fusion x) heat of vaporization y) temperature z) density

Description : The amount of heat required to change a boiling liquid to a gas at the same temperature depends on one of the following properties of the liquid. Does it depend on the liquid's: w) heat of fusion x) heat of vaporization y) temperature z) density

Last Answer : ANSWER: X -- HEAT OF VAPORIZATION

The use of pressurized radiator cap is to a) Reduce evaporation loss b) Increase engine operating temperature c) Increase boiling point of water d) Reduce heat losses

Description : The use of pressurized radiator cap is to a) Reduce evaporation loss b) Increase engine operating temperature c) Increase boiling point of water d) Reduce heat losses

Last Answer : ans c

Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in the tubes of natural circulation evaporators is in the range of 0.3 to 0.9 metre/second (C) Duhring's plot is used for calculating the concentration of solution (D) In a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Description : Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in ... a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Last Answer : (C) Duhring's plot is used for calculating the concentration of solution

The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Description : The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Last Answer : Ans: b

For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should be used (c) perfectly tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Description : For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should ... tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Last Answer : Ans: c

The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Description : The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Last Answer : (A) Increase

Use of water as a manometric liquid suffers from the disadvantage of its (A) Low vapour pressure (B) Corrosive nature (C) High vapour pressure (D) High boiling point

Description : Use of water as a manometric liquid suffers from the disadvantage of its (A) Low vapour pressure (B) Corrosive nature (C) High vapour pressure (D) High boiling point

Last Answer : (C) High vapour pressure

Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of vaporisation is constant (C) Volume in the liquid state is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Description : Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of ... is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Description : An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Last Answer : (C) Both (A) and (B)

To obtain integrated form of Clausius-Clapeyron equation, ln (P2/P1) = (∆HV/R) (1/T1- 1/T2) from the exact Clapeyron equation, it is assumed that the (A) Volume of the liquid phase is negligible compared to that of vapour phase (B) Vapour phase behaves as an ideal gas (C) Heat of vaporisation is independent of temperature (D) All (A), (B) & (C)

Description : To obtain integrated form of Clausius-Clapeyron equation, ln (P2/P1) = (∆HV/R) (1/T1- 1/T2) from the exact Clapeyron equation, it is assumed that the (A) Volume of the liquid phase is negligible compared to ... gas (C) Heat of vaporisation is independent of temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Description : Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Last Answer : Ans: d

Water vapour turns into clouds in the atmosphere when: A. It rains B. The temperature rise C. Dew point is reached (Answer) D. Evaporation takes place

Description : Water vapour turns into clouds in the atmosphere when: A. It rains B. The temperature rise C. Dew point is reached (Answer) D. Evaporation takes place

Last Answer : C. Dew point is reached (Answer)

The non-dimensional temperature gradient in a liquid at the wall of a pipe is the (A) Heat flux (B) Nusselt number (C) Prandtl number (D) Schmidt number

Description : The non-dimensional temperature gradient in a liquid at the wall of a pipe is the (A) Heat flux (B) Nusselt number (C) Prandtl number (D) Schmidt number

Last Answer : (A) Heat flux

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only

An indication of sensible heat content in air-water vapour mixture is a) wet bulb temperature b) dew point temperature c) density of air d) dry bulb temperature

Description : An indication of sensible heat content in air-water vapour mixture is a) wet bulb temperature b) dew point temperature c) density of air d) dry bulb temperature

Last Answer : d) dry bulb temperature

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

In the pressure cooker, cooking is faster because the increase in vapour pressure - (1) increase the specific heat (2) decreases the specific heat (3) decreases the boiling point (4) increases the boiling point

Description : In the pressure cooker, cooking is faster because the increase in vapour pressure - (1) increase the specific heat (2) decreases the specific heat (3) decreases the boiling point (4) increases the boiling point

Last Answer : (4) increases the boiling point

At the critical point of a substance (A) The surface tension vanishes (B) Liquid and vapour have the same density (C) There is no distinction between liquid and vapour phases (D) All (A), (B) and (C)

Description : At the critical point of a substance (A) The surface tension vanishes (B) Liquid and vapour have the same density (C) There is no distinction between liquid and vapour phases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Heat sensitive materials with very high latent heat of vaporisation may be economically separated using (A) Liquid extraction (B) Distillation (C) Evaporation (D) Absorption

Description : Heat sensitive materials with very high latent heat of vaporisation may be economically separated using (A) Liquid extraction (B) Distillation (C) Evaporation (D) Absorption

Last Answer : (A) Liquid extraction

In case of evaporators, liquid entrainment results primarily due to (A) High vacuum in the evaporator (B) High evaporation rate (C) Foaming of the solution (D) High heat transfer rate

Description : In case of evaporators, liquid entrainment results primarily due to (A) High vacuum in the evaporator (B) High evaporation rate (C) Foaming of the solution (D) High heat transfer rate

Last Answer : (C) Foaming of the solution

The actual temperature drop across the heating surface in an evaporator depends on the (A) Feed (B) Depth of liquid over heating surface (C) Pressure difference between steam chest and vapour space (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface in an evaporator depends on the (A) Feed (B) Depth of liquid over heating surface (C) Pressure difference between steam chest and vapour space (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

At a fixed total pressure, humidity depends only on the (A) Partial pressure of vapour in the mixture (B) Heat capacity of the vapour (C) Density of the vapour (D) None of these

Description : At a fixed total pressure, humidity depends only on the (A) Partial pressure of vapour in the mixture (B) Heat capacity of the vapour (C) Density of the vapour (D) None of these

Last Answer : (A) Partial pressure of vapour in the mixture

At boiling point of liquids, its : (1) Temperature increases (2) Atmospheric pressure increases (3) Timperature remains increases (4) Vapour pressure decreases

Description : At boiling point of liquids, its : (1) Temperature increases (2) Atmospheric pressure increases (3) Timperature remains increases (4) Vapour pressure decreases

Last Answer : (3) Timperature remains increases

At boiling point of liquids, its – (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Description : At boiling point of liquids, its – (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Last Answer : (3) Temperature remains constant Explanation: An interesting property of matter is that its temperature remains constant during a phase change, assuming its surrounding pressure is constant. A liquid changes into gaseous state at a constant temperature called its boiling point.

At boiling point of liquids, its (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Description : At boiling point of liquids, its (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases 

Last Answer : Temperature remains constant

Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of a system decreases with the evolution of heat (C) Change of internal energy is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Description : Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of ... is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Last Answer : (D) The eccentric factor for all materials is always more than one

If the vapour pressure at two temperatures of a solid phase in equilibrium with its liquid phase are known, then the latent heat of fusion can be calculated by the (A) Maxwell's equation (B) Clausius-Clapeyron Equation (C) Van Laar equation (D) Nernst Heat Theorem

Description : If the vapour pressure at two temperatures of a solid phase in equilibrium with its liquid phase are known, then the latent heat of fusion can be calculated by the (A) Maxwell's equation (B) Clausius-Clapeyron Equation (C) Van Laar equation (D) Nernst Heat Theorem

Last Answer : B) Clausius-Clapeyron Equation

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

Whats the difference between burnout paradise and Burnout: Paradise - The Ultimate Box?

Description : Whats the difference between burnout paradise and Burnout: Paradise - The Ultimate Box?

Last Answer : The wonderful thing about Google, is Google's a wonderful thing. I used my eyes and I read on those pages, mostly Wikipedia. It seems that the box comes with more cars, more tracks, offline ... the expansion packs, etc. Likely everything that comes with the game, with the ultimate name and whatnot.

The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Nusselt number is the ratio of the temperature gradient at the wall to (A) Temperature difference (B) Heat flux (C) That across the entire pipe (D) None of these

Description : Nusselt number is the ratio of the temperature gradient at the wall to (A) Temperature difference (B) Heat flux (C) That across the entire pipe (D) None of these

Last Answer : (C) That across the entire pipe

Nusselt number is the ratio of the (A) Temperature gradient of the wall to that across the entire pipe (B) Temperature difference to the temperature gradient at the wall (C) Heat flux at the wall to that across the entire pipe (D) None of these

Description : Nusselt number is the ratio of the (A) Temperature gradient of the wall to that across the entire pipe (B) Temperature difference to the temperature gradient at the wall (C) Heat flux at the wall to that across the entire pipe (D) None of these

Last Answer : (C) Heat flux at the wall to that across the entire pipe