Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The boiling point of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Pick out the wrong statement.
(A) Heat transfer from a hot body to cold body by the emission of heat
waves is called radiation
(B) Filmwise condensation takes place on non-wettable surfaces
(C) The boiling point of a solution is affected by liquid head as well as
boiling point elevation
(D) None of these
by

1 Answer

Answer :

(B) Filmwise condensation takes place on non-wettable surfaces
by

Related questions

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Last Answer : (D) Boiling of a liquid on a hot surface

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

For condensation of pure vapors, if the heat transfer co-efficients in filmwise and drop-wise condensation are respectively hf and hd , then (A) hf = hd (B) hf > hd (C) hf < hd (D) hf could be greater or smaller than hd

Description :  For condensation of pure vapors, if the heat transfer co-efficients in filmwise and drop-wise condensation are respectively hf and hd , then (A) hf = hd (B) hf > hd (C) hf < hd (D) hf could be greater or smaller than hd

Last Answer : (C) hf < hd

Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is proportional to the number of times the fluid crosses the bundle between baffles (C) Propagation velocity for travel of heat radiation through vacuum is equal to the velocity of the light (D) The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Description : Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is ... The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Last Answer : (A) Heat transfer by radiation cannot occur across an absolute volume

Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in the tubes of natural circulation evaporators is in the range of 0.3 to 0.9 metre/second (C) Duhring's plot is used for calculating the concentration of solution (D) In a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Description : Pick out the wrong statement. (A) The value of hydrostatic head increases with increase in vacuum in the effect in a multiple effect evaporator system (B) Entering velocity of the liquid in ... a multiple effect evaporation system, the number of effects is limited by the total boiling point rise

Last Answer : (C) Duhring's plot is used for calculating the concentration of solution

Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature (C) Double pipe heat exchangers are mostly used in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Description : Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat ... in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Last Answer : (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature

The thickness of condensate layer in filmwise condensation depends on the (A) Condensation rate (B) Surface configuration (C) Liquid flow rate from the surface (D) All (A), (B) and (C)

Description : The thickness of condensate layer in filmwise condensation depends on the (A) Condensation rate (B) Surface configuration (C) Liquid flow rate from the surface (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

. A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of all the effects is -less than that in a single effect evaporator system (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect (C) Boiling point elevation in a single effect system is much higher than that in any effect in a multi-effect system (D) Heat transfer co-efficient in a single effect is much lower than that in any effect in a multi-effect system

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation temperature of the liquid (C) Heat transfer from the surface of the liquid is less than that in film boiling (D) The temperature is less than that of film boiling

Description : Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation ... less than that in film boiling (D) The temperature is less than that of film boiling

Last Answer : (D) The temperature is less than that of film boiling

Pick out the wrong statement. (A) Biological oxygen demand (B.O.D.) value of a sewerage sample is always lower than its chemical oxygen demand (C.O.D.) value (B) Environmental pollution by NOx emission is much higher by four stroke petrol engines as compared to the two stroke engines (C) Temperature in stratosphere rises with increasing altitude (D) The characteristic of a green house body is that it allows the long wavelength incoming solar radiation to come in but does not allow the short wavelength infra red radiation to escape out of the earth's atmosphere

Description : Pick out the wrong statement. (A) Biological oxygen demand (B.O.D.) value of a sewerage sample is always lower than its chemical oxygen demand (C.O.D.) value (B) Environmental pollution by ... in but does not allow the short wavelength infra red radiation to escape out of the earth's atmosphere

Last Answer : (D) The characteristic of a green house body is that it allows the long wavelength incoming solar radiation to come in but does not allow the short wavelength infra red radiation to escape out of the earth's atmosphere

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

Pick out the wrong statement. (A) Fluid movement under the influence of buoyant forces resulting from change in density takes place in case of natural convection (B) The ratio NNu /NRe . Npr is called the Stanton number (C) The Peclet number is a measure of the ratio of energy transport by convection to that by conduction (D) The Colburn jH factor for heat transfer is given by Nst Npr

Description : Pick out the wrong statement. (A) Fluid movement under the influence of buoyant forces resulting from change in density takes place in case of natural convection (B) The ratio NNu /NRe . Npr is ... convection to that by conduction (D) The Colburn jH factor for heat transfer is given by Nst Npr

Last Answer : (D) The Colburn jH factor for heat transfer is given by Nst Npr

Pick out the wrong statement. (A) In a static mass of liquid, the pressure at a point is the same for all liquids (B) Pressure decreases exponentially with elevation in an isothermal atmosphere(C) Atmospheric pressure = absolute pressure ‒ gage pressure(D) As per Pascal's law, the pressure at a point in a static or uniformlymoving fluid is equal in all directions

Description : Pick out the wrong statement. (A) In a static mass of liquid, the pressure at a point is the same for all liquids (B) Pressure decreases exponentially with elevation in an isothermal atmosphere (C) ... s law, the pressure at a point in a static or uniformly moving fluid is equal in all directions

Last Answer : (A) In a static mass of liquid, the pressure at a point is the same for all liquids

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

Pick out the wrong statement. Raoult's law does not apply, when the (A) Size of component molecules are not equal (B) Attractive forces between like and unlike molecules in the solution are approximately equal (C) Component molecules are non-polar (D) Chemical combination or molecular association between unlike molecules takes place in the formation of solution

Description : Pick out the wrong statement. Raoult's law does not apply, when the (A) Size of component molecules are not equal (B) Attractive forces between like and unlike molecules ... D) Chemical combination or molecular association between unlike molecules takes place in the formation of solution

Last Answer : (C) Component molecules are non-polar

What is the amount of heat needed to turn 1kg of the substance at its boiling point from the liquid to the gaseous state?  A. Heat of fusion  B. Heat of vaporation  C. Heat of condensation  D. Heat of fission

Description : What is the amount of heat needed to turn 1kg of the substance at its boiling point from the liquid to the gaseous state?  A. Heat of fusion  B. Heat of vaporation  C. Heat of condensation  D. Heat of fission

Last Answer : Heat of vaporation

Pick out the wrong statement pertaining to the soap manufacture. (A) Transparent soaps are made by cold process (B) Organic pigments are used as colouring materials in the soap manufacture (C) Both laundry as well as toilet soaps are manufactured by hot process (D) Colourless rosin is used in the manufacture of laundry soaps

Description : Pick out the wrong statement pertaining to the soap manufacture. (A) Transparent soaps are made by cold process (B) Organic pigments are used as colouring materials in the soap manufacture (C) ... soaps are manufactured by hot process (D) Colourless rosin is used in the manufacture of laundry soaps

Last Answer : (A) Transparent soaps are made by cold process

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to Nusselt number in heat transfer and Schmidt number to Prandtl number (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger (D) Hot gases at moderate pressure are usually in the shell side of shell and tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Description : Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to ... tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Last Answer : (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Gibbs phase rule finds application, when heat transfer occurs by (A) Conduction (B) Convection (C) Radiation (D) Condensation

Description : Gibbs phase rule finds application, when heat transfer occurs by (A) Conduction (B) Convection (C) Radiation (D) Condensation

Last Answer : (D) Condensation

Heat flux increases with temperature drop beyond the Leiden frost point in the plot of heat flux vs. temperature drop for a boiling liquid, because (A) Convection becomes important (B) Conduction becomes important (C) Radiation becomes important (D) Sub-cooled boiling occurs

Description : Heat flux increases with temperature drop beyond the Leiden frost point in the plot of heat flux vs. temperature drop for a boiling liquid, because (A) Convection becomes important (B) Conduction becomes important (C) Radiation becomes important (D) Sub-cooled boiling occurs

Last Answer : (C) Radiation becomes important

What type of heat transfer is affected by the colour of surfaces?

Description : What type of heat transfer is affected by the colour of surfaces?

Last Answer : Need answer

Boiling point elevation of a solution of NaOH (A) Increases rapidly with temperature rise (B) Is almost independent of temperature (C) Is almost independent of pressure (D) Both (B) and (C)

Description : Boiling point elevation of a solution of NaOH (A) Increases rapidly with temperature rise (B) Is almost independent of temperature (C) Is almost independent of pressure (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Boiling point elevation of an ideal solution (A) Increases rapidly with temperature rise (B) Decreases rapidly with temperature rise (C) In independent of pressure (D) Both (B) and (C)

Description : Boiling point elevation of an ideal solution (A) Increases rapidly with temperature rise (B) Decreases rapidly with temperature rise (C) In independent of pressure (D) Both (B) and (C)

Last Answer : (A) Increases rapidly with temperature rise

. Boiling point elevation for a strong and concentrated solution is found by Duhring's rule, which states that at the same pressure, the boiling point of a solution is a linear function of the __________ of pure water. (A) Boiling point (B) Dynamic viscosity (C) Kinematic viscosity (D) Density

Description : . Boiling point elevation for a strong and concentrated solution is found by Duhring's rule, which states that at the same pressure, the boiling point of a solution is a linear function of the __________ of pure water. (A) Boiling point (B) Dynamic viscosity (C) Kinematic viscosity (D) Density

Last Answer : (A) Boiling point

The capacity of double-effect evaporator is less than half of the capacity of two single effects, each of which is operating over same terminal temperature difference, when the (A) Solution has an elevation of boiling point (B) Evaporators operate under vacuum (C) Evaporators operate at atmospheric pressure (D) None of these

Description : The capacity of double-effect evaporator is less than half of the capacity of two single effects, each of which is operating over same terminal temperature difference, when the (A) Solution has ... B) Evaporators operate under vacuum (C) Evaporators operate at atmospheric pressure (D) None of these

Last Answer : (A) Solution has an elevation of boiling point

Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than that of the damp material (C) Ratio of its capacity to economy equals the steam consumption in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Description : Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than ... in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Last Answer : (B) Thermal conductivity of a dry material is more than that of the damp material

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by (A) Conduction (B) Convection (C) Radiation (D) Cannot be predicted

Description : In furnaces operating at very high temperature (say) 1250°C, e.g. soaking pit), the maximum heat transfer takes place by (A) Conduction (B) Convection (C) Radiation (D) Cannot be predicted

Last Answer : (C) Radiation

Pick out the wrong statement. (A) A particular chemical reaction is more temperature sensitive at low temperatures (B) A very high value of equilibrium constant, K (K >> 1) indicates that the reaction is practically irreversible in nature (C) The intercept of the Arrhenius plot is called the 'activation energy' (D) Non-ideal flow takes place in reactors due to recycling, channeling or by creation of stagnant regions

Description : Pick out the wrong statement. (A) A particular chemical reaction is more temperature sensitive at low temperatures (B) A very high value of equilibrium constant, K (K >> 1) indicates that the ... ) Non-ideal flow takes place in reactors due to recycling, channeling or by creation of stagnant regions

Last Answer : (C) The intercept of the Arrhenius plot is called the 'activation energy

Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of a system decreases with the evolution of heat (C) Change of internal energy is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Description : Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of ... is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Last Answer : (D) The eccentric factor for all materials is always more than one

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

Transfer of heat energy from a heater coil to the cooking vessel takes place through the process of- (1) Convection only (2) Conduction and convection only (3) Radiation and convection only (4) Convection, conduction and radiation

Description : Transfer of heat energy from a heater coil to the cooking vessel takes place through the process of- (1) Convection only (2) Conduction and convection only (3) Radiation and convection only (4) Convection, conduction and radiation

Last Answer : (3) Radiation and convection only Explanation: Conduction is the transfer of heat energy by direct contact, convection is the movement of heat by actual motion of matter; radiation is the transfer of energy with the help of electromagnetic waves.

Pick out the wrong statement. (A) Atoms with same number of nucleons but different number of protons are called isobars (B) Atoms with same number of protons but different number of nucleons are called isoters (C) Out of α, β, and γ-rays, the one having maximum penetration power are γ-rays (D) The product formed by emission of α-particle has mass number less by 4 units than the parent nuclide

Description : Pick out the wrong statement. (A) Atoms with same number of nucleons but different number of protons are called isobars (B) Atoms with same number of protons but different number of nucleons are ... product formed by emission of α-particle has mass number less by 4 units than the parent nuclide

Last Answer : (B) Atoms with same number of protons but different number of nucleons are called isoters

Pick out the wrong statement. (A) Cold SBR is superior as compared to hot SBR (B) Polymerisation temperature can modify the properties of SBR (C) Production of cold SBR employs lower pressure as compared to that of hot SBR (D) None of these

Description : Pick out the wrong statement. (A) Cold SBR is superior as compared to hot SBR (B) Polymerisation temperature can modify the properties of SBR (C) Production of cold SBR employs lower pressure as compared to that of hot SBR (D) None of these

Last Answer : (D) None of these

Pick out the wrong statement(A) Cold rubber (SBR) is superior as compared to hot rubber (SBR)(B) Polymerisation temperature can modify the properties of SBR(C) Production of cold SBR employs lower pressure as compared to that ofhot SBR(D) None of these

Description : Pick out the wrong statement (A) Cold rubber (SBR) is superior as compared to hot rubber (SBR) (B) Polymerisation temperature can modify the properties of SBR (C) Production of cold SBR employs lower pressure as compared to that of hot SBR (D) None of these

Last Answer : (D) None of these

Pick out the wrong statement. (A) DDT is manufactured by the condensation of chlorobenzene with chloral at 30°C in presence of oleum, which is a highly exothermic reaction (B) Chloral is obtained by the chlorination of ethyl alcohol (C) Insecticides acting on the insects through the respiratory system are called fumigants (D) Benzene hexachloride is not a contact insecticide

Description : Pick out the wrong statement. (A) DDT is manufactured by the condensation of chlorobenzene with chloral at 30°C in presence of oleum, which is a highly exothermic reaction (B) Chloral ... through the respiratory system are called fumigants (D) Benzene hexachloride is not a contact insecticide

Last Answer : (D) Benzene hexachloride is not a contact insecticide

Pick out the wrong statement. (A) α-particle emission from a radioactive element makes it electrically negative (B) β-particle emission from a radioactive element makes it electrically positive (C) A radioactive element having a half life period of 20 years will completely disintegrated in 40 years (D) The disintegration constant of a radioactive isotope is independent of pressure, temperature or concentration

Description : Pick out the wrong statement. (A) α-particle emission from a radioactive element makes it electrically negative (B) β-particle emission from a radioactive element makes it electrically ... ) The disintegration constant of a radioactive isotope is independent of pressure, temperature or concentration

Last Answer : (C) A radioactive element having a half life period of 20 years will completely disintegrated in 40 years

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Description : Pick out the wrong statement. (A) Mass transfer co-efficient does not account for gas-liquid diffusion (B) Diffusion co-efficient and mass transfer co-efficient are not same in any mass transfer operation

Last Answer : (A) Mass transfer co-efficient does not account for gas-liquid diffusion

Pick out the wrong statement. (A) Addition polymers are generally formed by chain growth polymerisation (B) Condensation polymers are generally formed by step growth polymerisation (C) Teflon is formed by step growth polymerisation (D) Bakelite is formed by step growth polymerisation

Description : Pick out the wrong statement. (A) Addition polymers are generally formed by chain growth polymerisation (B) Condensation polymers are generally formed by step growth polymerisation (C) Teflon is formed by step growth polymerisation (D) Bakelite is formed by step growth polymerisation

Last Answer : C) Teflon is formed by step growth polymerisation

Pick out the wrong statement. (A) 'Green acid' is the other name of phosphoric acid produced by the reaction of phosphate rock & sulphuric acid (B) Chemically unreactive nature of red phosphorous is due to its polymeric structure (C) Red phosphorous is the most reactive allotropic form of phosphorous (D) Red phosphorous, which is used in the manufacture of safety matches, is converted into white phosphorous by vaporisation followed by condensation

Description : Pick out the wrong statement. (A) 'Green acid' is the other name of phosphoric acid produced by the reaction of phosphate rock & sulphuric acid (B) Chemically unreactive nature of ... in the manufacture of safety matches, is converted into white phosphorous by vaporisation followed by condensation

Last Answer : (C) Red phosphorous is the most reactive allotropic form of phosphorous

Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace

Description : Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace

Last Answer : (C) Salt bath furnace

Pick out the wrong statement: (A) Reboiler is not used in open steam distillation (B) The separation of solutes of different molecular sizes in a liquid solution by use of a suitable membrane is called dialysis (C) Freeze drying is used for the drying of fish (D) Fenske-Underwood equation is used for calculating theoretical number of plates in a distillation column at normal operating reflux condition

Description : Pick out the wrong statement: (A) Reboiler is not used in open steam distillation (B) The separation of solutes of different molecular sizes in a liquid solution by use of a ... is used for calculating theoretical number of plates in a distillation column at normal operating reflux condition

Last Answer : (D) Fenske-Underwood equation is used for calculating theoretical number of plates in a distillation column at normal operating reflux condition