In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) Bubbles from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

In sub-cooled boiling,
(A) Temperature of the heating surface is less than the boiling point of the
liquid
(B) Temperature of the heating surface is more than the boiling point of the
liquid
(C) Bubbles from heating surface are absorbed by the mass of the liquid
(D) Very large vapour space is necessary
by

1 Answer

Answer :

(B) Temperature of the heating surface is more than the boiling point of the
liquid
by

Related questions

In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Description : In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Last Answer : (B) Pool

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

Heat flux increases with temperature drop beyond the Leiden frost point in the plot of heat flux vs. temperature drop for a boiling liquid, because (A) Convection becomes important (B) Conduction becomes important (C) Radiation becomes important (D) Sub-cooled boiling occurs

Description : Heat flux increases with temperature drop beyond the Leiden frost point in the plot of heat flux vs. temperature drop for a boiling liquid, because (A) Convection becomes important (B) Conduction becomes important (C) Radiation becomes important (D) Sub-cooled boiling occurs

Last Answer : (C) Radiation becomes important

A liquid under pressure greater than its vapour pressure for the temperature involved is called a __________ liquid. (A) Sub-cooled (B) Saturated (C) Non-solidifiable (D) None of these

Description : A liquid under pressure greater than its vapour pressure for the temperature involved is called a __________ liquid. (A) Sub-cooled (B) Saturated (C) Non-solidifiable (D) None of these

Last Answer : (A) Sub-cooled

__________________ is a liquid at the saturations which has temperature equal to the boiling point corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : __________________ is a liquid at the saturations which has temperature equal to the boiling point corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Saturated Liquid

The actual temperature drop across the heating surface in an evaporator depends on the (A) Feed (B) Depth of liquid over heating surface (C) Pressure difference between steam chest and vapour space (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface in an evaporator depends on the (A) Feed (B) Depth of liquid over heating surface (C) Pressure difference between steam chest and vapour space (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation temperature of the liquid (C) Heat transfer from the surface of the liquid is less than that in film boiling (D) The temperature is less than that of film boiling

Description : Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation ... less than that in film boiling (D) The temperature is less than that of film boiling

Last Answer : (D) The temperature is less than that of film boiling

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Description : The actual temperature drop across the heating surface of an evaporator depends on the (A) Liquid depth over the heating surface (B) Solution being evaporated (C) Pressure difference between the steam chest and the vapor space above the boiling liquid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Description : In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Last Answer : Ans: d

Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation (A) Pressure falls below the vapour pressure (B) Pressure becomes very high (C) Temperature becomes low (D) All 'a', 'b' & 'c'

Description : Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation (A) Pressure falls below the vapour pressure (B) Pressure becomes very high (C) Temperature becomes low (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Description : When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Last Answer : (B) Nucleate boiling

Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Description : Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Last Answer : (A) Film

The temperature to which a vapour gas mixture must be cooled (at varying humidity) to become saturated is called the __________ temperature. (A) Dew point (B) Wet bulb (C) Dry bulb (D) None of these

Description : The temperature to which a vapour gas mixture must be cooled (at varying humidity) to become saturated is called the __________ temperature. (A) Dew point (B) Wet bulb (C) Dry bulb (D) None of these

Last Answer : (D) None of these

_________________ is one which has a pressure higher than the saturation pressure corresponding to the existing temperature.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : _________________ is one which has a pressure higher than the saturation pressure corresponding to the existing temperature.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Compressed Liquid

________________ is one which has a temperature lower than the saturation temperature corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : ________________ is one which has a temperature lower than the saturation temperature corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Sub cooled Liquid

Most of the nuclear power plants operating in the United States are: w) pressurized water reactors x) boiling water reactors y) high-temperature gas-cooled reactors z) liquid-metal fast breeder reactors

Description : Most of the nuclear power plants operating in the United States are: w) pressurized water reactors x) boiling water reactors y) high-temperature gas-cooled reactors z) liquid-metal fast breeder reactors

Last Answer : ANSWER: W -- PRESSURIZED WATER REACTORS 

____________is the difference between the saturation temperature for the given pressure and the actual sub cooled liquid temperature.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Description : ____________is the difference between the saturation temperature for the given pressure and the actual sub cooled liquid temperature.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Last Answer : Degrees of Sub cooled, °SB

______________ is the temperature at which liquids start to boil or the temperature at which vapors begin to condense.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : ______________ is the temperature at which liquids start to boil or the temperature at which vapors begin to condense.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Saturation Temperature

The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Description : The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Last Answer : (B) Vapour density

The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Description : The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Last Answer : (A) Increase

Use of water as a manometric liquid suffers from the disadvantage of its (A) Low vapour pressure (B) Corrosive nature (C) High vapour pressure (D) High boiling point

Description : Use of water as a manometric liquid suffers from the disadvantage of its (A) Low vapour pressure (B) Corrosive nature (C) High vapour pressure (D) High boiling point

Last Answer : (C) High vapour pressure

Algae often float on surface of water during the day but sink down during the night due to (a) Evolution and trapping of oxygen bubbles during the day in their photosynthesis (b) Becoming light as they consume most of their food in the night (c) Warming action of sun during the day (d) Release of absorbed air by warming of water

Description : Algae often float on surface of water during the day but sink down during the night due to (a) Evolution and trapping of oxygen bubbles during the day in their photosynthesis (b) Becoming light as they ... (c) Warming action of sun during the day (d) Release of absorbed air by warming of water

Last Answer : Ans:(a)

An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Description : An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Last Answer : (C) Both (A) and (B)

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

When a liquid is at its boiling point, no temperature change takes place due to heating. The energy supplied due to heating (a) Is used up to increase the potential energy of the liquid molecules (b) Is used up to increase the kinetic energy of the molecules (c) Is used up to increase the kinetic energy and potential energy of the molecules (d) Is wasted

Description : When a liquid is at its boiling point, no temperature change takes place due to heating. The energy supplied due to heating (a) Is used up to increase the potential energy of the liquid molecules (b ... c) Is used up to increase the kinetic energy and potential energy of the molecules (d) Is wasted

Last Answer : Ans:(a)

Rate of heat transfer by vaporisation from pools of water is affected by the (A) Nature of heating surface and distribution of bubbles (B) Surface tension of water (C) Viscosity of water (D) All (A), (B) and (C)

Description : Rate of heat transfer by vaporisation from pools of water is affected by the (A) Nature of heating surface and distribution of bubbles (B) Surface tension of water (C) Viscosity of water (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following psychrometric processes is followed by water vapour laden unsaturated air, when it is passed through solid or liquid adsorbent? (A) Cooling and dehumidification (B) Heating and dehumidification at almost constant wet bulb temperature (C) Dehumidification with dry bulb temperature remaining constant (D) None of these

Description : Which of the following psychrometric processes is followed by water vapour laden unsaturated air, when it is passed through solid or liquid adsorbent? (A) Cooling and dehumidification ... (C) Dehumidification with dry bulb temperature remaining constant (D) None of these

Last Answer : (B) Heating and dehumidification at almost constant wet bulb temperature

Steady state temperature reached by a small amount of liquid evaporating into a large amount of unsaturated vapour-gas mixture is called the __________ temperature. (A) Dry-bulb (B) Wet-bulb (C) Dew point (D) Adiabatic saturation

Description : Steady state temperature reached by a small amount of liquid evaporating into a large amount of unsaturated vapour-gas mixture is called the __________ temperature. (A) Dry-bulb (B) Wet-bulb (C) Dew point (D) Adiabatic saturation

Last Answer : (B) Wet-bulb

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Description : One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Last Answer : Ans: d

Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film wise condensation (C) If a condensing liquid does not wet the surface dropwise, even then condensation will take place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Description : Pick out the correct statement about the condensation. (A) Filmwise condensation gives a lower heat transfer rate than the dropwise condensation (B) Suitable coating or vapour additive is used to promote film ... place on it (D) Reynolds number of condensing liquid is based on its mass flow rate

Last Answer : (B) Suitable coating or vapour additive is used to promote film wise condensation

The dew point is the: a. Dry bulb temperature on a psychrometer b. Temperature at which water vapour will start to be absorbed into the air c. Temperature below which water vapour will start to condense out of the air d. Pressure below which water vapour will start to condense out of the air e. Temperature at which water will start to evaporate

Description : The dew point is the: a. Dry bulb temperature on a psychrometer b. Temperature at which water vapour will start to be absorbed into the air c. Temperature below which water vapour will start to ... vapour will start to condense out of the air e. Temperature at which water will start to evaporate

Last Answer : Answer: C

Which of the following nuclear reactors is the most efficient thermodynamically while operating between the same temperature and pressure limits of the reactor? (A) Molten sodium cooled (B) CO2 gas cooled (C) Pressurised water (D) Boiling water

Description : Which of the following nuclear reactors is the most efficient thermodynamically while operating between the same temperature and pressure limits of the reactor? (A) Molten sodium cooled (B) CO2 gas cooled (C) Pressurised water (D) Boiling water

Last Answer : (D) Boiling water

Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of a system decreases with the evolution of heat (C) Change of internal energy is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Description : Pick out the wrong statement. (A) Surface tension of a substance vanishes at critical point, as there is no distinction between liquid and vapour phases at its critical point (B) Entropy of ... is negative for exothermic reactions (D) The eccentric factor for all materials is always more than one

Last Answer : (D) The eccentric factor for all materials is always more than one

__________ is the temperature at which a gas-vapor mixture becomes saturated, when cooled at constant total pressure out of contact with a liquid. (A) Dew point (B) Bubble point (C) Dry bulb temperature (D) Wet bulb temperature

Description : __________ is the temperature at which a gas-vapor mixture becomes saturated, when cooled at constant total pressure out of contact with a liquid. (A) Dew point (B) Bubble point (C) Dry bulb temperature (D) Wet bulb temperature

Last Answer : (A) Dew point

When vapour is cooled at constant total system volume, the _______ changes. A Volume. B PRESSURE C Temperature. D None of the mentioned.

Description : When vapour is cooled at constant total system volume, the _______ changes. A Volume. B PRESSURE C Temperature. D None of the mentioned.

Last Answer : B PRESSURE

When vapour is cooled at constant total system volume, the _______ changes. A] Volume. B] Pressure C] Temperature. D] None of the mentioned

Description : When vapour is cooled at constant total system volume, the _______ changes. A] Volume. B] Pressure C] Temperature. D] None of the mentioned

Last Answer : B] Pressure

A coalescer in a mixer-settler liquid-liquid extraction column (A) Comprises of thin bed of substances of extended surface having high porosity (B) Helps in increasing the bubble size entering the settler (C) Helps in increasing the settling rate of the bubbles (D) All 'a', 'b', & 'c'

Description :  A coalescer in a mixer-settler liquid-liquid extraction column (A) Comprises of thin bed of substances of extended surface having high porosity (B) Helps in increasing the bubble size entering the settler ... increasing the settling rate of the bubbles (D) All 'a', 'b', & 'c'

Last Answer : (D) All 'a', 'b', & 'c'

At boiling point of liquids, its : (1) Temperature increases (2) Atmospheric pressure increases (3) Timperature remains increases (4) Vapour pressure decreases

Description : At boiling point of liquids, its : (1) Temperature increases (2) Atmospheric pressure increases (3) Timperature remains increases (4) Vapour pressure decreases

Last Answer : (3) Timperature remains increases

At boiling point of liquids, its – (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Description : At boiling point of liquids, its – (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Last Answer : (3) Temperature remains constant Explanation: An interesting property of matter is that its temperature remains constant during a phase change, assuming its surrounding pressure is constant. A liquid changes into gaseous state at a constant temperature called its boiling point.

At boiling point of liquids, its (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Description : At boiling point of liquids, its (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases 

Last Answer : Temperature remains constant

At the critical point of a substance (A) The surface tension vanishes (B) Liquid and vapour have the same density (C) There is no distinction between liquid and vapour phases (D) All (A), (B) and (C)

Description : At the critical point of a substance (A) The surface tension vanishes (B) Liquid and vapour have the same density (C) There is no distinction between liquid and vapour phases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature (C) Double pipe heat exchangers are mostly used in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Description : Pick out the wrong statement. (A) Economy of a multiple effect evaporator is not influenced by the boiling point elevation (B) Two identical cubes of iron and copper will have the same heat ... in the field of refrigeration (D) Finned tube heat exchangers are suitable for heating air by steam

Last Answer : (B) Two identical cubes of iron and copper will have the same heat content under the same conditions of temperature

Moisture in a substance exerting an equilibrium vapour pressure less than that of pure liquid at the same temperature is called the __________ moisture. (A) Bound (B) Unbound (C) Critical (D) None of these

Description : Moisture in a substance exerting an equilibrium vapour pressure less than that of pure liquid at the same temperature is called the __________ moisture. (A) Bound (B) Unbound (C) Critical (D) None of these

Last Answer : (A) Bound

Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Description : Cavitation occurs in a centrifugal pump when the suction pressure is (A) Less than the vapour pressure of the liquid at that temperature (B) Greater than the vapour pressure of the liquid at that temperature (C) Equal to the vapour pressure (D) Equal to the developed head

Last Answer : (A) Less than the vapour pressure of the liquid at that temperature

Urea is formed only (A) In liquid phase (B) In vapour phase (C) At very high temperature (D) At very low pressure (vacuum)

Description : Urea is formed only (A) In liquid phase (B) In vapour phase (C) At very high temperature (D) At very low pressure (vacuum)

Last Answer : (A) In liquid phase

At triple point (for one component system), vapour pressure of solid as compared to that of liquid will be (A) More (B) Less (C) Same (D) More or less; depending on the system

Description : At triple point (for one component system), vapour pressure of solid as compared to that of liquid will be (A) More (B) Less (C) Same (D) More or less; depending on the system

Last Answer : (C) Same

Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward feeding in multiple effect evaporation (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Description : Vacuum is generally maintained in the vapour space of an evaporator mainly to (A) Get economical temperature difference by using moderate pressure steam (B) Facilitate forward ... (C) Concentrate heat sensitive materials (D) Achieve very high concentration of the final product

Last Answer : (A) Get economical temperature difference by using moderate pressure steam