Nucleate boiling is promoted (A) On polished surfaces (B) On rough surfaces (C) In the absence of agitation (D) None of these

Nucleate boiling is promoted
(A) On polished surfaces
(B) On rough surfaces
(C) In the absence of agitation
(D) None of these
by

1 Answer

Answer :

(B) On rough surfaces
by

Related questions

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

Dropwise condensation occurs on __________ surfaces. (A) Clean and dirt free (B) Smooth clean (C) Contaminated cooling (D) Polished

Description : Dropwise condensation occurs on __________ surfaces. (A) Clean and dirt free (B) Smooth clean (C) Contaminated cooling (D) Polished

Last Answer : (C) Contaminated cooling

A hot body will radiate heat most rapidly, if its surface is (A) White & rough (B) Black & rough (C) White & polished (D) Black & polished

Description : A hot body will radiate heat most rapidly, if its surface is (A) White & rough (B) Black & rough (C) White & polished (D) Black & polished

Last Answer : (B) Black & rough

In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Description : In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Last Answer : (B) Pool

When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Description : When vaporisation takes place directly at the heating surface, it is called (A) Film boiling (B) Nucleate boiling (C) Vapour binding (D) None of these

Last Answer : (B) Nucleate boiling

Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x (C) Distillation process is not the same as evaporation (D) The effectiveness of nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Description : Pick out the wrong statement. (A) In case of heat transfer by purely forced convection, GR /Re 2 ≤ 1 (B) The equivalent diameter of heat transfer for a duct of ... nucleate boiling depends basically on the ease with which the bubbles are formed and detached from the heating surface

Last Answer : (B) The equivalent diameter of heat transfer for a duct of square cross￾section (having each side as 'x') is equal to 4x

Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Description : Boiling of milk in an open vessel is an example of __________ boiling. (A) Film (B) Sub-cooled (C) Saturated nucleate (D) None of these

Last Answer : (A) Film

When vaporisation takes place through a blanketting film of gas, the phenomenon is termed as __________ boiling. (A) Pool (B) Nucleate (C) Transition (D) Film

Description : When vaporisation takes place through a blanketting film of gas, the phenomenon is termed as __________ boiling. (A) Pool (B) Nucleate (C) Transition (D) Film

Last Answer : (D) Film

In case of __________ boiling, the liquid temperature is below the saturation temperature and the boiling takes place in the vicinity of the heated surface. (A) Nucleate (B) Local (C) Pool (D) Saturated

Description : In case of __________ boiling, the liquid temperature is below the saturation temperature and the boiling takes place in the vicinity of the heated surface. (A) Nucleate (B) Local (C) Pool (D) Saturated

Last Answer : (B) Local

Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than that of the damp material (C) Ratio of its capacity to economy equals the steam consumption in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Description : Pick out the wrong statement. (A) Bubble size increases with the dynamic viscosity of the liquid in case of nucleate pool boiling (B) Thermal conductivity of a dry material is more than ... in kg/hr in an evaporator (D) Vaporisation of organic substances in evaporator mostly causes foam formation

Last Answer : (B) Thermal conductivity of a dry material is more than that of the damp material

Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation temperature of the liquid (C) Heat transfer from the surface of the liquid is less than that in film boiling (D) The temperature is less than that of film boiling

Description : Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation ... less than that in film boiling (D) The temperature is less than that of film boiling

Last Answer : (D) The temperature is less than that of film boiling

The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Description : The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Last Answer : (B) Vapour density

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Description : Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Last Answer : Option A

A heavy ladder resting on floor and against a vertical wall may not be in equilibrium, if (A) The floor is smooth, the wall is rough (B) The floor is rough, the wall is smooth (C) The floor and wall both are smooth surfaces (D) The floor and wall both are rough surfaces

Description : A heavy ladder resting on floor and against a vertical wall may not be in equilibrium, if (A) The floor is smooth, the wall is rough (B) The floor is rough, the wall is smooth (C) The floor and wall both are smooth surfaces (D) The floor and wall both are rough surfaces

Last Answer : (C) The floor and wall both are smooth surfaces

Infrared rays are absorbed best by which one of the following. Is it: w) bodies of air x) white bodies with rough surfaces y) mirrors z) black bodies with rough surfaces

Description : Infrared rays are absorbed best by which one of the following. Is it: w) bodies of air x) white bodies with rough surfaces y) mirrors z) black bodies with rough surfaces

Last Answer : ANSWER: Z -- BLACK BODIES WITH ROUGH SURFACES

Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The boiling point of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Description : Pick out the wrong statement. (A) Heat transfer from a hot body to cold body by the emission of heat waves is called radiation (B) Filmwise condensation takes place on non-wettable surfaces (C) The ... of a solution is affected by liquid head as well as boiling point elevation (D) None of these

Last Answer : (B) Filmwise condensation takes place on non-wettable surfaces

Embryo sac of angiosperm is : a) 6-celled 8-nucleate b) 7-celled 8-nucleate c)8-celled 7- nucleate d)7-celled 7-nucleate

Description : Embryo sac of angiosperm is : a) 6-celled 8-nucleate b) 7-celled 8-nucleate c)8-celled 7- nucleate d)7-celled 7-nucleate

Last Answer : Ans: b) 7-celled 8-nucleate

Formation of 8-nucleate embryosac by pollen grains is also called as

Description : Formation of 8-nucleate embryosac by pollen grains is also called as

Last Answer : Formation of 8-nucleate embryosac by pollen grains is also called as – Nemec phenomenon 

The most conducive surface for dropwise condensation to occur is the __________ surface. (A) Coated (B) Oily (C) Glazed & polished (D) Smooth

Description : The most conducive surface for dropwise condensation to occur is the __________ surface. (A) Coated (B) Oily (C) Glazed & polished (D) Smooth

Last Answer : (B) Oily

Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness (C) The emissivity of a polished surface is quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Description : Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness ... quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Last Answer : (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment

The thermal radiation emitted by a body is proportional to T n , where T is its absolute temperature. The value of 'n' is exactly 4 for (A) Black painted bodies only (B) All bodies (C) Polished bodies only (D) A black body

Description : The thermal radiation emitted by a body is proportional to T n , where T is its absolute temperature. The value of 'n' is exactly 4 for (A) Black painted bodies only (B) All bodies (C) Polished bodies only (D) A black body

Last Answer : (B) All bodies

The main reason for making the copper calorimeter (used in bomb calorimeter) silvery white and shining/polished is to (A) Minimise its corrosion (B) Avoid radiation heat loss (C) Make it look attractive (D) None of these

Description : The main reason for making the copper calorimeter (used in bomb calorimeter) silvery white and shining/polished is to (A) Minimise its corrosion (B) Avoid radiation heat loss (C) Make it look attractive (D) None of these

Last Answer : (B) Avoid radiation heat loss

Which of the following is not categorised as a "mechanical operation”? (A) Agitation (B) Filtration (C) Size enlargement (D) Humidification

Description : Which of the following is not categorised as a "mechanical operation”? (A) Agitation (B) Filtration (C) Size enlargement (D) Humidification

Last Answer : (D) Humidification

Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity(C) Surface tension(D) Density

Description : Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity (C) Surface tension (D) Density

Last Answer : (D) Density

Which of the following is not accomplished by agitation of liquids in agitators? (A) Dispersing gas in liquid (B) Blending of immiscible liquids (C) Dispersing immiscible liquid in form of emulsion (D) Suspending solid particles

Description : Which of the following is not accomplished by agitation of liquids in agitators? (A) Dispersing gas in liquid (B) Blending of immiscible liquids (C) Dispersing immiscible liquid in form of emulsion (D) Suspending solid particles

Last Answer : (B) Blending of immiscible liquids

During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Last Answer : (A) Density of the liquid

About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ

Description : About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ

Last Answer : (A) P. gc /n 3 . D2 . ρ

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Laminar flow region is said to exist during agitation of a liquid in an agitator, when the value of Reynolds number is (A) > 10 (B) < 10 (C) > 100 (D) < 100

Description : Laminar flow region is said to exist during agitation of a liquid in an agitator, when the value of Reynolds number is (A) > 10 (B) < 10 (C) > 100 (D) < 100

Last Answer : (B) < 10

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

Leaching rate is independent of the (A) Agitation (B) Temperature (C) Particle size (D) None of these

Description : Leaching rate is independent of the (A) Agitation (B) Temperature (C) Particle size (D) None of these

Last Answer : (D) None of these

Leaching of coarse solid lumps is also termed as(A) Decoction (B) Dissolution (C) Percolation (D) Agitation and settling

Description : Leaching of coarse solid lumps is also termed as (A) Decoction (B) Dissolution (C) Percolation (D) Agitation and settling

Last Answer : (C) Percolation

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

Does the statue of liberty need to be polished? (Details inside )

Description : Does the statue of liberty need to be polished? (Details inside )

Last Answer : answer:Yes, they could. Copper (when near oxygen) eventually makes the chemical copper oxide, which has a greenish color. That, and carbon in the atmosphere, eventually turn into copper carbonate. The copper ... statue by exposing raw copper, and finally because it would cost a hell of a lot to do.

Can you varnish over polished wood?

Description : Can you varnish over polished wood?

Last Answer : answer:My web searches for Fabulustre are turning up a metal polishing compound. Polishing compounds like this are very fine abrasive particles in a matrix of wax or grease. If this is what was used, then ... would adhere well to that, because it will still be able to enter the grain of the wood.

At what point would a car benefit from being buffed and polished?

Description : At what point would a car benefit from being buffed and polished?

Last Answer : answer:First, any car that is painted red should be polished and waxed at least every 6 months. its called oxidation. Most more expensive cars come with a clearcoat finish on it, from the factory. these vehicles do ... on it and gets a car wash and wax at least every two weeks. I say go for it.

Can a polished display be polished to a gloss?

Last Answer : Locally where, I don't know, maybe some phone specialty store. But here's a video on how to make it at home: https://www.youtube.com/watch?v=Ciw_TnA62FQ

how do I keep the veneer finish on my wood furniture from yellowing when polished?

Description : how do I keep the veneer finish on my wood furniture from yellowing when polished?

Last Answer : Need Answer

What are the uses of Polished Tumbled Stones?

Description : What are the uses of Polished Tumbled Stones?

Last Answer : Polish tumbled stones are naturally beautiful materials that can be shaped and polished even more beautifully. Tumbled stones uses are quite varied because of their affordability and abundance. You can use them as home décor, personalized gifts, jewelry, crafts, meditation and spiritual healing.

Why are marble faced buildings made with marble that has been polished?

Description : Why are marble faced buildings made with marble that has been polished?

Last Answer : Purely aesthetics - it makes the building 'look nice'.

Why are marble faced buildings made with marble that has been polished?

Description : Why are marble faced buildings made with marble that has been polished?

Last Answer : Purely aesthetics - it makes the building 'look nice'.

Does anyone know where I can get my car polished?

Description : Does anyone know where I can get my car polished?

Last Answer : You can get your car polished at any car wash. You can also take your car to a dealership where you purchased the car and they will also wash it and polish it for you as well.

Niacin deficiency is common in people whose staple food is (A) Wheat (B) Polished rice (C) Maize and /or sorghum (D) None of these

Description : Niacin deficiency is common in people whose staple food is (A) Wheat (B) Polished rice (C) Maize and /or sorghum (D) None of these

Last Answer : Answer : C

People consuming polished rice as their staple food are prone to (A) Beriberi (B) Pellagra (C) Both (A) and (B) (D) None of these

Description : People consuming polished rice as their staple food are prone to (A) Beriberi (B) Pellagra (C) Both (A) and (B) (D) None of these

Last Answer : Answer : A

In countries where polished rise is the main cereal in their diet, people suffer from (a) pellagra (b) scurvy (c) beriberi (d) osteomalacia

Description : In countries where polished rise is the main cereal in their diet, people suffer from (a) pellagra (b) scurvy (c) beriberi (d) osteomalacia

Last Answer : Ans:(a)

The base of an electric iron is brightly polished mainly - (1) to make it smooth and frictionless (2) to make it rust-proof (3) to reduce heat loss by radiation (4) to make it more durable

Description : The base of an electric iron is brightly polished mainly - (1) to make it smooth and frictionless (2) to make it rust-proof (3) to reduce heat loss by radiation (4) to make it more durable

Last Answer : (3) to reduce heat loss by radiation Explanation: Polished surfaces are poor radiators of heat. So loss of heat on that account is reduced and the electric iron remains hotter than otherwise.

The base of an electric iron is brightly polished mainly - (1) to make it smooth and frictionless (2) to make it rust-proof (3) to reduce heat loss by radiation (4) to make it more durable

Description : The base of an electric iron is brightly polished mainly - (1) to make it smooth and frictionless (2) to make it rust-proof (3) to reduce heat loss by radiation (4) to make it more durable

Last Answer : (3) to reduce heat loss by radiation Explanation: Polished surfaces are poor radiators of heat. So loss of heat on that account is reduced and the electric iron remains hotter than otherwise.

Copper is often used as an electrical conductor because it _______________. A. has high resistance at low temperatures B. has a highly polished surface C. is able to pass current with little opposition D. holds insulation together well

Description : Copper is often used as an electrical conductor because it _______________. A. has high resistance at low temperatures B. has a highly polished surface C. is able to pass current with little opposition D. holds insulation together well

Last Answer : Answer: C

Why rate of condensation is higher on a polished surface compared to rusty surface ?

Description : Why rate of condensation is higher on a polished surface compared to rusty surface ?

Last Answer : Polished surface promotes drop wise condensation and does not wet the surface.

How do you reduce the loss that is produced when light strikes a flat polished end of a fiber optic? A. By painting the surface B. By inclining the surface C. By cooling D. By application of antireflection coating

Description : How do you reduce the loss that is produced when light strikes a flat polished end of a fiber optic? A. By painting the surface B. By inclining the surface C. By cooling D. By application of antireflection coating

Last Answer : D. By application of antireflection coating