An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

An ideal liquid refrigerant should
(A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils
(B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B)
(D) Have low specific heat
by

1 Answer

Answer :

(C) Both (A) and (B)
by

Related questions

Which of the following is an undesirable characteristic of a refrigerant? (A) It should be non-explosive (B) It should have a sub-atmospheric vapor pressure at the temperature in refrigerator coils (C) Its vapor pressure at the condenser temperature should be very high (D) None of these

Description : Which of the following is an undesirable characteristic of a refrigerant? (A) It should be non-explosive (B) It should have a sub-atmospheric vapor pressure at the temperature in refrigerator coils (C) Its vapor pressure at the condenser temperature should be very high (D) None of these

Last Answer : (B) It should have a sub-atmospheric vapor pressure at the temperature in refrigerator coils

In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: d

Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at 35°C (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C (C) Boiling brine kept in open vessel when the bottom surface temperature of the vessel is maintained constant at 180°C (D) A sub-cooled refrigerant liquid at 8°C flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C

Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C

In refrigerator, liquid receiver is required between condenser and flow controlling device, if quantity of refrigerant for system is (a) less than 2 kg (b) more than or equal to 3.65 kg (c) more than 10 kg (d) there is no such consideration

Description : In refrigerator, liquid receiver is required between condenser and flow controlling device, if quantity of refrigerant for system is (a) less than 2 kg (b) more than or equal to 3.65 kg (c) more than 10 kg (d) there is no such consideration

Last Answer : Ans: b

In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Description : In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Last Answer : Ans: c

In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Last Answer : Ans: a

Lowering of condenser temperature (keeping the evaporator temperature constant) in case of vapour compression refrigeration system results in (A) Increased COP (B) Same COP (C) Decreased COP (D) Increased or decreased COP; depending upon the type of refrigerant

Description : Lowering of condenser temperature (keeping the evaporator temperature constant) in case of vapour compression refrigeration system results in (A) Increased COP (B) Same COP (C) Decreased COP (D) Increased or decreased COP; depending upon the type of refrigerant

Last Answer : (A) Increased COP

One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Description : One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

Last Answer : Ans: d

In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Description : In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Last Answer : Ans: a

Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Description : Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Last Answer : Ans: a

Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of vaporisation is constant (C) Volume in the liquid state is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Description : Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of ... is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Description : In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Last Answer : Ans: d

The bank of tubes at the back of domestic refrigerator are (a) condenser tubes (b) evaporator tubes (c) refrigerant cooling tubes (d) capillary tubes

Description : The bank of tubes at the back of domestic refrigerator are (a) condenser tubes (b) evaporator tubes (c) refrigerant cooling tubes (d) capillary tubes

Last Answer : Ans: a

In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Description : In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Last Answer : Ans: D

In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Description : In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Last Answer : Ans: b

In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: c

The vapour pressure of refrigerant should be (a) lower than atmospheric pressure (b) higher than atmospheric pressure (c) equal to atmospheric pressure (d) could be anything

Description : The vapour pressure of refrigerant should be (a) lower than atmospheric pressure (b) higher than atmospheric pressure (c) equal to atmospheric pressure (d) could be anything

Last Answer : Ans: b

The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Description : The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Last Answer : Ans: d

The refrigerant for a refrigerator should have (a) high sensible heat (b) high total heat (c) high latent heat (d) low latent heat

Description : The refrigerant for a refrigerator should have (a) high sensible heat (b) high total heat (c) high latent heat (d) low latent heat

Last Answer : Ans: c

Choose the correct statement (a) A refrigerant should have low latent heat (b) If operating temperature of system is low, then refrigerant with low boiling point should be used (c) Pre-cooling and sub-cooling bf refrigerant are same (d) Superheat and sensible heat of a. refrigerant are same

Description : Choose the correct statement (a) A refrigerant should have low latent heat (b) If operating temperature of system is low, then refrigerant with low boiling point should be used (c) Pre-cooling and sub-cooling bf refrigerant are same (d) Superheat and sensible heat of a. refrigerant are same

Last Answer : Ans: b

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Description : In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Last Answer : Ans: c

Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Description : Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Last Answer : Ans: d

The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Description : The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Last Answer : Ans: b

To obtain integrated form of Clausius-Clapeyron equation, ln (P2/P1) = (∆HV/R) (1/T1- 1/T2) from the exact Clapeyron equation, it is assumed that the (A) Volume of the liquid phase is negligible compared to that of vapour phase (B) Vapour phase behaves as an ideal gas (C) Heat of vaporisation is independent of temperature (D) All (A), (B) & (C)

Description : To obtain integrated form of Clausius-Clapeyron equation, ln (P2/P1) = (∆HV/R) (1/T1- 1/T2) from the exact Clapeyron equation, it is assumed that the (A) Volume of the liquid phase is negligible compared to ... gas (C) Heat of vaporisation is independent of temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

A liquid under pressure greater than its vapour pressure for the temperature involved is called a __________ liquid. (A) Sub-cooled (B) Saturated (C) Non-solidifiable (D) None of these

Description : A liquid under pressure greater than its vapour pressure for the temperature involved is called a __________ liquid. (A) Sub-cooled (B) Saturated (C) Non-solidifiable (D) None of these

Last Answer : (A) Sub-cooled

For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should be used (c) perfectly tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Description : For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should ... tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Last Answer : Ans: c

For better COP of refrigerator, the pressure range corresponding to temperature in evaporator and condenser must be (a) small (b) high (c) equal (d) anything

Description : For better COP of refrigerator, the pressure range corresponding to temperature in evaporator and condenser must be (a) small (b) high (c) equal (d) anything

Last Answer : Ans: a

Which of the following is a widely used refrigerant in vapour compression refrigeration system (using large centrifugal compressor)? (A) Freon (B) Liquid sulphur dioxide (C) Methyl chloride (D) Ammonia

Description : Which of the following is a widely used refrigerant in vapour compression refrigeration system (using large centrifugal compressor)? (A) Freon (B) Liquid sulphur dioxide (C) Methyl chloride (D) Ammonia

Last Answer : (A) Freon

5. In "Imperial Smelting Process" for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following: (A) Jet of water at high pressure (B) Blast of air (C) Mixture of water and air (D) Rain of molten lead

Description : 5. In "Imperial Smelting Process" for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following: (A) Jet of water at high pressure (B) Blast of air (C) Mixture of water and air (D) Rain of molten lead

Last Answer : Option D

The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Description : The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Last Answer : Ans: a

The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Description : The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Last Answer : Ans: a

Which one of the following statements is correct ? a) For water at 100o Celsius at sea level, the vapour pressure is equal to atmospheric pressure b) Surface energy (or tension) is caused by the force of adhesion between liquid molecules c) Viscosity of a fluid is the property exhibited by it both in static and in dynamic conditions d) Air is 50,000 times more compressible than water

Description : Which one of the following statements is correct ? a) For water at 100o Celsius at sea level, the vapour pressure is equal to atmospheric pressure b) Surface energy (or tension) is caused by ... it both in static and in dynamic conditions d) Air is 50,000 times more compressible than water

Last Answer : c) Viscosity of a fluid is the property exhibited by it both in static and in dynamic conditions

LMTD can't be used as such without a correction factor for the (A) Multipass heat exchanger (B) Baffled heat exchanger (C) Condensation of mixed vapour in a condenser (D) All (A) (B) and (C)

Description : LMTD can't be used as such without a correction factor for the (A) Multipass heat exchanger (B) Baffled heat exchanger (C) Condensation of mixed vapour in a condenser (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

Urea is formed only (A) In liquid phase (B) In vapour phase (C) At very high temperature (D) At very low pressure (vacuum)

Description : Urea is formed only (A) In liquid phase (B) In vapour phase (C) At very high temperature (D) At very low pressure (vacuum)

Last Answer : (A) In liquid phase

In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) Bubbles from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Description : In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) ... from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Last Answer : (B) Temperature of the heating surface is more than the boiling point of the liquid

The bank of tubes located at the back of the domestic refrigerators are the __________ tubes. (A) Refrigerant cooling (B) Evaporator (C) Condenser (D) Throttling

Description : The bank of tubes located at the back of the domestic refrigerators are the __________ tubes. (A) Refrigerant cooling (B) Evaporator (C) Condenser (D) Throttling

Last Answer : C) Condenser

Activity co-efficient is a measure of the (A) Departure from ideal solution behaviour (B) Departure of gas phase from ideal gas law (C) Vapour pressure of liquid (D) None of these

Description : Activity co-efficient is a measure of the (A) Departure from ideal solution behaviour (B) Departure of gas phase from ideal gas law (C) Vapour pressure of liquid (D) None of these

Last Answer : (A) Departure from ideal solution behaviour

The effect of changing the evaporator temperature on COP as compared to that of changing the condenser temperature (in vapour compression refrigeration system) is (A) Less pronounced (B) More pronounced (C) Equal (D) Data insufficient, can't be predicted

Description : The effect of changing the evaporator temperature on COP as compared to that of changing the condenser temperature (in vapour compression refrigeration system) is (A) Less pronounced (B) More pronounced (C) Equal (D) Data insufficient, can't be predicted

Last Answer : (B) More pronounced

In vapour compression refrigeration system, if the evaporator temperature and the condenser temperatures are -13°C and 37°C respectively, the Carnot COP will be (A) 5.2 (B) 6.2 (C) 0.168 (D) Data insufficient, can't be found out

Description : In vapour compression refrigeration system, if the evaporator temperature and the condenser temperatures are -13°C and 37°C respectively, the Carnot COP will be (A) 5.2 (B) 6.2 (C) 0.168 (D) Data insufficient, can't be found out

Last Answer : A) 5.2

Identify modes of heat transfer involved applications with brief explanation. (1) Radiator of automobile (2) Condenser of domestic refrigerator.

Description : Identify modes of heat transfer involved applications with brief explanation. (1) Radiator of automobile (2) Condenser of domestic refrigerator.

Last Answer : Modes of heat transfer Automobile radiator-A radiator is a type of heat exchanger. It is designed to transfer heat from the hot coolant that flows through it to the air blown through ... of heat transfer plays very important deciding factor transferring heat from condenser tube to atmosphere.  

What happens to a liquid, when the vapour pressure equals the atmospheric pressure? (1) The liquid cools (2) The liquid boils (3) No change (4) The liquid evaporates

Description : What happens to a liquid, when the vapour pressure equals the atmospheric pressure? (1) The liquid cools (2) The liquid boils (3) No change (4) The liquid evaporates

Last Answer : (2) The liquid boils Explanation: Ordinary evaporation is a surface phenomenon -since the vapor pressure is low and since the pressure inside the liquid is equal to atmospheric pressure plus ... pressure is equal to atmospheric pressure, bubbles form, and the vaporization becomes a volume phenomena.

What happens to a liquid, when the vapour pressure equals the atmospheric pressure? (1) The liquid cools (2) The liquid boils (3) No change (4) The liquid evaporates

Description : What happens to a liquid, when the vapour pressure equals the atmospheric pressure? (1) The liquid cools (2) The liquid boils (3) No change (4) The liquid evaporates

Last Answer : The liquid boils

The formation of frost on cooling coils in a refrigerator (a) increases heat transfer (b) improves C.O.P. of the system (c) increases power consumption (d) reduces power consumption

Description : The formation of frost on cooling coils in a refrigerator (a) increases heat transfer (b) improves C.O.P. of the system (c) increases power consumption (d) reduces power consumption

Last Answer : Ans: c

High __________ is an undesirable property for a good refrigerant. (A) Specific heat (B) Latent heat of vaporisation (C) Viscosity (D) Specific vapor volume

Description : High __________ is an undesirable property for a good refrigerant. (A) Specific heat (B) Latent heat of vaporisation (C) Viscosity (D) Specific vapor volume

Last Answer : (C) Viscosity

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only

In order to obtain spectrum from the emitted radiation, the atomic gas or vapour must be excited at a) much less than atmospheric pressure b) much high than atmospheric pressure c) atmospheric pressure d) high pressure and temperature

Description : In order to obtain spectrum from the emitted radiation, the atomic gas or vapour must be excited at a) much less than atmospheric pressure b) much high than atmospheric pressure c) atmospheric pressure d) high pressure and temperature

Last Answer : a) much less than atmospheric pressure

Water always boils when its (A) Temperature reaches 100° C (B) Vapour pressure equals 76 cm of Hg (C) Saturated vapour pressure equals the external pressure on its surface (D) Saturated vapour pressure is less than the atmospheric pressure

Description : Water always boils when its (A) Temperature reaches 100° C (B) Vapour pressure equals 76 cm of Hg (C) Saturated vapour pressure equals the external pressure on its surface (D) Saturated vapour pressure is less than the atmospheric pressure

Last Answer : (C) Saturated vapour pressure equals the external pressure on its surface