One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve

One of the purposes of sub-cooling the liquid refrigerant is to (a) reduce compressor overheating (b) reduce compressor discharge temperature (c) increase cooling effect (d) ensure that only liquid and not the vapour enters the expansion (throttling) valve
by

1 Answer

Answer :

Ans: d
by
selected by

Related questions

In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Description : In vapour compression refrigeration system, refrigerant occurs as liquid between (a) condenser and expansion valve (b) compressor and evaporator (c) expansion valve and evaporator (d) compressor and condenser

Last Answer : Ans: c

In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Description : In a vapour compression cycle, the refrigerant immediately after expansion valve is (a) liquid (b) sub-cooled liquid (c) saturated liquid (d) wet vapour

Last Answer : Ans: d

In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Description : In vapour compression cycle the condition off refrigerant is dry saturated vapour (a) after passing through the condenser (b) before passing through the condenser (c)before entering the expansion valve (d) before entering the compressor

Last Answer : Ans: D

The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Description : The higher temperature in vapour compression cycle occurs at (a) compressor discharge. (b) expansion valve (c) evaporator (d) condenser discharge

Last Answer : Ans: a

In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Description : In a flooded evaporator refrigerator, an accumulator at suction of compressor is used to (a) collect liquid refrigerant and prevent it from going to compressor (b) detect liquid in vapour (c) superheat the vapour (d) increase refrigeration effect

Last Answer : Ans: a

The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Description : The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Last Answer : Ans: d

In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is high pressure saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: d

In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is saturated liquid (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion throttle valve (d) before entering the expansion valve

Last Answer : Ans: a

Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Description : Domestic refrigerator working on vapour compression cycle uses the following type of expansion device (a) electrically operated throttling valve (b) manually operated valve (c) thermostatic valve (d) capillary tube

Last Answer : Ans: d

In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Description : In a refrigeration cycle, the flow of refrigerant is controlled by (a) compressor (b) condenser (c) evaporator (d) expansion valve

Last Answer : Ans: d

Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Description : Presence of moisture in a refrigerant affects the working of (a) compressor (b) condenser (c) evaparator (d) expansion valve.

Last Answer : Ans: a

Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Description : Where does the lowest temperature occur in a vapour compression cycle ? (a) condenser (b) evaporator (c) compressor (d) expansion valve

Last Answer : Ans: b

In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Description : In vapour compression cycle the condition of refrigerant is superheated vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) beforeentering the expansion valve

Last Answer : Ans: b

In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Description : In vapour compression cycle, the condition of refrigerant is very wet vapour (a) after passing through the condenser (b) before passing through the condenser (c) after passing through the expansion or throttle valve (d) before entering the expansion valve

Last Answer : Ans: c

In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Description : In vapour compression cycle using NH3 as refrigerant, initial charge is filled at (a) suction of compressor (b) delivery of compressor (c) high pressure side close to receiver (d) low pressure side near receiver

Last Answer : Ans: c

Choose the correct statement (a) A refrigerant should have low latent heat (b) If operating temperature of system is low, then refrigerant with low boiling point should be used (c) Pre-cooling and sub-cooling bf refrigerant are same (d) Superheat and sensible heat of a. refrigerant are same

Description : Choose the correct statement (a) A refrigerant should have low latent heat (b) If operating temperature of system is low, then refrigerant with low boiling point should be used (c) Pre-cooling and sub-cooling bf refrigerant are same (d) Superheat and sensible heat of a. refrigerant are same

Last Answer : Ans: b

The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Description : The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Last Answer : Ans: d

Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Description : Condensing temperature in a refrigerator is the temperature (a) of cooling medium (b) of freezing zone (c) of evaporator (d) at which refrigerant gas becomes liquid

Last Answer : Ans: d

The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Description : The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Last Answer : Ans: b

For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should be used (c) perfectly tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Description : For proper refrigeration in a cabinet, if the temperature and vapour pressure difference between cabinet and atmosphereis high, then (a) bigger cabinet should be used (b) smaller cabinet should ... tight vapour seal should be used (d) refrigerant with lower evaporation temperature should be used

Last Answer : Ans: c

Adiabatic compression is one in which A. Temperature during compression remains constant B. No heat leaves or enters the compressor cylinder during compression C. Temperature rise follows a linear relationship D. Work done is maximum.

Description : Adiabatic compression is one in which A. Temperature during compression remains constant B. No heat leaves or enters the compressor cylinder during compression C. Temperature rise follows a linear relationship D. Work done is maximum.

Last Answer : ANSWER : B

Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Description : Reducing suction pressure in refrigeration cycle (a) lowers evaporation temperature (b) increases power required per ton of refrigeration (c) lowers compressor capacity because vapour is lighter (d) all of the above.

Last Answer : Ans: d

Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Description : Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Last Answer : Ans: a

The vapour pressure of refrigerant should be (a) lower than atmospheric pressure (b) higher than atmospheric pressure (c) equal to atmospheric pressure (d) could be anything

Description : The vapour pressure of refrigerant should be (a) lower than atmospheric pressure (b) higher than atmospheric pressure (c) equal to atmospheric pressure (d) could be anything

Last Answer : Ans: b

The moisture in a refrigerant is removed by (a) evaporator (b) safety relief valve (c) dehumidifier (d) driers

Description : The moisture in a refrigerant is removed by (a) evaporator (b) safety relief valve (c) dehumidifier (d) driers

Last Answer : Ans: d

An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Description : An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Last Answer : (C) Both (A) and (B)

Which of the following is a widely used refrigerant in vapour compression refrigeration system (using large centrifugal compressor)? (A) Freon (B) Liquid sulphur dioxide (C) Methyl chloride (D) Ammonia

Description : Which of the following is a widely used refrigerant in vapour compression refrigeration system (using large centrifugal compressor)? (A) Freon (B) Liquid sulphur dioxide (C) Methyl chloride (D) Ammonia

Last Answer : (A) Freon

The bank of tubes at the back of domestic refrigerator are (a) condenser tubes (b) evaporator tubes (c) refrigerant cooling tubes (d) capillary tubes

Description : The bank of tubes at the back of domestic refrigerator are (a) condenser tubes (b) evaporator tubes (c) refrigerant cooling tubes (d) capillary tubes

Last Answer : Ans: a

Reciprocating compressor are provided with A. Simple disc/plate valve B. Poppet valve C. Spring-loaded disc valve D. Solenoid valve.

Description : Reciprocating compressor are provided with A. Simple disc/plate valve B. Poppet valve C. Spring-loaded disc valve D. Solenoid valve.

Last Answer : ANSWER : A

The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Description : The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Last Answer : Ans: a

The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Description : The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Last Answer : Ans: a

The bank of tubes located at the back of the domestic refrigerators are the __________ tubes. (A) Refrigerant cooling (B) Evaporator (C) Condenser (D) Throttling

Description : The bank of tubes located at the back of the domestic refrigerators are the __________ tubes. (A) Refrigerant cooling (B) Evaporator (C) Condenser (D) Throttling

Last Answer : C) Condenser

In multi stage compressor, the isothermal compression is achieved by A. Employing intercooler B. By constantly cooling the cylinder C. By running compressor at very slow speed D. By insulating the cylinder

Description : In multi stage compressor, the isothermal compression is achieved by A. Employing intercooler B. By constantly cooling the cylinder C. By running compressor at very slow speed D. By insulating the cylinder

Last Answer : ANSWER : C

Which one of the following methods can be adopted to obtain isothermal compression in an air compressor? A. Increasing the weight of the compressor B. Inter-stage heating C. Atmospheric cooling D. Providing appropriate dimensions to the cylinder

Description : Which one of the following methods can be adopted to obtain isothermal compression in an air compressor? A. Increasing the weight of the compressor B. Inter-stage heating C. Atmospheric cooling D. Providing appropriate dimensions to the cylinder

Last Answer : ANSWER : A

In refrigerator, liquid receiver is required between condenser and flow controlling device, if quantity of refrigerant for system is (a) less than 2 kg (b) more than or equal to 3.65 kg (c) more than 10 kg (d) there is no such consideration

Description : In refrigerator, liquid receiver is required between condenser and flow controlling device, if quantity of refrigerant for system is (a) less than 2 kg (b) more than or equal to 3.65 kg (c) more than 10 kg (d) there is no such consideration

Last Answer : Ans: b

The basic function of air dryer in a compressor is: a. prevent dust from entering compressor b. storage and smoothening pulsating air output c. reduce the temperature of the air before it enters the next state to increase efficiency d. to remove remaining traces of moisture after after-cooler

Description : The basic function of air dryer in a compressor is: a. prevent dust from entering compressor b. storage and smoothening pulsating air output c. reduce the temperature of the air before it enters the next state to increase efficiency d. to remove remaining traces of moisture after after-cooler 

Last Answer : d. to remove remaining traces of moisture after after-cooler 

What is sensible cooling of air? A. the cooling in which sensible heat of air is removed in order to reduce temperature B. the cooling in which temperature of air is reduced without changing in its moisture content C. both a. and b. D. none of the above

Description : What is sensible cooling of air? A. the cooling in which sensible heat of air is removed in order to reduce temperature B. the cooling in which temperature of air is reduced without changing in its moisture content C. both a. and b. D. none of the above

Last Answer : ANSWER : C

Clapeyron equation is applicable for registration at (a) saturation point of vapour (b) saturation point of liquid (c) sublimation temperature (d) triple point.

Description : Clapeyron equation is applicable for registration at (a) saturation point of vapour (b) saturation point of liquid (c) sublimation temperature (d) triple point.

Last Answer : Ans: a

If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Description : If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Last Answer : ANSWER : B

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

If a gas vapour is allowed to expand through a very minute aperture, then such a process is known as  (a) free expansion  (b) hyperbolic expansion  (c) adiabatic expansion  (d) parabolic expansion  (e) throttling.

Description : If a gas vapour is allowed to expand through a very minute aperture, then such a process is known as  (a) free expansion  (b) hyperbolic expansion  (c) adiabatic expansion  (d) parabolic expansion  (e) throttling.

Last Answer : Answer : e

In refrigerators, the temperature difference between the evaporating refrigerant and the medium being cooled should be (a) high, of the order of 25° (b) as low as possible (3 to 11°C) (c) zero (d) any value

Description : In refrigerators, the temperature difference between the evaporating refrigerant and the medium being cooled should be (a) high, of the order of 25° (b) as low as possible (3 to 11°C) (c) zero (d) any value

Last Answer : Ans: b

Highest temperature encountered in refrigeration cycle should be (a) near critical temperature of refrigerant (b) above critical temperature (c) atcritica. temperature (d) much below critical temperature

Description : Highest temperature encountered in refrigeration cycle should be (a) near critical temperature of refrigerant (b) above critical temperature (c) atcritica. temperature (d) much below critical temperature

Last Answer : Ans: d

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

Claude gas liquefaction process employs cooling (A) At constant pressure (B) By throttling (C) By expansion in an engine (D) None of these

Description : Claude gas liquefaction process employs cooling (A) At constant pressure (B) By throttling (C) By expansion in an engine (D) None of these

Last Answer : (C) By expansion in an engine

Linde gas liquefaction process employs cooling (A) By throttling (B) By expansion in an engine (C) At constant pressure (D) None of these

Description : Linde gas liquefaction process employs cooling (A) By throttling (B) By expansion in an engine (C) At constant pressure (D) None of these

Last Answer : (A) By throttling

Claude's liquefaction process employs the cooling of gases by (A) Expansion in an engine (B) Following a constant pressure cycle (C) Throttling (D) None of these

Description : Claude's liquefaction process employs the cooling of gases by (A) Expansion in an engine (B) Following a constant pressure cycle (C) Throttling (D) None of these

Last Answer : A) Expansion in an engine

The reason for supercharging in any engine is to be A. increase efficiency B. increase power C. effect fuel economy D. reduce weight and bulk for a given output

Description : The reason for supercharging in any engine is to be A. increase efficiency B. increase power C. effect fuel economy D. reduce weight and bulk for a given output

Last Answer : ANSWER : D

Critical pressure of a liquid is the pressure (a) above which liquid will remain liquid (b) above which liquid becomes gas (c) above which liquid becomes vapour (d) above which liquid becomes solid

Description : Critical pressure of a liquid is the pressure (a) above which liquid will remain liquid (b) above which liquid becomes gas (c) above which liquid becomes vapour (d) above which liquid becomes solid

Last Answer : Ans: a

Vapour lock is a. complete or partial stoppage of fuel supply due to vaporization of the fuel b. locking of carburetor due to high vapor pressure c. excess fuel supply to the engine d. supply of liquid fuel to the engine

Description : Vapour lock is a. complete or partial stoppage of fuel supply due to vaporization of the fuel b. locking of carburetor due to high vapor pressure c. excess fuel supply to the engine d. supply of liquid fuel to the engine

Last Answer : ANSWER a. complete or partial stoppage of fuel supply due to vaporization of the fuel