During the first stage of triaxial test when the cell pressure is increased from 0.10 N/mm² to 0.26 N/mm², the pore water pressure increases from 0.07 N/mm² to 0.15 N/mm². Skempton's pore B (A) 0.5 (B) -0.5 (C) 2.0 (D) -2.0

During the first stage of triaxial test when the cell pressure is increased from 0.10 N/mm² to 0.26
N/mm², the pore water pressure increases from 0.07 N/mm² to 0.15 N/mm². Skempton's pore
B
(A) 0.5
(B) -0.5
(C) 2.0
(D) -2.0
by

1 Answer

Answer :

(A) 0.5
by

Related questions

For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Description : For shear strength, triaxial shear test is suitable because (A) It can be performed under all three drainage conditions (B) Precise measurement of the pore pressure and volume change during the test is possible (C) Stress distribution on the failure plane, is uniform (D) All the above

Last Answer : (D) All the above

A triaxial shear test is preferred to direct shear test, because (A) It can be performed under all three drainage conditions with complete control (B) Precise measurement of pore pressure and change in volume during test, is not possible (C) Stress distribution on the failure plane, is non uniform (D) None of these

Description : A triaxial shear test is preferred to direct shear test, because (A) It can be performed under all three drainage conditions with complete control (B) Precise measurement of pore pressure and change in ... possible (C) Stress distribution on the failure plane, is non uniform (D) None of these

Last Answer : Answer: Option A

Skempton's pore pressure coefficient B for saturated soil is (A) 1 (B) Zero (C) Between 0 and 1 (D) Greater than 1

Description : Skempton's pore pressure coefficient B for saturated soil is (A) 1 (B) Zero (C) Between 0 and 1 (D) Greater than 1

Last Answer : Answer: Option A

In a triaxial compression test when drainage is allowed during the first stage (i. e. application of cell pressure) only and not during the second stage (i.e. application of deviator stress at constant cell pressure), the test is known as (A) Consolidated drained test (B) Consolidated undrained test (C) Unconsolidated drained test (D) Unconsolidated undrained test

Description : In a triaxial compression test when drainage is allowed during the first stage (i. e. application of cell pressure) only and not during the second stage (i.e. application of deviator ... test (B) Consolidated undrained test (C) Unconsolidated drained test (D) Unconsolidated undrained test

Last Answer : (B) Consolidated undrained test

A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm

Last Answer : (C) 50 mm

If drainage is permitted throughout the test, during the application of both normal, and shear stresses so that full consolidation occurs and no excess pore pressure is set up at any stage of the test, is known as (A) Quick test (B) Drained test (C) Consolidated undrained test (D) None of these

Description : If drainage is permitted throughout the test, during the application of both normal, and shear stresses so that full consolidation occurs and no excess pore pressure is set up at any stage of the test, is ... (A) Quick test (B) Drained test (C) Consolidated undrained test (D) None of these

Last Answer : Answer: Option B

Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct shear test (C) The confining pressure is maximum during an unconfined compression test (D) The cylindrical specimen of a soil is subjected to major principal stress till it fails due to shearing along the plane of the failure

Description : Pick up the correct statement from the following: (A) An unconfined compression test is a special case of triaxial compression test (B) An unconfined compression test is a special case of direct ... subjected to major principal stress till it fails due to shearing along the plane of the failure

Last Answer : Option A

Crushing strength of a first class brick should not be less than (A) 3.5 N/mm² (B) 7.0 N/mm² (C) 10.5 N/mm² (D) 14.0 N/mm²

Description : Crushing strength of a first class brick should not be less than (A) 3.5 N/mm² (B) 7.0 N/mm² (C) 10.5 N/mm² (D) 14.0 N/mm²

Last Answer : Answer: Option C

A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of internal friction for the soil are respectively (A) 0.5 N/mm² and 30° (B) 0.05 N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°

Last Answer : Answer: Option B

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

The permissible diagonal tensile stress in reinforced brick work is (A) About 0.1 N/mm² (B) Zero (C) 0.3 N/mm² to 0.7 N/mm² (D) About 1.0 N/m2

Description : The permissible diagonal tensile stress in reinforced brick work is (A) About 0.1 N/mm² (B) Zero (C) 0.3 N/mm² to 0.7 N/mm² (D) About 1.0 N/m2

Last Answer : Answer: Option A

If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also

Last Answer : Answer: Option B

If the water table rises upto ground surface, then the (A) Effective stress is reduced due to decrease in total stress only but pore water pressure does not change (B) Effective stress is reduced due to increase in pore water pressure only but total stress does not change (C) Total stress is reduced due to increase in pore water pressure only but effective stress does not change (D) Total stress is increased due to decrease in pore water pressure but effective stress does not change

Description : If the water table rises upto ground surface, then the (A) Effective stress is reduced due to decrease in total stress only but pore water pressure does not change (B) Effective stress is ... D) Total stress is increased due to decrease in pore water pressure but effective stress does not change

Last Answer : (B) Effective stress is reduced due to increase in pore water pressure only but total stress does not change

direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure developed during the test (C) As the test progresses the area under shear, gradually changes (D) None of these

Description : direct shear test possesses the following disadvantage: (A) A relatively thin thickness of sample permits quick drainage (B) A relatively thin thickness of sample permits quick dissipation of pore pressure ... C) As the test progresses the area under shear, gradually changes (D) None of these

Last Answer : Answer: Option C

A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the leaves are 100mm and 12mm respectively. If modulus of elasticity is 207000N/mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm

Last Answer : b) 24.9mm

The length/diameter ratio of cylindrical specimens used in triaxial test, is generally (A) 1 (B) 1.5 (C) 2 (D) 2.5

Description : The length/diameter ratio of cylindrical specimens used in triaxial test, is generally (A) 1 (B) 1.5 (C) 2 (D) 2.5

Last Answer : Answer: Option C

Consider the following statements: 1. For a saturated soil, Skempton’s B-parameter is nearly equal to unity. 2. For an undisturbed sensitive clay, the stress-strain curve shows a peak. 3. Interlocking contributes significantly to the shearing strength in case of dense sand. Which of these statements are correct? (a) 1, 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Description : Consider the following statements: 1. For a saturated soil, Skempton's B-parameter is nearly equal to unity. 2. For an undisturbed sensitive clay, the stress-strain curve shows a peak. 3. Interlocking contributes significantly to the shearing ... 2 & 3 (b) 1 & 2 only (c) 2 & 3 only (d) 1 & 3 only

Last Answer : (a) 1, 2 & 3

In the triaxial compression test, the application of additional axial stress (i.e. deviator stress) on the soil specimen produces shear stress on (A) Horizontal plane only (B) Vertical plane only (C) Both horizontal and vertical planes (D) All planes except horizontal and vertical planes

Description : In the triaxial compression test, the application of additional axial stress (i.e. deviator stress) on the soil specimen produces shear stress on (A) Horizontal plane only (B) Vertical plane only (C) Both horizontal and vertical planes (D) All planes except horizontal and vertical planes

Last Answer : (D) All planes except horizontal and vertical planes

The triaxial apparatus is usually used for (A) Unconsolidated-undrained test (B) Consolidated-undrained test (C) Drained test (D) All the above tests

Description : The triaxial apparatus is usually used for (A) Unconsolidated-undrained test (B) Consolidated-undrained test (C) Drained test (D) All the above tests

Last Answer : Answer: Option D

For testing a saturated clay for shear strength, the test recommended, is (A) Direct shear test (B) Triaxial compression test (C) Unconfined compression test (D) All the above

Description : For testing a saturated clay for shear strength, the test recommended, is (A) Direct shear test (B) Triaxial compression test (C) Unconfined compression test (D) All the above

Last Answer : Answer: Option C

Select the incorrect statement. (A) In a direct shear box test, the plane of shear failure is predetermined (B) Better control is achieved on the drainage of the soil in a triaxial compression test (C) Stress distribution on the failure plane in the case of triaxial compression test is uniform (D) Unconfined compression test can be carried out on all types of soils

Description : Select the incorrect statement. (A) In a direct shear box test, the plane of shear failure is predetermined (B) Better control is achieved on the drainage of the soil in a triaxial compression ... compression test is uniform (D) Unconfined compression test can be carried out on all types of soils

Last Answer : Answer: Option D

For the determination of shear strength parameters, c and , of soil in the laboratory, the test to be conducted will be (a) Triaxial compression test (b) Sieve analysis (c) Compaction test (d) Relative density test

Description : For the determination of shear strength parameters, c and , of soil in the laboratory, the test to be conducted will be (a) Triaxial compression test (b) Sieve analysis (c) Compaction test (d) Relative density test

Last Answer : (a) Triaxial compression test

Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2

Description : Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2

Last Answer : Answer: Option C

The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm2

Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm

Last Answer : Answer: Option C

While swimming a depth of 13m in a fresh water lake a fish emits an air bubble of volume 2 mm² atmospheric pressure is 100kpa what is the original pressure of the bubble.  a. 217.17 kpa  b. 119 kpa  c. 326.15 kpa  d. 210 kap Pabs = Pg + Patm

Description : While swimming a depth of 13m in a fresh water lake a fish emits an air bubble of volume 2 mm² atmospheric pressure is 100kpa what is the original pressure of the bubble.  a. 217.17 kpa  b. 119 kpa  c. 326.15 kpa  d. 210 kap Pabs = Pg + Patm

Last Answer : 217.17 kpa

Pick up the correct statement from the following: (A) Isotropic consolidation of clay can be obtained in the triaxial apparatus under equal all￾round pressure (B) If the present effective stress is the maximum to which the clay has ever been subjected, it is called normally consolidated clay (C) If the present effective stress in the past was more than present effective stress, it is called over-consolidated clay (D) All the above

Description : Pick up the correct statement from the following: (A) Isotropic consolidation of clay can be obtained in the triaxial apparatus under equal all￾round pressure (B) If the present effective stress is the ... more than present effective stress, it is called over-consolidated clay (D) All the above

Last Answer : Answer: Option D

The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Description : The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Last Answer : Answer: Option C

Bulk diffusion in catalyst pore __________ with increase in pressure. (A) Increases (B) Decreases (C) Remains unchanged (D) Increases exponentially

Description : Bulk diffusion in catalyst pore __________ with increase in pressure. (A) Increases (B) Decreases (C) Remains unchanged (D) Increases exponentially

Last Answer : (B) Decreases

AA saturated clay is to be tested for shearing strength. Which test should be recommended? a) Direct shear test b) Triaxial shear test c) Vane shear test d) Unconfined compression*

Description : A saturated clay is to be tested for shearing strength. Which test should be recommended? a) Direct shear test b) Triaxial shear test c) Vane shear test d) Unconfined compression*

Last Answer : d) Unconfined compression*

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm

Last Answer : c) 8mm

A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm

Last Answer : a) 540mm

If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Description : If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²

Last Answer : a) 72 N/mm²

The slope of isochrone at any point at a given time indicates the rate of change of(A) Effective stress with time (B) Effective stress with depth (C) Pore water pressure with depth (D) Pore water pressure with time

Description : The slope of isochrone at any point at a given time indicates the rate of change of (A) Effective stress with time (B) Effective stress with depth (C) Pore water pressure with depth (D) Pore water pressure with time

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) The smaller the size of the pores, the higher the water can rise above the water table (B) Below the water table, the pore water may be static (C) The hydrostatic pressure depends on the depth below the water level (D) None of these

Description : Pick up the incorrect statement from the following: (A) The smaller the size of the pores, the higher the water can rise above the water table (B) Below the water table, the pore water may be static (C) The hydrostatic pressure depends on the depth below the water level (D) None of these

Last Answer : Answer: Option D

The pressure that builds up in pore water due to load increment on the soil, is termed (A) Excess pore pressure (B) Excess hydrostatic pressure (C) Hydrodynamic pressure (D) All the above

Description : The pressure that builds up in pore water due to load increment on the soil, is termed (A) Excess pore pressure (B) Excess hydrostatic pressure (C) Hydrodynamic pressure (D) All the above

Last Answer : Answer: Option D

Rise of water table above the ground surface causes (A) Equal increase in pore water pressure and total stress (B) Equal decrease in pore water pressure and total stress (C) Increase in pore water pressure but decrease in total stress (D) Decrease in pore water pressure but increase in total stress

Description : Rise of water table above the ground surface causes (A) Equal increase in pore water pressure and total stress (B) Equal decrease in pore water pressure and total stress (C) Increase in ... pressure but decrease in total stress (D) Decrease in pore water pressure but increase in total stress

Last Answer : Answer: Option A

The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame’s equation. Diameter of the cylinder is 40mm and pressure in cylinder is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed

Last Answer : c) 5.07mm

07. A closed tank is completely filled with an oil. If it is made to move with a horizontal acceleration, then the pressure at the back end will be more than that at the front end. A) Correct B) Incorrect

Description : 07. A closed tank is completely filled with an oil. If it is made to move with a horizontal acceleration, then the pressure at the back end will be more than that at the front end. A) Correct B) Incorrect

Last Answer : A

During consolidation process of clayey soils, indicate the sequence of occurrence of the following events in the order from first to last : 1. Load being taken up by the pore water 2. Load being taken up by the soil grains 3. Drainage of water from the pores of the soil (a) 1, 2 and 3 (b) 2, 3 and 1 (c) 1, 3 and 2 (d) 2, 1 and 3

Description : During consolidation process of clayey soils, indicate the sequence of occurrence of the following events in the order from first to last : 1. Load being taken up by the pore water 2. Load being taken up by the soil grains 3. Drainage of ... 1, 2 and 3 (b) 2, 3 and 1 (c) 1, 3 and 2 (d) 2, 1 and 3

Last Answer : (c) 1, 3 and 2

The importance of diffusion in a catalyst are increased by (A) Large catalyst particle size (B) An active surface of the catalyst (C) Small pore diameter (D) All (A), (B) and (C)

Description : The importance of diffusion in a catalyst are increased by (A) Large catalyst particle size (B) An active surface of the catalyst (C) Small pore diameter (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm

Last Answer : b) 41.2mm

What will be the values of x, m and n after execution of the following statements? Int x, m, n; m=10; n=15; x= ++m + n++; A) x=25, m=10, n=15 B) x=27, m=10, n=15 C) x=26, m=11, n=16 D) x=27, m=11, n=16

Description : What will be the values of x, m and n after execution of the following statements? Int x, m, n; m=10; n=15; x= ++m + n++; A) x=25, m=10, n=15 B) x=27, m=10, n=15 C) x=26, m=11, n=16 D) x=27, m=11, n=16

Last Answer : C) x=26, m=11, n=16

Pick out the wrong statement. (A) Exit age description function (E) and internal age distribution function (I) are related as, E = -(dI/dθ) (B) Chemisorption studies are useful in the determination of catalyst surface area and pore size distribution (C) A higher temperature favours the reaction of higher activation energy (D) A catalyst increases the potential energy barrier over which the reactants must pass to form products

Description : Pick out the wrong statement. (A) Exit age description function (E) and internal age distribution function (I) are related as, E = -(dI/dθ) (B) Chemisorption studies are useful in the ... energy (D) A catalyst increases the potential energy barrier over which the reactants must pass to form products

Last Answer : (D) A catalyst increases the potential energy barrier over which the reactants must pass to form products

The number of revolutions through which a pulley will rotate from rest if its angular acceleration is increased uniformly from zero to 12 rad per sec2 during 4 sec and then uniformly decreased to 0 rad per sec2 during the next 3 sec would be a.46.4 b.26.74 c.11.6 d.3.2 e.17.7

Description : The number of revolutions through which a pulley will rotate from rest if its angular acceleration is increased uniformly from zero to 12 rad per sec2 during 4 sec and then uniformly decreased to 0 rad per sec2 during the next 3 sec would be a.46.4 b.26.74 c.11.6 d.3.2 e.17.7

Last Answer : b. 26.74

Is 5.15 5.07?

Description : Is 5.15 5.07?

Last Answer : 5.15 is greater than 5.07

Using the data in question 7, calculate the 95% confidence interval for the mean ACT score based on the t-distribution. a. -∞ to 23.05 b. -∞ to 23.15 c. 18.07 to 23.63 d. 18.22 to 23.48

Description : Using the data in question 7, calculate the 95% confidence interval for the mean ACT score based on the t-distribution. a. -∞ to 23.05 b. -∞ to 23.15 c. 18.07 to 23.63 d. 18.22 to 23.48

Last Answer : c. 18.07 to 23.63

The compression resulting from a long term static load and consequent escape of pore water, is known as (A) Compaction (B) Consolidation (C) Swelling (D) None of these

Description : The compression resulting from a long term static load and consequent escape of pore water, is known as (A) Compaction (B) Consolidation (C) Swelling (D) None of these

Last Answer : (B) Consolidation

Terzaghi's theory of one dimensional consolidation assumes (A) Load is applied in one direction (B) Coefficient of permeability is constant (C) Excess pore water drains out only in the vertical direction (D) All the above

Description : Terzaghi's theory of one dimensional consolidation assumes (A) Load is applied in one direction (B) Coefficient of permeability is constant (C) Excess pore water drains out only in the vertical direction (D) All the above

Last Answer : Answer: Option D

The neutral stress in a soil mass is (A) Force per neutral area (B) Force per effective area (C) Stress taken up by the pore water (D) Stress taken up by solid particles

Description : The neutral stress in a soil mass is (A) Force per neutral area (B) Force per effective area (C) Stress taken up by the pore water (D) Stress taken up by solid particles

Last Answer : Answer: Option C

In multistage equilibrium conversion of SO2 to SO3 (2SO2 + O2 ⇌ 2SO3 ), the reverse reaction becomes appreciable at a temperature of 550° C. The percentage equilibrium conversion of SO2 to SO3 can be increased by (A) Increasing the oxygen concentration (B) Putting more quantity of V2O5 catalyst in the converter (C) Removing some quantity of SO3 during intermediate stage (D) Maintaining low temperature & pressure in the converter

Description : In multistage equilibrium conversion of SO2 to SO3 (2SO2 + O2 ⇌ 2SO3 ), the reverse reaction becomes appreciable at a temperature of 550° C. The percentage equilibrium conversion of SO2 to ... some quantity of SO3 during intermediate stage (D) Maintaining low temperature & pressure in the converter

Last Answer : (C) Removing some quantity of SO3 during intermediate stage