Description : The permissible diagonal tensile stress in reinforced brick work is (A) About 0.1 N/mm² (B) Zero (C) 0.3 N/mm² to 0.7 N/mm² (D) About 1.0 N/m2
Last Answer : Answer: Option A
Description : Pick up the correct statement from the following: (A) The average crushing strength of hand moulded bricks is 6000 t/m2 (B) The average tensile strength of hand moulded brick is 200 t/m2 (C) The average shearing strength of hand moulded brick is 600 t/m2 (D) All the above
Last Answer : Answer: Option D
Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm
Last Answer : Answer: Option C
Description : During the first stage of triaxial test when the cell pressure is increased from 0.10 N/mm² to 0.26 N/mm², the pore water pressure increases from 0.07 N/mm² to 0.15 N/mm². Skempton's pore B (A) 0.5 (B) -0.5 (C) 2.0 (D) -2.0
Last Answer : (A) 0.5
Description : If yielding strength=400N/mm², the find the permissible shear stress according to ASME standards. a) 72 N/mm² b) 76 N/mm² c) 268 N/mm² d) 422 N/mm²
Last Answer : a) 72 N/mm²
Description : Minimum number of 50 kg cement bags per cubic metre of concrete for a mix corresponding to crushing strength 280 kg/cm2 at 28 days, are (A) 5.0 (B) 6.5 (C) 7.0 (D) 7.5
Last Answer : Answer: Option B
Description : A cylindrical specimen of saturated soil failed under an axial vertical stress of 100kN/m² when it was laterally unconfmed. The failure plane was inclined to the horizontal plane at an angle of 45°. The values of cohesion and angle of ... N/mm² and 0° (C) 0.2 N/mm² and 0° (D) 0.05 N/mm² and 45°
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : A 300 mm square bearing plate settles by 15 mm in a plate load test on a cohesive soil when the intensity of loading is 0.2 N/mm². The settlement of a prototype shallow footing 1 m square under the same intensity of loading is (A) 15 mm (B) 30 mm (C) 50 mm (D) 167 mm
Last Answer : (C) 50 mm
Description : If the permissible stress in steel in tension is 140 N/mm², then the depth of neutral axis for a singly reinforced rectangular balanced section will be (A) 0.35 d (B) 0.40 d (C) 0.45 d (D) Dependent on grade of concrete also
Description : Granite is not suitable for ordinary building purpose because (A) It cannot be polished (B) It is not a fire proof material (C) It is costly (D) It has less crushing strength
Description : Modulus of elasticity of steel as per IS: 4561978 shall be taken as (A) 20 kN/cm² (B) 200 kN/cm² (C) 200 kN/mm² (D) 2 × 106 N/cm2
Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the thickness of the cylinder if it is twice the diameter of the cylinder. a) 12mm b) 4mm c) 8mm d) 16mm
Last Answer : c) 8mm
Description : A seamless cylinder of storage capacity of 0.03mᵌis subjected to an internal pressure of 21MPa. The ultimate strength of material of cylinder is 350N/mm².Determine the length of the cylinder if it is twice the diameter of the cylinder. a) 540mm b) 270mm c) 400mm d) 350mm
Last Answer : a) 540mm
Description : The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2
Last Answer : : Option B
Description : A leaf spring consists of 3 extra full length leaves and 14 graduated length leaves. The maximum force that can act on the spring is 70kN and the distance between eyes of the spring is 1.2m. Width and thickness of the ... /mm², calculate the initial nip. (a) 26.8mm (b) 24.9mm (c) 22.5mm (d)23.1mm
Last Answer : b) 24.9mm
Description : Crushing strength of a good building stone should be more than (A) 50 MPa (B) 100 MPa (C) 150 MPa (D) 200 MPa
Description : In favourable circumstances a 15 cm concrete cube after 28 days, attains a maximum crushing strength (A) 100 kg/cm2 (B) 200 kg/cm2 (C) 300 kg/cm2 (D) 400 kg/cm
Description : Which of the following tests measures the toughness of road aggregates? (A) Crushing strength test (B) Abrasion test (C) Impact test (D) Shape test
Description : Los Angeles testing machine is used to conduct (A) Abrasion test (B) Impact test (C) Attrition test (D) Crushing strength test
Description : Log Angles machine is used to test the aggregate for (A) Crushing strength (B) Impact value (C) Abrasion resistance (D) Water absorption
Description : Pick up the correct statement from the following: (A) Acid test is done to find out the weathering quality of stones (B) Attrition test is done to find out the rate of wear of stones which are used ... (C) Crushing test is done to find out the compressive strength of the stone (D) All the above
Description : The stone whose crushing strength is least, is (A) Granite (B) Chalk (C) Marble (D) Slate
Description : The stone whose crushing strength is maximum, is (A) Granite (B) Chalk (C) Slate (D) Sand stone
Description : Los Angles machine is used to perform (a) Crushing strength (b) Impact test (c) Water absorption (d) Abrasion resistance test
Last Answer : (d) Abrasion resistance test
Description : Generally the strength of concrete is represented by the crushing stress of concrete cube of size [ A ] 50 mm [ B ] 100 mm [ C ] 150 mm [ D ] 250 mm
Last Answer : [ C ] 150 mm
Description : Austenitic manganese steel used for making jaws of crushing machines contains about __________ percent manganese. (A) 1.5-2 (B) 3.5-4.5 (C) 7-9 (D) 12-14
Last Answer : (D) 12-14
Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5
Last Answer : (B) 0.1
Description : The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2
Last Answer : (b) 17.5 N/mm2
Description : he minimum compressive strength of first class brick should be a) 75 kg per centimeter square b) 90 kg per centimeter square c) 100 kg per centimeter square* d) 120 kg per centimeter square
Last Answer : c) 100 kg per centimeter square*
Description : A 1st class brick immersed in water for 24 hours, should not absorb water (by weight) more than (A) 10 % (B) 15 % (C) 20 % (D) 25 %
Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4
Last Answer : a) 7
Description : The strength of brick masonry in 1:6 cement mortar, is (A) 20 tonnes/m2 (B) 40 tonnes/m2 (C) 50 tonnes/m2 (D) 60 tonnes/m
Description : A first class brick when immersed in cold water for 24 hours should not absorb water more than (A) 15 % (B) 20 % (C) 22 % (D) 25 %
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm². a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : Rittinger number which designates the new surface produced per unit of mechanical energy absorbed by the material being crushed, depends on the (A) State or manner of application of the crushing force (B) Ultimate strength of the material (C) Elastic constant of the material (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Strength of a rivet is a. Strength in shear b. Strength in crushing c. Strength in tension d. None
Last Answer : d. None
Description : To obtain good bonding in brick masonry (A) First class bricks are used (B) Vertical joints in alternate courses are kept in plumb line (C) Bats are used where necessary (D) All the above
Last Answer : Option D
Description : The type of arch used for high class buildings where appearance is of prime importance, is known as (A) Ashlar arch (B) Rubble arch (C) Gauged brick arch (D) Axed brick arch
Description : Newly constructed pavement with ordinary Portland cement attains its working strength after (A) 7 days (B) 14 days (C) 21 days (D) 28 days
Description : How long will it take for the concrete to achieve 100% of its strength? (A) 7 days (B) 14 days (C) 21 days (D) 28 day
Description : General crushing equation is given by d(P/m) = -K (dD̅S /D̅ n S ). Bond's crushing law is obtained by solving this equation for n = __________ and feed of infinite size. (A) 1 (B) 1.5 (C) 2 (D) 2.5
Last Answer : (B) 1.5
Description : The piston rod of a hydraulic cylinder exerts an operating force of 10kN. The allowable stress in the cylinder is 45N/mm². Calculate the thickness of the cylinder using Lame's equation. Diameter of the cylinder is 40mm and ... is 10MPa. a) 2.05mm b) 4.2mm c) 5.07mm d) None of the listed
Last Answer : c) 5.07mm
Description : Theoretical capacity of crushing rolls in tons/hr is given by (where, V = peripheral velocity, m/sec. W = width of rolls, m Dr = distance between rolls ρ = density of material to be crushed, kg/m3 here, V =πND where, N = speed of the rolls ... V.W.Dr.ρ (B) 3.6 V.W. ρ (C) 3.6 W.Dr.ρ (D) 3.6 V.W.Dr/ρ
Last Answer : (A) 3.6 V.W.Dr.ρ
Description : While swimming a depth of 13m in a fresh water lake a fish emits an air bubble of volume 2 mm² atmospheric pressure is 100kpa what is the original pressure of the bubble. a. 217.17 kpa b. 119 kpa c. 326.15 kpa d. 210 kap Pabs = Pg + Patm
Last Answer : 217.17 kpa
Description : Find the shear stress in the spring wire used to design a helical compression sprig if a load of 1200N is applied on the spring. Spring index is 6, and wire diameter 7mm. a) 452.2N/mm² b) 468.6N/mm² c) 512.2N/mm² d) None of the listed
Last Answer : b) 468.6N/mm²
Description : According to IS specifications, the compressive strength of ordinary Portland cement after three days should not be less than (A) 7 MPa (B) 11.5 MPa (C) 16 MPa (D) 21 MPa
Description : The nominal thickness of an expansion joint in brick walls, is kept more than (A) 5 mm (B) 10 mm (C) 15 mm (D) 20 mm
Description : When does machop learn strength in Pokemon brick bronze?
Last Answer : Need answer
Description : Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers ( ... (D) States that the work required for the crushing is proportional to the new surface created
Last Answer : (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law