If the reduced bearing of a line AB is N60°W and length is 100 m, then the latitude and departure respectively of the line AB will be (A) +50 m, +86.6 m (B) +86.6 m, -50 m (C) +50 m, -86.6 m (D) +70.7 m, -50 m

If the reduced bearing of a line AB is N60°W and length is 100 m, then the latitude and departure
respectively of the line AB will be
(A) +50 m, +86.6 m
(B) +86.6 m, -50 m
(C) +50 m, -86.6 m
(D) +70.7 m, -50 m
by

1 Answer

Answer :

(B) +86.6 m, -50 m
by

Related questions

The orthographical projection of a traverse leg upon the reference meridian, is known as (A) Departure of leg (B) Latitude to the leg (C) Co-ordinate of the leg (D) Bearing of the leg

Description : The orthographical projection of a traverse leg upon the reference meridian, is known as (A) Departure of leg (B) Latitude to the leg (C) Co-ordinate of the leg (D) Bearing of the leg

Last Answer : (B) Latitude to the leg

The length of a traverse leg may be obtained by multiplying the latitude and (A) Secant of its reduced bearing (B) Sine of its reduced bearing (C) Cosine of its reduced bearing (D) Tangent of its reduced bearing

Description : The length of a traverse leg may be obtained by multiplying the latitude and (A) Secant of its reduced bearing (B) Sine of its reduced bearing (C) Cosine of its reduced bearing (D) Tangent of its reduced bearing

Last Answer : (A) Secant of its reduced bearing

The bearing of C from A is N 30° E and from B, 50 metres east of A, is N 60° W. The departure of C from A is (A) 50 m (B) 50 m (C) 25 m (D) 25 m

Description : The bearing of C from A is N 30° E and from B, 50 metres east of A, is N 60° W. The departure of C from A is (A) 50 m (B) 50 m (C) 25 m (D) 25 m

Last Answer : (D) 25 m

A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m and 284.295 m respectively, the collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m

Description : A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m ... collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m

Last Answer : (D) 0.060 m

The co-ordinate of a point measured perpendicular to the parallel, is called (A) Total latitude (B) Meridian distance (C) Total departure (D) Consecutive co-ordinate

Description : The co-ordinate of a point measured perpendicular to the parallel, is called (A) Total latitude (B) Meridian distance (C) Total departure (D) Consecutive co-ordinate

Last Answer : (A) Total latitude

D and E are respectively the points on the sides AB and AC of a triangle ABC such that AD = 2 cm, BD = 3 cm, BC = 7.5 cm and DE || BC. Then, length of DE (in cm) is (a) 2.5 (b) 3 (c) 5 (d) 6

Description : D and E are respectively the points on the sides AB and AC of a triangle ABC such that AD = 2 cm, BD = 3 cm, BC = 7.5 cm and DE || BC. Then, length of DE (in cm) is (a) 2.5 (b) 3 (c) 5 (d) 6

Last Answer : (b) 3

The reduced levels of the string at the consecutive sight rails A and B are 203.575 m, 203.475 m respectively. If the difference of their R.D.s is 10 m, the gradient of the sewer line is A. 1 in 100 upward B. 1 in 500 upward C. 1 in 100 downward D. 1 in 503 upward

Description : The reduced levels of the string at the consecutive sight rails A and B are 203.575 m, 203.475 m respectively. If the difference of their R.D.s is 10 m, the gradient of the sewer line is A. 1 in 100 upward B. 1 in 500 upward C. 1 in 100 downward D. 1 in 503 upward

Last Answer : ANS: C

Define Latitude and Departure.

Description : Define Latitude and Departure. 

Last Answer : Latitude : The projection of survey line parallel to meridian is called latitude. OR Projection of survey line parallel to N-S direction is called latitude. Departure: The projection of survey ... is called departure. OR Projection of survey line parallel to E-W direction is called departure.

Define the term departure and latitude

Description : Define the term departure and latitude

Last Answer : Departure :- It is the distance parallel to the East-West line OR the projection of survey line perpendicular to the meridian is called departure. Latitude :- It is the distance parallel to the North-South line OR the projection of survey line parallel to the meridian is called latitude.

Define the terms- latitude and departure.

Description : Define the terms- latitude and departure. 

Last Answer :  Latitude – The projective distance of survey line parallel to meridian (i.e. N-S direction) is known as Latitude of a line. Departure - The projective distance of survey line perpendicular to meridian (i.e. N-S direction) is known as Departure of a line.

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in temperature causes a tape to increase in length and the measured distance is too large (C) The straight distance between end points of a suspended tape is reduced by an amount called the sag correction (D) A 100 m tape of cross section 10 mm × 0.25 mm stretches about 10 mm under 5 kg pull

Description : Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in ... ) A 100 m tape of cross section 10 mm 0.25 mm stretches about 10 mm under 5 kg pull

Last Answer : (B) An increase in temperature causes a tape to increase in length and the measured distance is too large

A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. The outside diameter (in mm) of the shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100

Last Answer : (a) 43 to 45

The bearing of line AB is 152° 30' and angle ABC measured clockwise is 124° 28'. The bearing of BC is (A) 27° 52' (B) 96° 58' (C) 148° 08' (D) 186° 58'

Description : The bearing of line AB is 152° 30' and angle ABC measured clockwise is 124° 28'. The bearing of BC is (A) 27° 52' (B) 96° 58' (C) 148° 08' (D) 186° 58'

Last Answer : (B) 96° 58'

ABCD is a regular parallelogram plot of land whose angle BAD is 60°. If the bearing of the line AB is 30°, the bearing of CD, is (A) 90° (B) 120° (C) 210° (D) 270°

Description : ABCD is a regular parallelogram plot of land whose angle BAD is 60°. If the bearing of the line AB is 30°, the bearing of CD, is (A) 90° (B) 120° (C) 210° (D) 270°

Last Answer : (C) 210°

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface between B and C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50

Last Answer : (C) 70

If h and h1 are the heights of a light house and the observer in a ship in metres above M S L then the horizontal distance from the ship to the light house in kilometres is (A) h + h1) (B) h - h1) (C) h × h1) (D) 3.86 h + h1)

Description : If h and h1 are the heights of a light house and the observer in a ship in metres above M S L then the horizontal distance from the ship to the light house in kilometres is (A) h + h1) (B) h - h1) (C) h × h1) (D) 3.86 h + h1)

Last Answer : (A) h + h1)

The whole circle bearing of a line is 290°. Its reduced bearing is (A) N 20° E (B) N 20° W (C) N 70° W (D) S 70° E

Description : The whole circle bearing of a line is 290°. Its reduced bearing is  (A) N 20° E (B) N 20° W (C) N 70° W (D) S 70° E

Last Answer : (C) N 70° W

If whole circle bearing of a line is 120°, its reduced bearing is (A) S 20° E (B) S 60° E (C) N 120° E (D) N 60° E

Description : If whole circle bearing of a line is 120°, its reduced bearing is  (A) S 20° E (B) S 60° E (C) N 120° E (D) N 60° E

Last Answer : (B) S 60° E

A bearing of a line is also known as (A) Magnetic bearing (B) True bearing (C) Azimuth (D) Reduced bearing

Description : A bearing of a line is also known as  (A) Magnetic bearing  (B) True bearing  (C) Azimuth  (D) Reduced bearing 

Last Answer : (B) True bearing

If the whole circle bearing of a line is 180°, its reduced bearing is (A) S 0° E (B) S 0° W (C) S (D) N

Description : If the whole circle bearing of a line is 180°, its reduced bearing is (A) S 0° E (B) S 0° W (C) S (D) N

Last Answer : (C) S

The reduced bearing of a line is N 87° W. Its whole circle bearing is (A) 87° (B) 273° (C) 93° (D) 3°

Description : The reduced bearing of a line is N 87° W. Its whole circle bearing is (A) 87° (B) 273° (C) 93° (D) 3°

Last Answer : (B) 273°

Reduced bearing of a line is an angle between (A) North line and given line measured clockwise (B) North line and given line measured anticlockwise (C) East or west and the given line (D) Given line and the part of the meridian whether N end or S end, lying adjacent to it

Description : Reduced bearing of a line is an angle between (A) North line and given line measured clockwise (B) North line and given line measured anticlockwise (C) East or west and the given line (D) Given line and the part of the meridian whether N end or S end, lying adjacent to it

Last Answer : (D) Given line and the part of the meridian whether N end or S end, lying adjacent to it

If the whole circle bearing of a line is 270°, its reduced bearing is (A) N 90° W (B) S 90° W (C) W 90° (D) 90° W

Description : If the whole circle bearing of a line is 270°, its reduced bearing is (A) N 90° W (B) S 90° W (C) W 90° (D) 90° W

Last Answer : (C) W 90°

If the rate of change of the super-elevation along a curved portion of a 7 metre wide road is 1 in 150 and the maximum super-elevation allowed is 1 in 15, the maximum length of the transition curve to be provided at either end, is (A) 65 m (B) 70 m (C) 75 m (D) 80 m

Description : If the rate of change of the super-elevation along a curved portion of a 7 metre wide road is 1 in 150 and the maximum super-elevation allowed is 1 in 15, the maximum length of the transition curve to be provided at either end, is (A) 65 m (B) 70 m (C) 75 m (D) 80 m

Last Answer : Answer: Option B

Draw a line segment AB of 4 cm in length. Draw a line perpendicular to AB through A and B, respectively. -Maths 9th

Description : Draw a line segment AB of 4 cm in length. Draw a line perpendicular to AB through A and B, respectively. -Maths 9th

Last Answer : The lines are perpendicular to a common line AB. Hence, the angle between these lines will be 90+90=180∘ Since, the angle between them is 180∘, the lines are parallel to each other.

Draw a line segment AB of 4 cm in length. Draw a line perpendicular to AB through A and B, respectively. -Maths 9th

Description : Draw a line segment AB of 4 cm in length. Draw a line perpendicular to AB through A and B, respectively. -Maths 9th

Last Answer : To draw a line perpendicular to AB through A and B, respectively. Use the following steps of construction. 1.Draw a line segment AB = 4 cm. 2.Taking 4 as centre and radius more than ½ AB (i.e ... [since, it sum of interior angle on same side of transversal is 180°, then the two lines are parallel]

For testing compressive strength of cement, the size of cube used is (A) 50 mm (B) 70.6 mm (C) 100 mm (D) 150 mm

Description : For testing compressive strength of cement, the size of cube used is (A) 50 mm (B) 70.6 mm (C) 100 mm (D) 150 mm

Last Answer : B

If is the perimete D is the closing error in departure, the correction for the departure of a traverse side of length , according to Bowditch rule, is (A) D × L/l (B) D × l²/L (C) L × l D (D) D × l/L

Description : If is the perimete D is the closing error in departure, the correction for the departure of a traverse side of length , according to Bowditch rule, is (A) D × L/l (B) D × l²/L (C) L × l D (D) D × l/L

Last Answer : (D) D × l/L

Due to a rise in temperature, the viscosity and the unit weight of the percolating fluid are reduced to 60% and 90% respectively. If other things remain constant, the coefficient of permeability (A) Increases by 25 % (B) Increases by 50 % (C) Increases by 33.3 % (D) Decreases by 33.3 %

Description : Due to a rise in temperature, the viscosity and the unit weight of the percolating fluid are reduced to 60% and 90% respectively. If other things remain constant, the coefficient of permeability (A) Increases by 25 % (B) Increases by 50 % (C) Increases by 33.3 % (D) Decreases by 33.3 %

Last Answer : (B) Increases by 50 %

A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural frequency (f n ), respectively, are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz

Description : A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural ... , are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz

Last Answer : a) 0.471 and 1.19 Hz

A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural frequency (f n ), respectively, are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz d) 0.666 and 8.50 Hz

Description : A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural ... .19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz d) 0.666 and 8.50 Hz

Last Answer : a) 0.471 and 1.19 Hz

The length, breadth and height of a room are 5 m, 4 m and 3 m respectively. Find the cost of white washing the walls of the room and ceiling at the rate of Rs 7.50 per m2. -Maths 9th

Description : The length, breadth and height of a room are 5 m, 4 m and 3 m respectively. Find the cost of white washing the walls of the room and ceiling at the rate of Rs 7.50 per m2. -Maths 9th

Last Answer : Length (l) of room = 5m Breadth (b) of room = 4m Height (h) of room = 3m It can be observed that four walls and the ceiling of the room are to be white washed. Total area to be white washed = Area of walls + ... m2 area = Rs.7.50 (Given) Cost of white washing 74 m2 area = Rs. (74 7.50) = Rs. 555

Consider two alloys A and B. 50 kg of alloy A is mixed with 70 kg of alloy B. A contains brass and copper in the ratio 3 : 2, and B contains them in the ratio 4 : 3 respectively. What is the ratio of copper to brass in the mixture? A) 8 : 5 B) 7 : 5 C) 5 : 11 D) 4 : 9 E) 5 : 7

Description : Consider two alloys A and B. 50 kg of alloy A is mixed with 70 kg of alloy B. A contains brass and copper in the ratio 3 : 2, and B contains them in the ratio 4 : 3 respectively. What is the ratio of copper to brass in the mixture? A) 8 : 5 B) 7 : 5 C) 5 : 11 D) 4 : 9 E) 5 : 7

Last Answer : Answer: E Brass in A = 3/5 * 50 = 30 kg, Brass in B = 4/7 * 70 = 40 kg Total brass = 30+40 = 70 kg So copper in mixture is (50+70) – 70 = 50 kg So copper to brass = 50 : 70=5:7

The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

Pick up the incorrect statement from the following: (A) Space between the exterior walls of a warehouse and bag piles should be 30 cm (B) Cement bags should preferably be piled on wooden planks (C) Width and height of the pile should not exceed 3 m and 2.70 m respectively (D) None of these

Description : Pick up the incorrect statement from the following: (A) Space between the exterior walls of a warehouse and bag piles should be 30 cm (B) Cement bags should preferably be piled on wooden planks (C) Width and height of the pile should not exceed 3 m and 2.70 m respectively (D) None of these

Last Answer : Answer: Option D

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

For the MN-blood group system. The frequencies of M and N alleles are 0.7 and 0.3, respectively. The expected frequency of MN-blood group bearing orga

Description : For the MN-blood group system. The frequencies of M and N alleles are 0.7 and 0.3, respectively. The expected frequency of MN-blood group bearing orga

Last Answer : For the MN-blood group system. The frequencies of M and N alleles are 0.7 and 0.3, respectively. The expected ... `42%` B. `49%` C. `9%` D. `58%`

Consider a system having ‘m’ resources of the same type. These resources are shared by three processes P1, P2 and P3 which have peak demands of 2, 5 and 7 resources respectively. For what value of ‘m’ deadlock will not occur? (A) 70 (B) 14 (C) 13 (D) 7

Description : Consider a system having ‘m’ resources of the same type. These resources are shared by three processes P1, P2 and P3 which have peak demands of 2, 5 and 7 resources respectively. For what value of ‘m’ deadlock will not occur? (A) 70 (B) 14 (C) 13 (D) 7

Last Answer : (B) 14

In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm. The focussing lens is midway between them when a staff 16.50 m away is focussed. The focal length of the focussing lens, is (A) 5.24 cm (B) 6.24 cm (C) 7.24 cm (D) 8.24 cm

Description : In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm. The focussing lens is midway between them when a staff 16.50 m away is focussed. The focal length of the focussing lens, is (A) 5.24 cm (B) 6.24 cm (C) 7.24 cm (D) 8.24 cm

Last Answer : (C) 7.24 cm

Biological value of egg proteins is about (A) 70 % (B) 80 % (C) 86 % (D) 94 %

Description : Biological value of egg proteins is about (A) 70 % (B) 80 % (C) 86 % (D) 94 %

Last Answer : Answer : D

A man pulls a cart with 100 N force from rest with an acceleration of 10 m/sec2 for 10 seconds. The work done by him is a.500 KJ b.50.96 KJ c.101.92 KJ d.None of the above e.Tapered bearing

Description : A man pulls a cart with 100 N force from rest with an acceleration of 10 m/sec2 for 10 seconds. The work done by him is a.500 KJ b.50.96 KJ c.101.92 KJ d.None of the above e.Tapered bearing

Last Answer : a. 500 KJ

M.I. of sphere of 0.5 m radius about a mutually perpendicular axis (Z-axis) when its M.I. about X-axis and Y-axis are 50 kgm2 and 50 kgm2 is a.50 Kgm2 b.Tapered bearing c.100 Kgm2 d.25 Kgm2 e.12.5 Kgm2

Description : M.I. of sphere of 0.5 m radius about a mutually perpendicular axis (Z-axis) when its M.I. about X-axis and Y-axis are 50 kgm2 and 50 kgm2 is a.50 Kgm2 b.Tapered bearing c.100 Kgm2 d.25 Kgm2 e.12.5 Kgm2

Last Answer : a. 50 Kgm2

Minimum thickness of load bearing RCC wall should be (A) 50 mm (B) 100 mm (C) 150 mm (D) 200 mm

Description : Minimum thickness of load bearing RCC wall should be (A) 50 mm (B) 100 mm (C) 150 mm (D) 200 mm

Last Answer : (B) 100 mm

The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2

Description : The minimum strength of the mortar used in load bearing brick masonry, is (A) 50 N/cm2 (B) 100 N/cm2 (C) 150 N/cm2 (D) 200 N/cm2

Last Answer : : Option B

The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope of the arch). (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E

Description : The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with  a uniformly distributed load l t per horizontal length is (where Ic  is the M.I. at the crown, which  varies as the slope ... arch).  (A) 50/EIc (B) 100/EIc (C) 150/EIc (D) 200/E

Last Answer : (D) 200/E

A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff readings at and were 1.22 and 1.06. With the level set up at , the readings at and were 1.55 and 1.37. The collimation error per 100 m length of sight is (A) 0.02 m inclined upwards (B) 0.04 m inclined downwards (C) 0.04 m inclined upward (D) None of these

Description : A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff  readings at and were 1.22 and 1.06. With the level set up at , the readings at  and were 1.55 and ... upwards  (B) 0.04 m inclined downwards  (C) 0.04 m inclined upward  (D) None of these

Last Answer : (B) 0.04 m inclined downwards