The moment capacity of section at plastic hinge equals a) Yield moment b) Zero c) Fully plastic moment d) Twice the yield moment

The moment capacity of section at plastic hinge equals
a) Yield moment
b) Zero
c) Fully plastic moment
d) Twice the yield moment
by

1 Answer

Answer :

c) Fully plastic moment
by

Related questions

Pick up the correct statement from the following: (A) In a loaded beam, the moment at which the first yield occurs is called yield moment(B) In a loaded beam, the moment at which the entire section of the beam becomes fully plastic, is called plastic moment (C) In a fully plastic stage of the beam, the neutral axis divides the section in two sections of equal area (D) All the above

Description : Pick up the correct statement from the following:  (A) In a loaded beam, the moment at which the first yield occurs is called yield moment (B) In a loaded beam, the moment at which the ... beam, the neutral axis divides the section in two sections of  equal area  (D) All the above 

Last Answer : (D) All the above 

What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Description : What is the distance away from midspan of a plastic hinge if developing in a simply supported beam of rectangular cross-section and span 6 m, subjected to a point load at the centre? (a) Zero (b) 1 m (c) 2 m (d) 3 m

Last Answer : (a) Zero

Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Description : Which one of the following is the correct ratio of plastic moment to yield moment for a simply supported beam of uniform square cross section throughout the span (a) 1.5 (b) 1.7 (c) 2.0 (d) 2.34

Last Answer : (a) 1.5

In case of a simply supported I-section beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported I-section beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (D) L/5 

At fully plastic twisting moment (a) only fibres at surface are stressed to yield point in shear (b) fibres at centre are stressed to yield point in shear (c) all fibres are stressed to yield point in shear (d) none of these

Description : At fully plastic twisting moment (a) only fibres at surface are stressed to yield point in shear (b) fibres at centre are stressed to yield point in shear (c) all fibres are stressed to yield point in shear (d) none of these

Last Answer : (c) all fibres are stressed to yield point in shear

In a three hinged arch, the bending moment will be zero (A) At right hinge only (B) At left hinge only (C) At both right and left hinges (D) At all the three hinges

Description : In a three hinged arch, the bending moment will be zero (A) At right hinge only (B) At left hinge only (C) At both right and left hinges (D) At all the three hinges

Last Answer : (D) At all the three hinges

Which of the following conditions is to be satisfied both in elastic and plastic analyses? (a) Equilibrium condition (b) Yield condition (c ) Plastic moment condition (d) Mechanism condition

Description : Which of the following conditions is to be satisfied both in elastic and plastic analyses? (a) Equilibrium condition (b) Yield condition (c ) Plastic moment condition (d) Mechanism condition

Last Answer : (a) Equilibrium condition

In case of a simply supported rectangular beam of span L and loaded with a central load W, the length of elasto-plastic zone of the plastic hinge, is (A) L/2 (B) L/3 (C) L/4 (D) L/5

Description : In case of a simply supported rectangular beam of span L and loaded with a central load W, the  length of elasto-plastic zone of the plastic hinge, is  (A) L/2  (B) L/3  (C) L/4  (D) L/5 

Last Answer : (B) L/3 

In a continuous bending moment curve the point where it changes sign, is called (A) Point of inflexion (B) Point of contraflexure (C) Point of virtual hinge (D) All the above

Description : In a continuous bending moment curve the point where it changes sign, is called (A) Point of inflexion (B) Point of contraflexure (C) Point of virtual hinge (D) All the above

Last Answer : (D) All the above

The yield moment of a cross section is defined as the moment that will just produce the yield stress in (A) The outer most fibre of the section (B) The inner most fibre of the section (C) The neutral fibre of the section (D) The fibre everywhere

Description : The yield moment of a cross section is defined as the moment that will just produce the yield  stress in  (A) The outer most fibre of the section  (B) The inner most fibre of the section  (C) The neutral fibre of the section  (D) The fibre everywhere 

Last Answer : (A) The outer most fibre of the section 

Effects of shear force and axial force on plastic moment capacity of a structure are respectively to (A) Increase and decrease (B) Increase and increase (C) Decrease and increase (D) Decrease and decrease

Description : Effects of shear force and axial force on plastic moment capacity of a structure are respectively to (A) Increase and decrease (B) Increase and increase (C) Decrease and increase (D) Decrease and decrease

Last Answer : (D) Decrease and decrease

In case of principal axes of a section (A) Sum of moment of inertia is zero (B) Difference of moment inertia is zero (C) Product of moment of inertia is zero (D) None of these

Description : In case of principal axes of a section  (A) Sum of moment of inertia is zero  (B) Difference of moment inertia is zero  (C) Product of moment of inertia is zero  (D) None of these 

Last Answer : (C) Product of moment of inertia is zero 

If the shear force along a section of a beam is zero, the bending moment at the section is (A) Zero (B) Maximum (C) Minimum (D) Average of maximum-minimum

Description : If the shear force along a section of a beam is zero, the bending moment at the section is  (A) Zero  (B) Maximum  (C) Minimum  (D) Average of maximum-minimum 

Last Answer : (B) Maximum 

In a loaded beam, the point of contraflexure occurs at a section where (A) Bending moment is minimum (B) Bending moment is zero or changes sign (C) Bending moment is maximum (D) Shearing force is maximum

Description : In a loaded beam, the point of contraflexure occurs at a section where (A) Bending moment is minimum (B) Bending moment is zero or changes sign (C) Bending moment is maximum (D) Shearing force is maximum

Last Answer : Answer: Option B

In the three moment equation method a. imaginary span unit span is assumed b. imaginary span zero span is assumed c. no imaginary span assumed d.twice the imaginary span is assumed

Description : In the three moment equation method a. imaginary span unit span is assumed b. imaginary span zero span is assumed c. no imaginary span assumed d.twice the imaginary span is assumed

Last Answer : b. imaginary span zero span is assumed

When does the growth rate of a population following the logistic model equal zero? The logistic model is given as dN/dt = rN(1–N/K) (a) when N/K equals zero (b) when death rate is greater than birth rate (c) when N/K is exactly one (d) when N nears the carrying capacity of the habitat.

Description : When does the growth rate of a population following the logistic model equal zero? The logistic model is given as dN/dt = rN(1–N/K) (a) when N/K equals zero (b) when death rate is greater than birth rate (c) when N/K is exactly one (d) when N nears the carrying capacity of the habitat.

Last Answer : (a) when N/K equals zero

Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Description : Terzaghi's analysis assumes: (A) Soil is homogeneous and isotropic (B) Elastic zone has straight boundaries inclined at = to the horizontal and plastic zones fully developed (C) Failure zones do not extend above the horizontal plane through the base of the footing (D) All the above

Last Answer : Answer: Option D

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

The ratio of lateral strain to axial strain of a homogeneous material, is known (A) Yield ratio (B) Hooke's ratio (C) Poisson's ratio (D) Plastic ratio

Description : The ratio of lateral strain to axial strain of a homogeneous material, is known  (A) Yield ratio  (B) Hooke's ratio  (C) Poisson's ratio  (D) Plastic ratio 

Last Answer : (C) Poisson's ratio 

Select incorrect statement from the following. In the Virtual work method, it is generally assumed that [ A ] Elastic deformations in the slab are negligible [ B ] Plastic deformations in the slab are negligible [ C ] Plastic deformations takes place at the yield lines [ D ] Both (a) and (b)

Description : Select incorrect statement from the following. In the Virtual work method, it is generally assumed that [ A ] Elastic deformations in the slab are negligible [ B ] Plastic deformations in the slab are negligible [ C ] Plastic deformations takes place at the yield lines [ D ] Both (a) and (b)

Last Answer : [ B ] Plastic deformations in the slab are negligible

The yield line ultimate moment is obtained when the yield line is --------------- to the direction of the reinforcement [ A ] Parallel [ B ] At right angles. [ C ] Passes through [ D ] Crosses at an angle of 45°

Description : The yield line ultimate moment is obtained when the yield line is --------------- to the direction of the reinforcement [ A ] Parallel [ B ] At right angles. [ C ] Passes through [ D ] Crosses at an angle of 45°

Last Answer : [ B ] At right angles.

The area of the cross-section of a road fully in banking shown in the given figure, is (A) [sb² + r² (2bd + sd)²]/(r² - s²) (B) [sb² + r² (2bd + sd)²]/(r² - s5 ) (C) [sb² + r² (2bd + sd)²]/(r - s) (D) None of these

Description : The area of the cross-section of a road fully in banking shown in the given figure, is (A) [sb² + r² (2bd + sd)²]/(r² - s²) (B) [sb² + r² (2bd + sd)²]/(r² - s5 ) (C) [sb² + r² (2bd + sd)²]/(r - s) (D) None of these

Last Answer : (A) [sb² + r² (2bd + sd)²]/(r² - s²)

In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Description : In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Last Answer : (a) Steel reinforcement is not fully stressed to its permissible value

The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Description : The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Last Answer : (a) Under-reinforced section

In a three hinged arch, the third hinge is generally kept at (A) Crown of the arch (B) Midpoint of the crown and left support hinge (C) Midpoint of the crown and right support hinge (D) None of these

Description : In a three hinged arch, the third hinge is generally kept at  (A) Crown of the arch  (B) Midpoint of the crown and left support hinge  (C) Midpoint of the crown and right support hinge  (D) None of these 

Last Answer : (A) Crown of the arch

Specific capacity or yield of wells, is generally expressed, as (A) m 3 per sec (B) m 3 /hour (C) m 3 /hour/m2 (D) m 3 /hour/m2 /m

Description : Specific capacity or yield of wells, is generally expressed, as  (A) m 3  per sec  (B) m 3 /hour  (C) m 3 /hour/m2 (D) m 3 /hour/m2 /m 

Last Answer : (D) m 3 /hour/m2 /m 

An under-reinforced section means (A) Steel is provided at the underside only (B) Steel provided is insufficient (C) Steel provided on one face only (D) Steel will yield first

Description : An under-reinforced section means (A) Steel is provided at the underside only (B) Steel provided is insufficient (C) Steel provided on one face only (D) Steel will yield first

Last Answer : Answer: Option D

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending strength and axial yield strength of material (c) Buckling strength based on the net area of the section and percentage elongation at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to reach its permissible limit before to reach yield stress in steel [ C ] stresses in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Description : In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to ... in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Last Answer : [ A ] the stress in steel to reach its yield limit before concrete failure

In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to reach its permissible limit before to reach yield stress in steel [ C ] stresses in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Description : In general in the design of a section by limit method, it is assumed that [ A ] the stress in steel to reach its yield limit before concrete failure [ B ] the stress in concrete to ... in both concrete and steel reach their permissible values simultaneously [ D ] none of the above are correct

Last Answer : [ A ] the stress in steel to reach its yield limit before concrete failure

To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Description : To ensure that the hogging bending moment at two points of suspension of a pile of length L equals the sagging moment at its centre, the distances of the points of suspension from either end, is (A) 0.107 L (B) 0.207 L (C) 0.307 L (D) 0.407 L

Last Answer : Answer: Option B

In how many ways can the string A ∩ B - A ∩ B - A be fully parenthesized to yield an infix expression? (A) 15 (B) 14 (C) 13 (D) 12

Description : In how many ways can the string A ∩ B - A ∩ B - A be fully parenthesized to yield an infix expression? (A) 15 (B) 14 (C) 13 (D) 12

Last Answer : (B) 14

Best side slope for most economical trapezoidal section in open channel flow, wherein side slopes are defined by : X horizontal to 1 vertical, is when X equals : (a) 0.404 (b) 0.500 (c) 0.577 (d) 0.673

Description : Best side slope for most economical trapezoidal section in open channel flow, wherein side slopes are defined by : X horizontal to 1 vertical, is when X equals : (a) 0.404 (b) 0.500 (c) 0.577 (d) 0.673

Last Answer : (c) 0.577

The discharge through a channel of rectangular section will be maximum, if (A) Its depth is twice the breadth (B) Its breadth is twice the depth (C) Its depth is thrice the breadth (D) Its breadth is thrice the depth

Description : The discharge through a channel of rectangular section will be maximum, if (A) Its depth is twice the breadth (B) Its breadth is twice the depth (C) Its depth is thrice the breadth (D) Its breadth is thrice the depth

Last Answer : Answer: Option B

The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom (C) The sloping side is equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Description : The discharge through a channel of trapezoidal section is maximum when (A) Width of channel at the top is equal to twice the width at the bottom (B) Depth of channel is equal to the width at the bottom ... equal to half the width at the top (D) The sloping side is equal to the width at the bottom

Last Answer : Answer: Option C

The most economical section of a rectangular channel is one which has hydraulic mean depth or hydraulic radius equal to (A) Half the depth (B) Half the breadth (C) Twice the depth (D) Twice the breadth

Description : The most economical section of a rectangular channel is one which has hydraulic mean depth or hydraulic radius equal to (A) Half the depth (B) Half the breadth (C) Twice the depth (D) Twice the breadth

Last Answer : Answer: Option A

Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild steel bar in tension from initial zero strain to failure is (a) 4, 1, 2, 3 and 5 (b) 1, 4, 3, 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Last Answer : (c) 4, 1, 3, 5 and 2

The difference of level between a point below the plane of sight and one above, is the sum of two staff readings and an error would be produced equal to (A) The distance between the zero of gradient and the foot of the staff (B) Twice the distance between the zero of graduation and the foot of the staff (C) Thrice the distance between the zero of graduation and the foot of the staff (D) None of the above

Description : The difference of level between a point below the plane of sight and one above, is the sum of two staff readings and an error would be produced equal to (A) The distance between the zero of ... Thrice the distance between the zero of graduation and the foot of the staff (D) None of the above

Last Answer : (B) Twice the distance between the zero of graduation and the foot of the staff

When all the limiting reactant is consumed in the reaction, the operational yield __________ the relative yield. (A) Is greater than (B) Is smaller than (C) Equals (D) Can be either greater or smaller than (depends on the type of reaction)

Description : When all the limiting reactant is consumed in the reaction, the operational yield __________ the relative yield. (A) Is greater than (B) Is smaller than (C) Equals (D) Can be either greater or smaller than (depends on the type of reaction)

Last Answer : (C) Equals

In the virtual work method of plastic analysis of steel structures, the virtual quantity is (a) Slope (b) Moment (c) Load (d) Displacement

Description : In the virtual work method of plastic analysis of steel structures, the virtual quantity is (a) Slope (b) Moment (c) Load (d) Displacement

Last Answer : (d) Displacement

In plastic analysis, the shape factor for a circular section, is (A) 1.5 (B) 1.6 (C) 1.7 (D) 1.75

Description : In plastic analysis, the shape factor for a circular section, is  (A) 1.5  (B) 1.6  (C) 1.7  (D) 1.75 

Last Answer : (C) 1.7 

In plastic analysis, the shape factor for a triangular section, is (A) 1.5 (B) 1.34 (C) 2.34 (D) 2.5

Description : In plastic analysis, the shape factor for a triangular section, is  (A) 1.5  (B) 1.34  (C) 2.34  (D) 2.5 

Last Answer : (C) 2.34 

In plastic analysis, the shape factor for rectangular section, is (A) 1.4 (B) 1.5 (C) 1.6 (D) 1.7

Description : In plastic analysis, the shape factor for rectangular section, is  (A) 1.4  (B) 1.5  (C) 1.6  (D) 1.7

Last Answer : (B) 1.5 

When the velocity of an enzymatic reaction equals Vmax, substrate concentration is (A) Half of Km (B) Equal to Km (C) Twice the Km (D) Far above the Km

Description : When the velocity of an enzymatic reaction equals Vmax, substrate concentration is (A) Half of Km (B) Equal to Km (C) Twice the Km (D) Far above the Km

Last Answer : Answer : D

The sum of twice the square of a number and 7 times the number equals 15. What is the number? 1.1/2 2.3/4 3.3/2 4.5/3

Description : The sum of twice the square of a number and 7 times the number equals 15. What is the number? 1.1/2 2.3/4 3.3/2 4.5/3

Last Answer : Answer-3 (3/2) Explanation:-2x^2 + 7x = 15 2x^2 + 7x – 15 = 0 2x^2 + 10x-3x – 15 = 0 2x(x+5)-3(x+5) = 0 (x+5)(2x-3) = 0 x = -5 or x = 3/2

The first fully synthetic plastic was_________. a) Bakelite b)melamine c)Teflon d)polythene

Description : The first fully synthetic plastic was_________. a) Bakelite b)melamine c)Teflon d)polythene

Last Answer : a) Bakelite

The moment of inertia of a rectangular section of width and depth about an axis passing through C.G. and parallel to its width is (A) BD²/6 (B) BD3 /6 (C) BD3 /12 (D) B²D/6

Description : The moment of inertia of a rectangular section of width and depth about an axis passing  through C.G. and parallel to its width is  (A) BD²/6  (B) BD3 /6  (C) BD3 /12  (D) B²D/6 

Last Answer : (C) BD3 /12 

If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of elasticity stress and the depth of the neutral axis at section, then (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Description : If M, I, R, E, F, and Y are the bending moment, moment of inertia, radius of curvature, modulus of  elasticity stress and the depth of the neutral axis at section, then  (A) M/I = R/E = F/Y (B) I/M = R/E = F/Y (C) M/I = E/R = E/Y (D) M/I = E/R = Y/F

Last Answer : (C) M/I = E/R = E/Y

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis