A member which does not regain its original shape after removed of load producing deformation is said (A) Plastic (B) Elastic (C) Rigid (D) None of these

A member which does not regain its original shape after removed of load producing deformation
is said
(A) Plastic
(B) Elastic
(C) Rigid
(D) None of these
by

1 Answer

Answer :

(A) Plastic
by

Related questions

A material is said to be perfectly elastic if (A) It regains its original shape on removal of the load (B) It regains its original shape partially on removal of the load (C) It does not regain its original shape at all (D) None of these

Description : A material is said to be perfectly elastic if  (A) It regains its original shape on removal of the load  (B) It regains its original shape partially on removal of the load  (C) It does not regain its original shape at all  (D) None of these

Last Answer : (A) It regains its original shape on removal of the load 

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Description : Which of the following are true about plasticity? a) Permanent Deformation b) Ability to retain deformation under load or after removal of load c) Plastic deformation is greater than elastic deformation d) All of the mentioned

Last Answer : d) All of the mentioned

The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Description : The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Last Answer : Ductile

Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is proportional to the age of the member at the time of loading. (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members

Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Description : The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Last Answer : Option C

48. A perfectly elastic body (a) Can move freely (b) Has perfectly smooth surface (c) Is not deformed by any external surface (d) Recovers its original size and shape when the deforming force is removed.

Description : 48. A perfectly elastic body (a) Can move freely (b) Has perfectly smooth surface (c) Is not deformed by any external surface (d) Recovers its original size and shape when the deforming force is removed.

Last Answer : d) Recovers its original size and shape when the deforming force is removed.

Hot & cold working of material causes its __________ deformation. (A) Visco-elastic (B) Isotropic (C) Elastic (D) Plastic

Description : Hot & cold working of material causes its __________ deformation. (A) Visco-elastic (B) Isotropic (C) Elastic (D) Plastic

Last Answer : (D) Plastic

Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) The damping capacity of a material is due to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Description : Pick out the correct statement. (A) Materials exhibiting high elasticity obey Hooke's law (B) The elastic behaviour of rubber under compression is the same as its behaviour under tension (C) ... to its plastic deformation (D) The stress required to cause plastic flow in polycrystalline material is

Last Answer : Option B

Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Description : Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Last Answer : ductile substances

In forging, metal is in which of the following stage? a) Elastic b) Plastic c) Can be in any stage d) Rigid

Description : In forging, metal is in which of the following stage? a) Elastic b) Plastic c) Can be in any stage d) Rigid

Last Answer : b) Plastic

In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line of the beam before bending remain plane after bending (D) Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Description : In a singly reinforced beam (A) Compression is borne entirely by concrete (B) Steel possesses initial stresses when embedded in concrete (C) Plane sections transverse to the centre line ... Elastic moduli for concrete and steel have different values within the limits of deformation of the beam

Last Answer : Answer: Option C

The tendency of a deformed solid to regain its actual proportions instantly upon unloading known as ______________ a) Perfectly elastic b) Delayed elasticity c) Inelastic effect d) Plasticity

Description : The tendency of a deformed solid to regain its actual proportions instantly upon unloading known as ______________ a) Perfectly elastic b) Delayed elasticity c) Inelastic effect d) Plasticity

Last Answer : a) Perfectly elastic

What Properties Are Needed To Be Considered For Application Calling For Following Requirements? I) Rigidity. Ii) Strength Of No Plastic Deformation Under Static Load. Iii) Strength To Withstand Overload Without Fracture.

Description : What Properties Are Needed To Be Considered For Application Calling For Following Requirements? I) Rigidity. Ii) Strength Of No Plastic Deformation Under Static Load. Iii) Strength To Withstand Overload Without Fracture.

Last Answer : i) Reliability – elastic modulus and yield strength. ii) Strength (for no plastic deformation under static loading) – yield point. iii) Strength (overload) – Toughness and impact resistance. iv) Wear resistance – Hardness. v) Reliability and safety – Endurance limit and yield.

The stress at which extension of a material takes place more quickly as compared to the increase in load, is called (A) Elastic point (B) Plastic point (C) Breaking point (D) Yielding point

Description : The stress at which extension of a material takes place more quickly as compared to the increase in load, is called (A) Elastic point (B) Plastic point (C) Breaking point (D) Yielding point

Last Answer : (D) Yielding point

-------is a rigid body transformation that moves objects without deformation. a.Rotation b.Scaling c.Translation d.All of the mentioned

Description : -------is a rigid body transformation that moves objects without deformation. a.Rotation b.Scaling c.Translation d.All of the mentioned

Last Answer : c.Translation

If Q is load factor, S is shape factor and F is factor of safety in elastic design, the following: (A) Q = S + F (B) Q = S - F (C) Q = F - S (D) Q = S × F

Description : If Q is load factor, S is shape factor and F is factor of safety in elastic design, the following:  (A) Q = S + F (B) Q = S - F (C) Q = F - S (D) Q = S × F

Last Answer : (D) Q = S × F

Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's law is equally applicable to concrete as well as to steel (C) Variation of stress in reinforcement due to changes in external loading is negligible (D) All the above

Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above

Last Answer : Answer: Option D

If a soil undergoes a change in shape and volume by application of external loads over it, but recovers its shape and volume immediately after removal of the load, the property of the soil is said to be (A) Resilience of soils (B) Elasticity of soils (C) Compressibility of soils (D) None of these

Description : If a soil undergoes a change in shape and volume by application of external loads over it, but recovers its shape and volume immediately after removal of the load, the property of the soil is said to ... Resilience of soils (B) Elasticity of soils (C) Compressibility of soils (D) None of these

Last Answer : Answer: Option B

Is it true Elastic deformation occurs when a material deforms as stress is applied?

Description : Is it true Elastic deformation occurs when a material deforms as stress is applied?

Last Answer : Yes

Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Description : Lead pipe is (A) Especially resistant to solutions containing H2SO4 (B) Usually joined by burning (e.g. by melting to adjacent pieces with a torch) (C) Having very low elastic limit resulting in permanent deformation from either mechanical or thermal strain (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Description : Hooke's law (A) Applies to elastic deformation (B) Applies beyond limit of proportionality in stress-strain curve (C) States that stress is inversely proportional to strain upto elastic limit (D) None of these

Last Answer : (A) Applies to elastic deformation

Pick up the correct statement from the following: (A) A ductile material has large plastic zone (B) A brittle material has no plastic zone (C) A rigid material has no plastic zone (D) All the above

Description : Pick up the correct statement from the following: (A) A ductile material has large plastic zone (B) A brittle material has no plastic zone (C) A rigid material has no plastic zone (D) All the above

Last Answer : All the above

The thermosetting plastic (A) Becomes rigid when moulded at suitable pressure and temperature (B) At 127°C to 177°C permanently set and further application of heat does not soften it (C) Chars at 343°C (D) All the above

Description : The thermosetting plastic (A) Becomes rigid when moulded at suitable pressure and temperature (B) At 127°C to 177°C permanently set and further application of heat does not soften it (C) Chars at 343°C (D) All the above

Last Answer : Answer: Option D

Plastic (A) Is an organic substance (B) Consists of natural or synthetic binders (C) Finished products are rigid and stable at normal temperature (D) All the above

Description : Plastic (A) Is an organic substance (B) Consists of natural or synthetic binders (C) Finished products are rigid and stable at normal temperature (D) All the above

Last Answer : Answer: Option D

Number of unknown internal forces in each member of a rigid jointed plane frame is (A) 1 (B) 2 (C) 3 (D) 6

Description : Number of unknown internal forces in each member of a rigid jointed plane frame is (A) 1 (B) 2 (C) 3 (D) 6

Last Answer : (C) 3

A highly elastic material is deformed least on loading and retains its original form on removal of the load. Which of the following is the most elastic material? (A) Steel (B) Glass (C) Rubber (D) Brass

Description : A highly elastic material is deformed least on loading and retains its original form on removal of the load. Which of the following is the most elastic material? (A) Steel (B) Glass (C) Rubber (D) Brass

Last Answer : Option A

The law which states, "Within elastic limits strain produced is proportional to the stress producing it", is known as (A) Bernoulli's law (B) Stress law (C) Hooke's law (D) Poisson's law

Description : The law which states, "Within elastic limits strain produced is proportional to the stress producing  it", is known as  (A) Bernoulli's law  (B) Stress law  (C) Hooke's law  (D) Poisson's law

Last Answer : (C) Hooke's law 

The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Description : The deformation of a spring produced by a unit load is called (A) Stiffness (B) Flexibility (C) Influence coefficient (D) Unit strain

Last Answer : (B) Flexibility

A material no longer behaves elastically beyond (A) Plastic limit (B) Limiting load (C) Elastic limit (D) Breaking load

Description : A material no longer behaves elastically beyond (A) Plastic limit (B) Limiting load (C) Elastic limit (D) Breaking load

Last Answer : (C) Elastic limit

At ‘yield point’ of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become plastic C. even the plastic stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Description : At yield point' of a copper wire A. the load hasn't exceeded the elastic limit yet; so, Hooke's law applies B. the load has already exceeded the elastic limit and the material has become ... stage has passed and the wire has snapped already D. Like Brass and Bronze, Copper has no yield poin

Last Answer : the load has already exceeded the elastic limit and the material has become plastic

The stress at which extension of a material takes place more quickly as compared to increase in load, is called (a) No elastic zone (b) Plastic point (c) Yield point (d) Breaking point

Description : The stress at which extension of a material takes place more quickly as compared to increase in load, is called (a) No elastic zone (b) Plastic point (c) Yield point (d) Breaking point

Last Answer : (c) Yield point

Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Description : Reinforced concrete slab supported only on columns is said to be [ A ] Rigid slab [ B ] Flat slab [ C ] Both(a) and (b) [ D ] None of the above.

Last Answer : [ B ] Flat slab

Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Description : Ability of a material to absorb energy in deformation in the plastic range is characterised as its (A) Ductility (B) Toughness (C) Creep (D) Resilience

Last Answer : (B) Toughness

Pick out the correct statement. (A) Stainless steel is nothing but chromium coated steel (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal (C) Plastic deformation of a material is its temporary distortion under the action of applied stress (D) Rusting of iron is not electrochemical in nature

Description : Pick out the correct statement. (A) Stainless steel is nothing but chromium coated steel (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal (C) ... its temporary distortion under the action of applied stress (D) Rusting of iron is not electrochemical in nature

Last Answer : (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal

Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these

Description : Every material obeys the Hooke's law within its (A) Elastic limit (B) Plastic point (C) Limit of proportionality (D) None of these

Last Answer : (C) Limit of proportionality

The deformation of body is the change in its a) Shape b) Length c) Area d) All of above

Description : The deformation of body is the change in its a) Shape b) Length c) Area d) All of above

Last Answer : d) All of above

…. is the property of a material which enables it to resist plastic deformation.

Description : …. is the property of a material which enables it to resist plastic deformation.

Last Answer : …. is the property of a material which enables it to resist plastic deformation. (A) elasticity (B) plasticity (C) hardness (D) ductility

Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Description : Slow plastic deformation of metals under a constant stress is termed as __________ failure. (A) Fatigue (B) Endurance (C) Creep (D) None of these

Last Answer : (C) Creep

Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Description : Which of the following help in accomplishing the locking? a) Creating supplementary friction b) Using special locking devices like split pins c) By plastic deformation d) All of the listed

Last Answer : d) All of the listed

There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Last Answer : b) False

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength

An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Description : An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Last Answer : (A) Sewage sludge

The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience