The water level in an open well was depressed by pumping 2.5 m and recuperated 2.87 m in 3
hours and 50 minutes. The yield of the well per minute is
(A) 0.0033
(B) 0.0044
(C) 0.0055
(D) 0.0066
Description : A well penetrates to 30 m below the static water table. After 24 hours of pumping at 31.40 litres/minute, the water level in a test well at a distance of 80 m is lowered by 0.5 m and in a well 20 m away water is ... 1.185 m2 /minute (B) 1.285 m2 /minute (C) 1.385 m2 /minute (D) 1.485 m2 /minute
Last Answer : Answer: Option C
Description : While determining the yield of open wells by the pumping test (A) Velocity of recharging water, increases with depression head (B) Depression head resulting at critical velocity, is called critical ... (D) Maximum safe yield of an open well, is expected at critical depression head
Last Answer : (D) Maximum safe yield of an open well, is expected at critical depression head
Description : The difference between static water level and pumping water level is known as: a drawdown b well yield c specific capacity d all are correct
Last Answer : a drawdown
Description : The design yield stress of steel according to IS: 4561978 is: (A) 0.37 fy (B) 0.57 fy (C) 0.67 fy (D) 0.87 fy Where fy is the characteristic yield strength of steel
Last Answer : Answer: Option D
Description : Design yield stress for steel in tension and compression is [ A ] 0.65 fy [ B ] 0.87 fy [ C ] 0.75 fy [ D ] None of the above
Last Answer : [ B ] 0.87 fy
Description : For M 150 grade concrete (1:2:4) the moment of resistance factor is (A) 0.87 (B) 8.50 (C) 7.50 (D) 5.80
Last Answer : Answer: Option B
Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec
Description : Pick up the correct statement from the following: (A) The water level in a still well, represents the ground water table level (B) The difference between water table level and the water ... water table surrounding a well during pumping, forms a cone of depression (D) All the above
Last Answer : (D) All the above
Description : In the illustration, the purpose of part B is to _________. EL-0033 A. increase resistance in series with the contacts as they close to prevent arcing B. create a magnetic field in the steel ... event of an overload D. provide ventilation to the contact when the breaker is close to rated capacity
Last Answer : Answer: B
Description : Pick up the correct statement from the following: (A) Detention period for plain sedimentation tanks ranges between 4 to 8 hours (B) Detention period for sedimentation tanks, using coagulants usually ... in sedimentation tanks, is generally limited to 0.3 m/minute (D) All the above
Description : As shown in the illustration, which of the symbols is used to represent a capacitor? EL-0066 A. A B. B C. C D. D
Description : The settling velocity of the particles larger than 0.06 mm in a settling tank of depth 2.4 is 0.33 m per sec. The detention period recommended for the tank, is A. 30 minutes B. 1 hour C. 1 hour and 30 minutes D. 2 hours
Last Answer : ANS: D
Description : The reading at 'M' on the megger scale illustrated, is ____. EL-0044 A. 7.1 meg ohms B. 71 meg ohms C. .71 meg ohms D. 200,000,000 ohms
Last Answer : Answer: A
Description : The reading at 'M' on the megger scale shown in the illustration, is __________. EL-0044 A. 7.1 meg ohms B. .71 meg ohms C. 71 meg ohms D. 200,000,000 ohms
Description : For the same draw down in two observations wells at distances r1 and r2, the times after start of pumping are t1 and t2 hours respectively. The relation which holds good is (A) t2 = r2/r1 × t1 (B) t2 = (r2/r1)² × t1 (C) t2 = (r2/r1)3 × t1 (D) t2 = (r2/r1) × t1 2
Last Answer : (B) t2 = (r2/r1)² × t1
Description : The expected discharge to be obtained from an open well sunk in coarse sand is 0.0059 cumec. If the working depression head of the well is 3 m, the minimum diameter of the well, is (A) 2 m (B) 2.25 m (C) 2.50 m (D) 3.00 m
Last Answer : (D) 3.00 m
Description : An alarm clock runs 4 minutes slow every hour. It was set right 3 1/2 hours ago. Now another clock which is correct shows noon. In how many minutes, to the nearest minutes, to the nearest minute, will the alarm clock show noon? -Riddles
Last Answer : In 3 1/2 hours the alarm clock has become 14 minutes slow. At noon the alarm clock will fall behind approximently an additional minute. Its hands will show noon in 15 minutes.
Description : If Q is discharge is cubic metres per sec and D is the economical diameter of the pipe. According to Lea (A) D = 0.67 to 0.87 Q (B) D = 0.77 to 0.97 Q (C) D = 0.97 to 1.22 Q (D) D = 1.22 to 1.33 Q
Last Answer : (C) D = 0.97 to 1.22 Q
Description : The slope correction for a 3° slope for a length of 100 m, is (A) -0.11 m (B) -0.12 m (C) -1.87 m (D) -0.137 m
Last Answer : (D) -0.137 m
Description : A structure is erected on an impervious clay whose thickness is 12 m. Drainage is possible both at upper and lower surfaces. Coefficient of consolidation is 0.015 cm2 per minute. For attaining 50% consolidation with a ... 20, the number of days required (A) 3233 (B) 3123 (C) 33331 (D) 3313
Description : It takes 0.4 hrs to drive from the garage to the head of the route, 0.4 hrs to drive between the route head and disposal site and 0.25 hrs to return from the disposal site. It takes 0.2 hrs to offload a truck at the ... loading time as 30 minutes. (a) 4.15 hrs (b) 4.25 hrs (c) 4.75 hrs (d) 4.85 hrs
Last Answer : (a) 4.15 hrs
Description : If the illustrated device has a step-up ratio of 10 to 1 what voltage be measured at the secondary shortly after the primary of the device is connected to 110 volts DC with a current of 12 amps? EL-0055 A. 0 volts B. 110 volts C. 1000 volts D. 1100 volts
Description : A transport company is running five buses between two towns, which are 50 kms apart. Seating capacity of each bus is 50 passengers. Actually passengers carried by each bus were 75% of seating capacity. All buses ran on all days of ... (a) 2,81,250 (b) 1,87,500 (c) 5,62,500 (d) None of the above
Last Answer : (c) 5,62,500
Description : Ravi walks to and fro to a Gym. He spends 30 minutes in gym. If he walks at speed of 20 km an hour, he returns to home at 8.00 a.m. If he walks at 30 km an hour, he returns to home at 7.30 a.m. How fast must he walk in order to return at 7.15 hours? a) 40 km/hr b) 30 km/hr c) 60 km/hr d) 50 km/hr
Last Answer : A As per the question, let D be the total distance and ‘t’ is the time taken. So we have: D=20t 20t =30(t-0.5) 20t=30t-15 10t=15 t=3/2 D= 30 km Now, for the condition given we have: 30=S(t-3/4) 30=S(3/2-3/4) 30=S((6-3)/4) 30=S(3/4) S=40 km/hr
Description : The major limitation of metallic recuperated is ------- a) Limitation of handling COx, NOx etc. b) Limitation of reduced life for handling temperature more than 1000 oC c) Manufacturing difficulty of the required design d) None of the above
Last Answer : Limitation of reduced life for handling temperature more than 1000 oC
Description : Recuperated will be more efficient if the flow path of hot and cold fluids is in: a) Co-current mode b) Counter current mode c) Cross current mode d) Cone of the above
Last Answer : Counter current mode
Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above
Last Answer : Billet Reheating Furnace
Description : Specific yield of a well is (A) Quantity of water than can be drawn from the well (B) Flow of water per unit time (C) Total quantity of water available in the well (D) Quantity of water per unit time per unit draw-down
Last Answer : (C) Total quantity of water available in the well
Description : S1 and S2 are the draw downs in an observation well at times t1 and t2 after pumping. For discharge Q and coefficient of transmissibility T, the relationship, is (A) S2 - S1 = (2.3Q/ ) log10 (t2/t1) (B) S2 - S1 ... - S1 = (2.3Q/4 ) loge (t2/t1) (D) S2 - S1 = (2.3Q/4 ) loge (t1/t2
Last Answer : (B) S2 - S1 = (2.3Q/4 ) log10 (t2/t1)
Description : Corrosion of well pipes may not be reduced by (A) Reducing the draw down and the pumping rate (B) Reducing the flow velocity (C) Using thicker pipes (D) Using screens having larger area of openings
Last Answer : (D) Using screens having larger area of openings
Description : The efficiency of a pumping set, is generally assumed (A) 50 % (B) 55 % (C) 60 % (D) 65 %
Last Answer : (D) 65 %
Description : A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff readings at and were 1.22 and 1.06. With the level set up at , the readings at and were 1.55 and ... upwards (B) 0.04 m inclined downwards (C) 0.04 m inclined upward (D) None of these
Last Answer : (B) 0.04 m inclined downwards
Description : A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m ... collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m
Last Answer : (D) 0.060 m
Description : Three pipes, A, B, & C are attached to a tank. A & B can fill it in 20 & 30 minutes respectively while C can empty it in 15 minutes. If A, B & C are kept open successively for 1 minute each, how soon will the tank be filled?
Last Answer : Answer: 167 minutes.
Description : If the effective working time is 7 hours and per batch time of concrete is 3 minutes, the output of a concrete mixer of 150 litre capacity, is (A) 15,900 litres (B) 16,900 litres (C) 17,900 litres (D) 18,900 litres
Last Answer : (D) 18,900 litres
Description : As per IS specifications, the maximum final setting time for ordinary Portland cement should be (A) 30 minutes (B) 1 hour (C) 6 hours (D) 10 hour
Description : When the reduced level of the water source is higher than the reduced level of the consumer's place, water is generally supplied (A) By pumping system (B) By gravitational system (C) Both (a) and (b) (D) All the above
Last Answer : (B) By gravitational system
Description : A tractor shovel has a purchase price of Rs. 4.7 lacs and could save the organization an amount of rupees one lac per year on operating costs. The salvage value after the amortization period is 10% of the purchase price. The ... will be (A) 3.7 years (B) 4.23 years (C) 5 years (D) 7.87 years
Last Answer : (B) 4.23 years
Description : The reading at 'V' on the megger scale shown in the illustration, is __________. EL-0044 A. 40 meg ohms B. 0.40 meg ohms C. 4.0 kilo ohms D. 40,000 ohms
Last Answer : Answer: D
Description : From the Survey of India map, the distance of the critical point is 20 km and difference in elevation is 193 m. The over land flow time, is (A) 2 hours (B) 3 hours (C) 2 hours and 30 minutes (D) 4 hours
Description : In case of Imhoff tanks, A. The shape is rectangular B. Detention period is 2 hours C. The velocity of flow is restricted to 0.30 m/minute D. All the above
Description : An intense rain is falling at a uniform rate of 7.5 cm/hour for a period of 60 minutes on a basin whose area is 500 hectares. If the average infiltration capacity during the entire rain period is assumed to be 1.5 ... of the basin, is (A) 40 cumecs (B) 60 cumecs (C) 80 cumecs (D) 100 cumecs
Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : A load with an impedance of 440 ohms is connected across the secondary of the device illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given
Description : Component F in the illustrated device is for _________. EL-0033 A. short circut protection B. latching the trip unit closed after resetting the breaker C. overload protection D. providing a flexible connection between the input terminal G and the tripping unit E
Last Answer : Answer: C
Description : In the illustration, the component labeled D is a ______. EL-0033 A. fixed contact B. moving contact C. trip bar D. bimetallic strip
Description : In the illustration the component C is the ____________. EL-0033 A. fixed contact B. moving contact C. connection terminal D. trip bar
Description : In the illustration, the the device E is the______. EL-0033 A. bimetal strip B. moving contact C. trip bar D. handle
Description : What A scuba driver’s depth was changed from –20 ft to –63 ft in 10 minutes. Find his average change in depth per minute?
Last Answer : 4.3 feet per minute-20 - -63 = 4343/10 = 4.3