A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction

A backmix reactor
(A) Is same as plug-flow reactor
(B) Is same as ideal stirred tank reactor
(C) Employs mixing in axial direction only
(D) Is most suitable for gas phase reaction
by

1 Answer

Answer :

(B) Is same as ideal stirred tank reactor
by

Related questions

A back mix reactor is (A) Suitable for gas phase reactions (B) Ideal at very low conversion (C) Same as plug flow reactor (PFR) (D) Same as ideal stirred tank reactor

Description : A back mix reactor is (A) Suitable for gas phase reactions (B) Ideal at very low conversion (C) Same as plug flow reactor (PFR) (D) Same as ideal stirred tank reactor

Last Answer : (D) Same as ideal stirred tank reactor

Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal mixed reactor at steady state, the exit stream has the samecomposition as fluid within the reactor and the space time is equivalent toholding time for constant density system(C) Plug flow reactor (PFR) is always smaller than mixed reactor for allpositive reaction orders for a particular duty(D) Reaction rate does not decrease appreciably as the reaction proceeds incase of an autocatalytic reaction

Description : Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal ... D) Reaction rate does not decrease appreciably as the reaction proceeds in case of an autocatalytic reaction

Last Answer : (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity

In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Description : In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Last Answer : (B) Velocity of reaction can be controlled

Which of the following is the most suitable for very high pressure gas phase reaction? (A) Batch reactor (B) Tubular flow reactor (C) Stirred tank reactor (D) Fluidised bed reactor

Description : Which of the following is the most suitable for very high pressure gas phase reaction? (A) Batch reactor (B) Tubular flow reactor (C) Stirred tank reactor (D) Fluidised bed reactor

Last Answer : (B) Tubular flow reactor

For nearly isothermal operation involving large reaction time in a liquid-phase reaction, the most suitable reactor is a __________ reactor. (A) Stirred tank (B) Tubular flow (C) Batch (D) Fixed bed

Description : For nearly isothermal operation involving large reaction time in a liquid-phase reaction, the most suitable reactor is a __________ reactor. (A) Stirred tank (B) Tubular flow (C) Batch (D) Fixed bed

Last Answer : (A) Stirred tank

Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a measure of its capacity and is equal to the residence time when the density of reaction mixture is constant (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty (D) In an ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Description : Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a ... ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Last Answer : (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty

A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Description : A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Last Answer : (C) Presence of lateral mixing

The most unsuitable reactor for carrying out reactions in which high reactant concentration favours high yields is (A) Backmix reactor (B) Plug flow reactor (C) Series of CSTR (D) PFR in series

Description : The most unsuitable reactor for carrying out reactions in which high reactant concentration favours high yields is (A) Backmix reactor (B) Plug flow reactor (C) Series of CSTR (D) PFR in series

Last Answer : A) Backmix reactor

The conversion XA and residence time data are collected for zero order liquid phase reaction in a stirred tank reactor. Which of the following will be a straight line? (A) XA Vs . τ (B) XA Vs ln τ (C) XA /(1 - XA )Vs τ (D) XA (1 - XA )Vs τ

Description : The conversion XA and residence time data are collected for zero order liquid phase reaction in a stirred tank reactor. Which of the following will be a straight line? (A) XA Vs . τ (B) XA Vs ln τ (C) XA /(1 - XA )Vs τ (D) XA (1 - XA )Vs τ

Last Answer : (A) XA Vs . τ

A stirred tank reactor compared to tubular-flow reactor provides (A) More uniform operating conditions (B) Permits operation at the optimum temperature for a long reaction time (C) Higher overall selectivity for a first order consecutive reaction (D) All (A), (B) and (C

Description : A stirred tank reactor compared to tubular-flow reactor provides (A) More uniform operating conditions (B) Permits operation at the optimum temperature for a long reaction time (C) Higher overall selectivity for a first order consecutive reaction (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

In a continuous flow stirred tank reactor, the composition of the exit stream (A) Is same as that in the reactor (B) Is different than that in the reactor (C) Depends upon the flow rate of inlet stream (D) None of these

Description : In a continuous flow stirred tank reactor, the composition of the exit stream (A) Is same as that in the reactor (B) Is different than that in the reactor (C) Depends upon the flow rate of inlet stream (D) None of these

Last Answer : (A) Is same as that in the reactor

For the same residence time, which one will give the maximum conversion? (A) Single stirred tank (v = 5 litres) (B) Two stirred tank (each of 2.5 litres) in series (C) Stirred tank followed by tubular flow reactor (each of 2.5 litres) (D) Single tubular flow reactor (v = 5 litres)

Description : For the same residence time, which one will give the maximum conversion? (A) Single stirred tank (v = 5 litres) (B) Two stirred tank (each of 2.5 litres) in series (C) Stirred tank followed by tubular flow reactor (each of 2.5 litres) (D) Single tubular flow reactor (v = 5 litres)

Last Answer : (D) Single tubular flow reactor (v = 5 litres)

Backmixing is most predominant in (A) A well stirred batch reactor (B) A plug-flow reactor (C) A single CSTR (D) CSTR's connected in series

Description : Backmixing is most predominant in (A) A well stirred batch reactor (B) A plug-flow reactor (C) A single CSTR (D) CSTR's connected in series

Last Answer : (C) A single CSTR

For a fluidised bed reactor, the most suitable/relevant model is a __________ model. (A) Tank in series (B) Bubbling bed (C) Plug flow (D) None of these

Description : For a fluidised bed reactor, the most suitable/relevant model is a __________ model. (A) Tank in series (B) Bubbling bed (C) Plug flow (D) None of these

Last Answer : (B) Bubbling bed

In an ideal tubular-flow reactor (A) There is no mixing in longitudinal direction (B) Mixing takes place in radial direction (C) There is a uniform velocity across the radius (D) All (A), (B) and (C)

Description : In an ideal tubular-flow reactor (A) There is no mixing in longitudinal direction (B) Mixing takes place in radial direction (C) There is a uniform velocity across the radius (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The gas phase reaction 2A ⇌ B is carried out in an isothermal plug flow reactor. The feed consists of 80 mole % A and 20 mole % inerts. If the conversion of A at the reactor exit is 50%, then CA/CA0 at the outlet of the reactor is (A) 2/3 (B) 5/8 (C) 1/3 (D) 3/8

Description : The gas phase reaction 2A ⇌ B is carried out in an isothermal plug flow reactor. The feed consists of 80 mole % A and 20 mole % inerts. If the conversion of A at the reactor exit is 50%, then CA/CA0 at the outlet of the reactor is (A) 2/3 (B) 5/8 (C) 1/3 (D) 3/8

Last Answer : (B) 5/8

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

A reversible liquid phase endothermic reaction is to be carried out in a plug flow reactor. For minimum reactor volume, it should be operated such that the temperature along the length (A) Decreases (B) Increases (C) Is at the highest allowable temperature throughout (D) First increases and then decreases

Description : A reversible liquid phase endothermic reaction is to be carried out in a plug flow reactor. For minimum reactor volume, it should be operated such that the temperature along the length (A) ... Increases (C) Is at the highest allowable temperature throughout (D) First increases and then decreases

Last Answer : (C) Is at the highest allowable temperature throughout

An endothermic aqueous phase first order irreversible reaction is carried out in an adiabatic plug flow reactor. The rate of reaction: (A) Is maximum at the inlet of the reactor (B) Goes through a maximum along the length of the reactor (C) Goes through a minimum along the length of the reactor (D) Is maximum at the exit of the reactor

Description : An endothermic aqueous phase first order irreversible reaction is carried out in an adiabatic plug flow reactor. The rate of reaction: (A) Is maximum at the inlet of the reactor (B) Goes through a maximum ... through a minimum along the length of the reactor (D) Is maximum at the exit of the reactor

Last Answer : (A) Is maximum at the inlet of the reactor

A trickle bed reactor is the one, which (A) Has altogether three streams either entering or leaving (B) Processes three reactants at different flow rates (C) Processes three reactants with same flow rate (D) Employs all the three phases (i.e. solid, liquid and gas)

Description : A trickle bed reactor is the one, which (A) Has altogether three streams either entering or leaving (B) Processes three reactants at different flow rates (C) Processes three reactants with same flow rate (D) Employs all the three phases (i.e. solid, liquid and gas)

Last Answer : (D) Employs all the three phases (i.e. solid, liquid and gas)

The performance equations for constant density systems are identical for (A) P.F.R. and backmix reactor (B) P.F.R. and batch reactor (C) P.F.R, batch reactor and backmix reactor (D) Batch reactor and backmix reactor

Description : The performance equations for constant density systems are identical for (A) P.F.R. and backmix reactor (B) P.F.R. and batch reactor (C) P.F.R, batch reactor and backmix reactor (D) Batch reactor and backmix reactor

Last Answer : (B) P.F.R. and batch reactor

For an ideal plug flow reactor, the value of Peclet number is (A) 0 (B) 1 (C) 10 (D) ∞

Description : For an ideal plug flow reactor, the value of Peclet number is (A) 0 (B) 1 (C) 10 (D) ∞

Last Answer : (A) 0

For a packed bed reactor; the presence of a long tail in the residence time distribution curve is an indication of: (A) Ideal plug flow (B) Bypass (C) Dead zone (D) Channelling

Description : For a packed bed reactor; the presence of a long tail in the residence time distribution curve is an indication of: (A) Ideal plug flow (B) Bypass (C) Dead zone (D) Channelling

Last Answer : (C) Dead zone

Which of the following is the most suitable for isothermal operation? (A) Batch reactor (B) Back-mix reactor (C) Plug-flow reactor (D) Fixed bed reactor

Description : Which of the following is the most suitable for isothermal operation? (A) Batch reactor (B) Back-mix reactor (C) Plug-flow reactor (D) Fixed bed reactor

Last Answer : (B) Back-mix reactor

Pick out the wrong statement: (A) Chemical reactions with high activation energy are very temperature sensitive (B) A flat velocity profile exists in a plug flow reactor (C) The residence time for all the elements of fluid in case of a P.F.R. need not be same (D) Half life of a reaction increases with increased initial concentration for reaction orders more than one

Description : Pick out the wrong statement: (A) Chemical reactions with high activation energy are very temperature sensitive (B) A flat velocity profile exists in a plug flow reactor (C) The residence ... D) Half life of a reaction increases with increased initial concentration for reaction orders more than one

Last Answer : (C) The residence time for all the elements of fluid in case of a P.F.R. need not be same

With increase in the order of reaction (for all positive reaction orders), the ratio of the volume of mixed reactor to the volume of plug flow reactor (for identical feed composition, flow rate and conversion). (A) Increases (B) Decreases (C) Remain same (D) Increases linearly

Description : With increase in the order of reaction (for all positive reaction orders), the ratio of the volume of mixed reactor to the volume of plug flow reactor (for identical feed composition, flow rate and conversion). (A) Increases (B) Decreases (C) Remain same (D) Increases linearly

Last Answer : (A) Increases

For series reaction, the relative yield (A) Is always greater for plug-flow reactor than for the single CSTR of the same volume (B) Statement in (A) is wrong (C) Decreases with increasing conversion (D) Both (A) and (C) hold good

Description : For series reaction, the relative yield (A) Is always greater for plug-flow reactor than for the single CSTR of the same volume (B) Statement in (A) is wrong (C) Decreases with increasing conversion (D) Both (A) and (C) hold good

Last Answer : (D) Both (A) and (C) hold good

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

An endothermic second order reaction is carried out in an adiabatic plug flow reactor. The rate of heat generation is: (A) Maximum at the inlet of the reactor (B) Maximum at the exit of the reactor (C) Maximum at the centre of the reactor (D) Constant throughout the reactor

Description : An endothermic second order reaction is carried out in an adiabatic plug flow reactor. The rate of heat generation is: (A) Maximum at the inlet of the reactor (B) Maximum at the exit of the reactor (C) Maximum at the centre of the reactor (D) Constant throughout the reactor

Last Answer : (A) Maximum at the inlet of the reactor

Pick out the wrong statement. (A) The integral method of analysing kinetic data is used when the data is scattered (B) The differential method of analysing kinetic data requires more accurate or larger amounts of data (C) When the reaction rate is independent of temperature, the reaction is said to be of zero order (D) The ratio of volumes of plug flow reactor to that of mixed reactor is always less than one for identical feed composition, flow rate, conversion and for all positive reaction orders

Description : Pick out the wrong statement. (A) The integral method of analysing kinetic data is used when the data is scattered (B) The differential method of analysing kinetic data requires more accurate ... less than one for identical feed composition, flow rate, conversion and for all positive reaction orders

Last Answer : (C) When the reaction rate is independent of temperature, the reaction is said to be of zero order

The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit conversion is 20%, then the exit temperature (in k) is (Data: Heat of reaction at 298 K = - 50000 kJ/ kmole of A reacted Heat capacities CPA = CPB = 100kJ/kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Description : The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit ... /kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Last Answer : (C) 600

Kinetics of a catalytic reaction can be best studied on a/an __________ reactor. (A) Mixed (B) Integral (plug flow) (C) Differential (flow) (D) Either (A), (B) and (C)

Description : Kinetics of a catalytic reaction can be best studied on a/an __________ reactor. (A) Mixed (B) Integral (plug flow) (C) Differential (flow) (D) Either (A), (B) and (C)

Last Answer : (D) Either (A), (B) and (C)

The size of plug flow reactor (PFR) for all positive reaction orders and for any given duty, is __________ that of mixed reactor. (A) Greater than (B) Equal to (C) Smaller than (D) Unpredictable from the data

Description : The size of plug flow reactor (PFR) for all positive reaction orders and for any given duty, is __________ that of mixed reactor. (A) Greater than (B) Equal to (C) Smaller than (D) Unpredictable from the data

Last Answer : (C) Smaller than

Kinetics of a solid catalysed reaction can best be studied in a __________ reactor. (A) Batch (B) Plug-flow (C) Mixed (D) None of these

Description : Kinetics of a solid catalysed reaction can best be studied in a __________ reactor. (A) Batch (B) Plug-flow (C) Mixed (D) None of these

Last Answer : (C) Mixed

Which of the following is the optimum operating condition for an exothermic reversible reaction taking place in a plug-flow reactor? (A) Temperature should be high in the beginning and decreased towards the end of the reaction (B) Very low temperature should be used throughout the reaction (C) Very high temperature should be used throughout the reaction (D) None of these

Description : Which of the following is the optimum operating condition for an exothermic reversible reaction taking place in a plug-flow reactor? (A) Temperature should be high in the beginning and decreased towards ... reaction (C) Very high temperature should be used throughout the reaction (D) None of these

Last Answer : (A) Temperature should be high in the beginning and decreased towards the end of the reaction

For all positive reaction orders for a particular duty, (A) Mixed reactor is always larger than the plug-flow reactor (B) Ratio of the volume of the mixed reactor to that of the plug-flow reactor decreases with order (C) Reactor size is independent of the type of flow (D) Density variation during reaction affects design

Description : For all positive reaction orders for a particular duty, (A) Mixed reactor is always larger than the plug-flow reactor (B) Ratio of the volume of the mixed reactor to that of the plug-flow ... (C) Reactor size is independent of the type of flow (D) Density variation during reaction affects design

Last Answer : (A) Mixed reactor is always larger than the plug-flow reactor

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Description : Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Last Answer : (A) Axial flow mixers

Which of the following will give maximum gas conversion? (A) Fixed bed reactor (B) Fluidised bed reactor (C) Semi-fluidised bed reactor (D) Plug-flow catalytic reactor

Description : Which of the following will give maximum gas conversion? (A) Fixed bed reactor (B) Fluidised bed reactor (C) Semi-fluidised bed reactor (D) Plug-flow catalytic reactor

Last Answer : (C) Semi-fluidised bed reactor

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

N' plug flow reactors in series with a total volume 'V' gives the same conversion as a single plug flow reactor of volume 'V' for __________ order reactions. (A) First (B) Second (C) Third (D) Any

Description : N' plug flow reactors in series with a total volume 'V' gives the same conversion as a single plug flow reactor of volume 'V' for __________ order reactions. (A) First (B) Second (C) Third (D) Any

Last Answer : (D) Any

Recycling back of outlet stream to the reactor from an ideal CSTR carrying out a first order liquid phase reaction will result in __________ in conversion. (A) Decrease (B) Increase (C) No change (D) Either (A) or (B), depends on the type of reaction

Description : Recycling back of outlet stream to the reactor from an ideal CSTR carrying out a first order liquid phase reaction will result in __________ in conversion. (A) Decrease (B) Increase (C) No change (D) Either (A) or (B), depends on the type of reaction

Last Answer : (C) No change

The Stoke's stream function applies to the (A) Irrotational flow only (B) Ideal/non i viscous fluids only (C) Cases of axial symmetry (D) None of these

Description : The Stoke's stream function applies to the (A) Irrotational flow only (B) Ideal/non i viscous fluids only (C) Cases of axial symmetry (D) None of these

Last Answer : (C) Cases of axial symmetry

An isothermal irreversible reaction is being carried out in an ideal tubular flow reactor. The conversion in this case will __________ with decrease in space time. (A) Increase (B) Increase exponentially (C) Decrease (D) Remain unchanged

Description : An isothermal irreversible reaction is being carried out in an ideal tubular flow reactor. The conversion in this case will __________ with decrease in space time. (A) Increase (B) Increase exponentially (C) Decrease (D) Remain unchanged

Last Answer : (C) Decrease

Pick out the wrong statement. (A) 'Hold back' is defined as the fraction of material that stays longer than the mean residence time (B) Study of non-ideal flow reactor is done experimentally by stimulus￾response technique (C) For studying a chemical reaction, it is desirable to monitor the reactants during initial stages and the products during the final stages of reaction (D) A batch reactor cannot be used to study the kinetics of catalytic reaction

Description : Pick out the wrong statement. (A) 'Hold back' is defined as the fraction of material that stays longer than the mean residence time (B) Study of non-ideal flow reactor is done experimentally ... final stages of reaction (D) A batch reactor cannot be used to study the kinetics of catalytic reaction

Last Answer : (D) A batch reactor cannot be used to study the kinetics of catalytic reaction

The power number for a stirred tank becomes constant at high Reynolds number. In this limit, the variation of power input with impeller rotational speed (N) is proportional to (A) N° (B) N 1 (C) N 2 (D) N 3

Description : The power number for a stirred tank becomes constant at high Reynolds number. In this limit, the variation of power input with impeller rotational speed (N) is proportional to (A) N° (B) N 1 (C) N 2 (D) N 3

Last Answer : (C) N

At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 /μ: Reynold's number N is the impeller rotational speed, and D is the impeller diameter. (A) Po ∝ Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5

An isothermal aqueous phase reversible reaction, P ⇌ R, is to be carried out in a mixed flow reactor. The reaction rate in k.mole/m3 .h is given by, r = 0.5CP - 0.125CR. A stream containing only P enters the reactor. The residence time required (in hours) for 40% conversion of P is (A) 0.80 (B) 1.33 (C) 1.60 (D) 2.67

Description : An isothermal aqueous phase reversible reaction, P ⇌ R, is to be carried out in a mixed flow reactor. The reaction rate in k.mole/m3 .h is given by, r = 0.5CP - 0.125CR. A stream containing only P enters the reactor. The ... (in hours) for 40% conversion of P is (A) 0.80 (B) 1.33 (C) 1.60 (D) 2.67

Last Answer : (C) 1.60

Baffles in mixing tanks are provided to (A) Reduce swirling and vortex formation (B) Increase the structural strength of the tank (C) Aid in rotational flow (D) None of these

Description : Baffles in mixing tanks are provided to (A) Reduce swirling and vortex formation (B) Increase the structural strength of the tank (C) Aid in rotational flow (D) None of these

Last Answer : (A) Reduce swirling and vortex formation

Exothermic reactions are best carried out in (A) A CSTR (B) CSTR in series (C) A plug flow reactor followed by CSTR (D) CSTR followed by a plug flow reactor

Description : Exothermic reactions are best carried out in (A) A CSTR (B) CSTR in series (C) A plug flow reactor followed by CSTR (D) CSTR followed by a plug flow reactor

Last Answer : (D) CSTR followed by a plug flow reactor