List the applications of RC oscillator and crystal oscillator.

List the applications of RC oscillator and crystal oscillator.
by

1 Answer

Answer :

Applications of RC oscillator : 

1) In AF signal generators 2) In radio transmitter & Receivers 3) Sine wave generator. 


Applications of Crystal oscillator :

1) Electronic navigation systems 2) Frequency Synthesizers 3) Timing circuits (Clock) with high stability. 4) RADAR systems. 

by

Related questions

Compare between RC phase shift oscillator and crystal oscillator.

Description : Compare between RC phase shift oscillator and crystal oscillator.

Last Answer : RC phase shift oscillator Crystal oscillator This oscillator is used for low frequency range. Quartz crystal is mainly used in radio-frequency (RF) oscillators Used resistor and capacitor ... RC network is used as feedback network. Crystal is connected in feedback.

crystal oscillator and its applications.

Description : crystal oscillator and its applications.

Last Answer : Need: Any circuit that generates an alternating voltage is called an oscillator. To generate ac Voltage, it takes energy from the dc source. 1. In some applications voltages of low frequency are required where ... generate clock in digital systems.  It is used as sweep circuits in TV and CRO.

Differentiate between positive and negative feedback on the basis of . (i) overall phase shift (ii) voltage gain (iii) stability (iv) applications

Description : Differentiate between positive and negative feedback on the basis of . (i) overall phase shift (ii) voltage gain (iii) stability (iv) applications 

Last Answer : Compare positive feedback and negative feedback on the basis of: (i) Gain (ii) Bandwidth (iii) Phase shift (iv) Stability

Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Description : Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Last Answer : Frequency of oscillation is given by,

Compare RC and LC oscillator.

Description : Compare RC and LC oscillator.

Last Answer :  RC and LC oscillator

Draw and explain RC phase shift Oscillator.

Description : Draw and explain RC phase shift Oscillator.

Last Answer : Circuit diagram of RC phase shift oscillator: WORKING: * Circuit consists of a single stage amplifier in common emitter configuration & RC phase shifting network. * R1, R2, RE provides biasing & CE ... . * The phase shift around the loop is 3600 only at one precise frequency.  

Refer to the deviation of the operating frequency of a crystal oscillator from its nominal value due to temperature variations. A. Drift B. Flash over C. Frequency deviation D. Deviation ratio

Description : Refer to the deviation of the operating frequency of a crystal oscillator from its nominal value due to temperature variations. A. Drift B. Flash over C. Frequency deviation D. Deviation ratio

Last Answer : A. Drift

What is Miller crystal oscillator? Explain its operation.

Description : What is Miller crystal oscillator? Explain its operation.

Last Answer : It is nothing but a Hartley oscillator its feedback Network is replaced by a crystal. Crystal normally generate higher frequency reactance due to the miller capacitance are in effect between the transistor terminal.

Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Description : Six (6) MHz crystal oscillator has a stability of 1 part in 106. The largest frequency error expected of this crystals A) 0.06 Hz B) 0.6 Hz C) 6 Hz D) 60 Hz.

Last Answer : C) 6 Hz

An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Description : An oscillator that uses crystal control should be A) Frequency stable B) useful only at low frequencies C) AVFO D) none of the above.

Last Answer : A) Frequency stable

State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Description : State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Last Answer : Basic Principle: The main principle of a piezoelectric crystal is that a mechanical force, when applied on the crystal, it vibrates and produces electric charges on the crystal surface. When ac voltage is applied across crystal, it vibrates at the frequency of the applied voltage. (OR)

Draw the circuit diagram of crystal oscillator and explain its working.

Description : Draw the circuit diagram of crystal oscillator and explain its working.

Last Answer : To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good.  The resonant frequency is given as  Fo = 1/( 2 π √LC ) 

In a radio transmitter, the frequency of the crystal oscillator will be stable for a long time if the quality factor

Description : In a radio transmitter, the frequency of the crystal oscillator will be stable for a long time if the quality factor of the crystal resonator is  (a) > 100 (b) > 500 (c) > 1000 (d) > 20000

Last Answer : In a radio transmitter, the frequency of the crystal oscillator will be stable for a long time if the quality factor of the crystal resonator is  > 1000

The crystal oscillator frequency is very stable due to

Last Answer : The crystal oscillator frequency is very stable due to High Q of the crystal.

The main advantage of crystal oscillator is that its output is:

Last Answer : The main advantage of crystal oscillator is that its output is: A Constant frequency range

List configurations of BJT.

Description : List configurations of BJT. 

Last Answer : Configurations of BJT : 1) Common Base (CB) configuration 2) Common Emitter (CE) configuration 3) Common Collector (CC) configuration

Define rectifier and list its types.

Description : Define rectifier and list its types. 

Last Answer : Definition: A rectifier is a circuit that converts AC input voltage into DC output voltage.  Types : 1) Half wave rectifier  2) Center tap full wave rectifier. 3) Bridge Rectifier 

Which of the following is a negative-resistance microwave device for oscillator applications?

Description :  Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

Last Answer :  Which of the following is a negative-resistance microwave device for oscillator applications? A) IMPATT Diode B) Gunn Diode C) Snap diode D) Schottky Diode 

applications of RC coupled amplifier

Description :  applications of RC coupled amplifier

Last Answer : Applications of RC coupled amplifier: (i) Widely used as Voltage amplifiers. (ii) They are used in Public Address System. (iii) In Tape recorders. (iv) In stereo amplifiers (v) In T.V. V.C.R. and C.D. Players.

Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail.

Description : Draw output characteristics of common emitter [CE] configuration and explain active, saturation and cut-off regions in detail. 

Last Answer : Characteristics of common emitter [CE] configuration Explanation :  (1) Active Region: In this region collector junction is reverse biased and emitter junction is forward biased. It is ... the transistor collector current is approximately given by VCC / RC and independent of base current. 

Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT configuration having current gain less than one. (iv) BJT configuration suitable for impedance matching. (v) BIT configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.

Description : Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT ... configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.  

Last Answer : (i) BJT configuration having the least current gain : Common Base Configuration  (ii) KIT configuration called as voltage follower: Common Collector Configuration  (iii) BJT ... Emitter Configuration  (vi) BJT configuration having the least output impedance: Common Collector Configuration

Describe the working principle of photodiode with proper diagram.

Description : Describe the working principle of photodiode with proper diagram.

Last Answer : Diagram of photo diode : Working principle of photo diode :  When photons of energy greater than 1.1 eV hit the diode, electron-hole pairs are created. The intensity of photon ... , the holes move toward the anode and the electrons move toward the cathode, thereby producing photocurrent. 

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform.

Description : Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform. 

Last Answer : Circuit diagram of bridge rectifier with π filter : Input and output waveform:

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

Describe transistor as a switch with neat sketch.

Description : Describe transistor as a switch with neat sketch.

Last Answer : In Bipolar Transistor as a Switch the biasing of the transistor, either NPN or PNP is arranged to operate the transistor at both sides of the I-V characteristics curves. The areas ... possible and maximum current flowing through the transistor. Therefore the transistor is switched Fully-ON .

Draw block diagram of IC 723. Write the functions of IC 723.

Description : Draw block diagram of IC 723. Write the functions of IC 723.

Last Answer : Functions of IC 723 : 1. Series, shunt, switching and floating regulators 2. Basic Low-voltage Regulator (Vo = 2 to 37 volts) 3. Low Voltage High Current Regulator.  ... off is obtained by connecting a small capacitor of 100 pF between frequency compensation and inverting input terminals. 

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

Draw the symbol, logic expression and truth table of NOR gate.

Description : Draw the symbol, logic expression and truth table of NOR gate.

Last Answer : symbol, logic expression and truth table of NOR gate

Define the term line regulation.

Description : Define the term line regulation. 

Last Answer : Line regulation is the ability of a power supply to maintain a constant output voltage irrespective of any changes in input voltage. 

Suggest the suitable diode type for rectifier circuit.

Description : Suggest the suitable diode type for rectifier circuit. 

Last Answer : Any general purpose diodes 1N4001 to 1N4007 series  Or Silicon diode & Germanium diode 

Draw the symbol of LED & photodiode.

Description : Draw the symbol of LED & photodiode. 

Last Answer : Symbol of LED & photodiode

What does the liquid crystal display require for computer applications?

Description : What does the liquid crystal display require for computer applications?

Last Answer : An external light source, called a backlight.

List two types of oscillator, which generates frequency in RF range.

Description : List two types of oscillator, which generates frequency in RF range.

Last Answer : Types of Oscillators generating frequencies in RF range: i) Hartley Oscillator ii) Colpitt’s Oscillator iii) Clapp Oscillator

Opera RC does not list unite in panel?

Description : Opera RC does not list unite in panel?

Last Answer : If you have the same computer I have, use eRecovery to switch your computer settings back to the original settings from the day it was bought. I know it isn't the best of ideas, but it ... you don't have eRecovery, you might have a different type of recovery program/option in your computer?)

List the advantages of RC coupled amplifier.

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

List out the types of crystal structure.

Description : List out the types of crystal structure.  

Last Answer : Types of crystal structures. (i) Atomic atructure (ii) Nano sturucture (iii) Microsturcture (iv) Macrostructure

Is this oscillator adjustable with a screwdriver, and where is the link to prchase it?

Description : Is this oscillator adjustable with a screwdriver, and where is the link to prchase it?

Last Answer : answer:@XOIIO Probably a question you should direct to the company. The link below should help. http://www.vectron.com/contact/index.htm

WHAT ARE THE EFFECT OF PUTTING APALNT ON AN OSCILLATOR, WOULD IT DIE ?

Description : WHAT ARE THE EFFECT OF PUTTING APALNT ON AN OSCILLATOR, WOULD IT DIE ?

Last Answer : Need Answer

What is an oscillator ? What is an oscillator ?

Description : What is an oscillator ? What is an oscillator ?

Last Answer : Devices that can convert DC power to AC power at a certain frequency are called oscillators.

What is role of LC circuit in the hartley oscillator?

Description : What is role of LC circuit in the hartley oscillator?

Last Answer : Self-tuning feedback

When two semiconductors of p-and ntype are brought in contact, they form p-n junction which acts like a/an – (1) Conductor (2) Oscillator (3) Rectifier (4) Amplifier

Description : When two semiconductors of p-and ntype are brought in contact, they form p-n junction which acts like a/an – (1) Conductor (2) Oscillator (3) Rectifier (4) Amplifier

Last Answer : (3) Rectifier Explanation: P-n junction is a device which flows current in one direction when it is forward biased and when it is reverse biased it doesn't flow any current through it. So it ... (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction.

The device which converts AC to DC is (1) Oscillator (2) Amplifier (3) Rectifier (4) None of these

Description : The device which converts AC to DC is (1) Oscillator (2) Amplifier (3) Rectifier (4) None of these

Last Answer : (3) Rectifier Explanation: A rectifier is an electrical device that converts alternating current (AC). which periodically reverses direction, to direct current (DC), which flows in only one ... serving as components of DC power supplies and high-voltage direct current power transmission systems.

Alternating current is converted into direct current by a – (1) Transformer (2) Dynamo (3) Oscillator (4) Rectifier

Description : Alternating current is converted into direct current by a – (1) Transformer (2) Dynamo (3) Oscillator (4) Rectifier

Last Answer : (4) Rectifier Explanation: A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. The process is known as rectification.

Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Description : Not a reason for the use of an antenna coupler. A. To make the antenna look resistive B. To provide the output amplifier with the correct load impedance C. To discriminate against harmonics D. To prevent re-radiation of the local oscillator

Last Answer : D. To prevent re-radiation of the local oscillator

What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz

Description : What is the local oscillator (mixer) frequency of the satellite with an uplink frequency in GHz band? A. 3500 MHz B. 4500 MHz C. 2225 MHz D. 2555 MHz

Last Answer : C. 2225 MHz

Which of the following best describes a dip-meter? A. An SWR meter B. A counter C. A variable LC oscillator with metered feedback current D. A field strength meter

Description : Which of the following best describes a dip-meter? A. An SWR meter B. A counter C. A variable LC oscillator with metered feedback current D. A field strength meter

Last Answer : C. A variable LC oscillator with metered feedback current

When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Description : When measuring a transmitter’s frequency against a suitable standard, the frequency to be measured is taken from the A. oscillator stage B. intermediate amplifier C. buffer stage D. final RF stage

Last Answer : D. final RF stage

What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Description : What establishes the receiver bandwidth? A. RF amplifier B. Mixer C. Local oscillator D. IF amplifier

Last Answer : D. IF amplifier

An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Description : An FM receiver whose intermediate frequency is 10.7 MHz, is experiencing image channel interference from a station transmitting on 121.1 MHz. If the local oscillator is tracking above, the receiver is tuned to A. 131.8 MHz B. 110.4 MHz C. 142.5 MHz D. 99.7 MHz

Last Answer : D. 99.7 MHz

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator