Description : __________ pumps are axial flow pumps. (A) Turbine (B) Propeller (C) Diffuser (D) None of these
Last Answer : (B) Propeller
Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these
Last Answer : (A) Is suitable for mixing low viscosity liquids
Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)
Last Answer : (A) Produces mainly axial flow
Description : Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above
Last Answer : a.100-120 rpm
Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions
Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow
Description : Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers
Last Answer : (A) Axial flow mixers
Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow ... centrifugal pump, is always higher than that of volute type (D) All the above
Last Answer : (D) All the above
Description : The propeller shaft speed in a turbo-electric, synchronous, propulsion drive motor is changed by varying the __________. A. turbine speed B. number of motor poles C. field strength of the generator D. field strength of the motor
Last Answer : Answer: A
Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)
Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow
Description : Which of the following is the most suitable for handling fibrous and dense slurries? (A) Propeller agitator (B) Cone type agitator (C) Turbine agitator
Last Answer : (B) Cone type agitator
Description : Which of the following agitators having a large blade area, rotating at slow speed is used for mixing high viscosity liquids (> 50000 centipoise)? (A) Propeller (B) Helical screw (C) Flat blade turbine (D) Curved blade turbine
Last Answer : (B) Helical screw
Description : For a turbine agitated and baffled tank, operating at low Reynold's number (based on impeller diameter), the power number (Np ) varies with NRe as (A) Np ∝ NRe (B) Np ∝ √NRe (C) Np → constan (D) Np ∝ 1/NRe
Last Answer : (D) Np ∝ 1/NRe
Description : Turbine impeller (A) Produces only radial current (B) Produces only tangential current (C) Is effective over wide range of viscosities (D) Does not produce tangential current
Last Answer : (C) Is effective over wide range of viscosities
Description : The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these
Last Answer : (B) Have different diameters
Description : A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these
Last Answer : (B) Vaned diffusion casing
Description : A turbine is said to have an axial discharge when the steam leaves the blade tip at _________ to the direction of the blade motion. (A) 60° (B) 90° (C) 180° (D) 270°
Last Answer : (B) 90°
Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed
Last Answer : (A) Density of the liquid
Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these
Last Answer : (C) Avoid chances of separation inside the impeller
Description : Design of the casing of centrifugal pump should be such as to minimise the (A) Back flow through impeller (B) Loss of kinetic head (C) Loss of static head (D) None of these
Last Answer : (B) Loss of kinetic head
Description : High specific speed of a pump implies that, it is a/an __________ pump. (A) Centrifugal (B) Mixed flow (C) Axial flow (D) None of these
Last Answer : (C) Axial flow
Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these
Last Answer : (A) Axial
Description : Low specific speed of a pump implies that, it is a/an __________ pump. (A) Axial flow (B) Centrifugal (C) Mixed flow (D) None of these
Last Answer : (B) Centrifugal
Description : Working of a __________ pump characterises mixed flow. (A) Turbine (B) Piston (C) Diaphragm (D) None of these
Last Answer : (A) Turbine
Description : In case of a __________ the energy of flow is considerably decreased downstream of the machine. (A) Blower (B) Turbine (C) Centrifugal pump (D) Centrifugal fan
Last Answer : (B) Turbine
Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : The maximum head that can be developed by a single impeller is __________ ft. (A) 25 (B) 100 (C) 250-300 (D) 1000
Last Answer : (C) 250-300
Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these
Last Answer : (D) None of these
Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall
Last Answer : (A) Manometric
Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)
Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)
Description : The blades of a centrifugal impeller are said to be curved forward, if the __________ of the motion of impeller blades. (A) Inlet tip of a blade curves in a direction opposite to that (B) Outlet tip ... Inlet tip of a blade is towards the direction (D) Outlet tip of a blade is towards the direction
Last Answer : (D) Outlet tip of a blade is towards the direction
Description : In case of a, centrifugal pump, the ratio h1/h2is termed as the __________ efficiency (where, h1 = actual measured head & h2 = head imparted to the fluid by impeller). (A) Mechanical (B) Overall (C) Volumetric (D) Impeller
Last Answer : A) Mechanical
Description : The Stoke's stream function applies to the (A) Irrotational flow only (B) Ideal/non i viscous fluids only (C) Cases of axial symmetry (D) None of these
Last Answer : (C) Cases of axial symmetry
Description : While starting an axial flow pump, its delivery valve should be kept (A) Open (B) Closed (C) Either open or closed (D) None of these
Last Answer : (A) Open
Description : Which of the following is most prone to pulsating discharge flow? (A) Centrifugal pump (B) Reciprocating pump (C) Gear pump (D) Axial flow pump
Last Answer : (C) Gear pump
Description : Which of the following can be used to create a flow of gas, where no significant compression is required? (A) Reciprocating compressor (B) Blower (C) Axial flow compressor (D) Centrifugal compressor
Last Answer : (B) Blower
Description : A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction
Last Answer : (B) Is same as ideal stirred tank reactor
Description : In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant
Last Answer : (B) Velocity of reaction can be controlled
Description : A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture
Last Answer : (C) Presence of lateral mixing
Description : The most suitable equipment used to devulcanise rubber scrap and to make water dispersion & rubber solution is a (A) Boundary mixer (B) Propeller agitator (C) Sharpies centrifuge
Last Answer : (A) Boundary mixer
Description : Propeller type centrifugal pumps are most suitable for (A) High capacity at high heads (B) High capacity at low heads (C) Low capacity at high heads (D) Low capacity at low heads
Last Answer : (B) High capacity at low heads
Description : What kind of bird can land in a tree like a black bird, but then jump out of the tree into the water and paddle around like a duck?
Last Answer : answer:Four ducks that nest in trees. http://www.ehow.com/info_8309866_do-ducks-nest-tall-trees.html
Description : Any tips for SUP (Stand up paddle boarding) techniques, do's and dont's and purchase?
Last Answer : Rent first, wider and longer are better. Start out paddling on protected cove or bay, less wave action. Enjoy yourself.
Description : Do I really need a "paddle attachment"?
Last Answer : It's just that the batter gets really hard to mix with a mixer at a certain point. The paddle makes it easier or you can just change over to a wooden spoon when it gets too stiff. I just ... paper I think the easy release foil is just a sponsor endorsement. You can see a picture on my cooking blog
Description : what- Dexter designs a paddle fan.Which angle appears to be the angle of rotation in his design?
Last Answer : 60 degrees
Description : I fooled around with the boys and we broke the paddle to the boat. Is there a way to fix it? How to fix that rod when it's broken?
Last Answer : What is the rod made of ??? Dural, laminate, kevlar, wood ... And also write the type of paddle - for some, changing the pole is not worth it ...
Description : A light paddle wheel placed in the path of________will rotate.
Last Answer : A light paddle wheel placed in the path of________will rotate. A. cathode rays B. `alpha`-rays C. `beta`-rays D. All the above
Description : What are the little bumps on the face of a ping pong paddle called?
Last Answer : Need answer
Description : Why low head dams dangerous to small boats and paddle craft?
Last Answer : Backwash can pin you and the boat indefinitely.
Description : Where to get paddle boats from?
Last Answer : Wayfair.com has a great selection on paddleboats. They even ship so you can bet you'll have yours within a time limit depending on your budget. Walmart.com has them too.